Source range and intermediate range nuclear instruments Flashcards

1
Q

A loss of control power to SR or IR instruments below P6(P10) or above P6(P10) when not blocked will result in ______.

A

Reactor trip

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

A loss of instrument power to SR or IR instruments below P6(P10) or above P6(P10) when not blocked will result in ______ unless the _____switch is in ______.

A

Reactor trip
Level trip switch
Bypass

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Above P6/P10 when SR IR trips blocked, reactor trip ______occur on loss of ______.

A

will not
Instrument or control power

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

The _____ switch will block both the ______ trip and _______ rod stop.

A

level trip bypass

IR flux high trip

IR flux high rod stop

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

When instrument power is lost, ______ on the instrument drawer go out. _____goes out when ____ is lost.

A

All lights
Control power on
Control power

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

If one IR channel inoperable _____ or ______.

A

Reduce power to

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

If both IR channels inoperable ______ and _______.

A

Suspend positive reactivity additions immediately
-and-
Reduce power to

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

The following 4 circuits are energized to actuate:

A
  1. RWST L0-2 level 46.7% 2/4
  2. Containment pressure hi-3 pressure 20 psig 2/4
  3. P-6 SR block permissive 1.0E-5% RTP IR, energize at power
  4. P-11 PZR pressure low permissive 1930 psig 2/3
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

N31/N35 and N32/N36 SR/IR detectors are ________ that operate in the ______ region.

A

Fission chamber detectors that operate in the ionization region.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Function of wide range amplifier:

A

Device provides the power supply for the detectors, receives the output of the detector, and does the pulse shaping and discriminating necessary for the Source range. Also performs initial signal processing for the IR Channels

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

The optical isolator has a power supply switch on the front that selects _____ or ______.

A

Instrument bus 111/112 or ESF MCC bus 131X2/132X2

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Inside the Optical Isolator cabinet is a switch:

A

App R or test position. Normally in test but can be switched for control room inaccessibility.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What is the advantage of using a fission chamber verses the BF3 detectors?

A

-High reliability in a harsh environment
-Can operate in a gamma flux in excess of 10E4 R/hr w/o damage or loss of sensitivity

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

SR uses output from ____ chamber(s) (risen sensitivity) while IR uses output of _____ chamber(s).

A

Both fission chambers

Single fission chamber

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Due to “coincidence”, the effect of having one fission chamber (is/is not) noticeable at _____ count rates

A

is not; higher count rates

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Audio count rate channel drawer is powered from _____ and loss of power _______.

A

AC bus 114

Disables all functions

17
Q

Control power and instrument power is supplied from _____ and ______ for N31/32 35/36.

A

Instrument bus 111 and 112

18
Q

In the ESF power supply position, power is supplied to give post accident monitoring indication at ____ and the ____.

A

0PM02J and the fire hazards panel

19
Q

Power supply swap, what two locations and any additional details?

A

Located on the outside of the Optical Isolator.
Switch on the back of the PM05J in the Control Room is selectable to INST only
ESF will deenergize the circuit

20
Q

The purpose of the SR high flux trip is ______.

A

Protection for uncontrolled RCCA bank rod withdrawal accident from a subcritical condition during startup.

21
Q

SR high flux trip
____ be bypassed
_____ be blocked with ________
_____blocked above ______

A

Can be Bypassed

Can be blocked with P-6 (1 of 2 IR > 10-5% power)

Is blocked above P-10 (2 of 4 PR > 10% Power)

22
Q

LCO 3.3.4 Remote shutdown panel, which instrumentation are required? Time to restore?

A
  1. Intermediate Range Neutron Flux
  2. Source Range Neutron Flux
  3. Reactor Coolant Temperature - Wide Range
    a. Hot Leg (per loop)
    b. Cold Leg (per loop)
  4. Pressurizer Pressure
  5. Pressurizer Level
  6. Steam Generator Pressure (per SG)
  7. Steam Generator Level (per SG)
  8. Residual Heat Removal Temperature
  9. Auxiliary Feedwater Flow Rate (per SG)

30 days to restore