Bx Test 12

Question 1

Setting up the tower ladder apparatus is key to safe operation. Which choice is CORRECT about setting up the tower ladder?
A: While not preferred, tower ladders are designed to operate with outriggers and jacks down on one side while on level ground.

B: Jacks and outriggers are controlled by individual levers or an all jacks lever. The All Jacks lever is the preferred method for lowering on other than level ground.

C: If the apparatus is not level, lower the jacks/tormentors on the high side followed by the jacks/tormentors on the low side until the green lights indicate proper deployment.

D: Raising the high side fully before raising the low side can be a safety hazard and may cause damage to the suspension system.

Answer 1

D
Explanation:
TOWER LADDERS - CHAPTER 1
A – Incorrect – They are not designed to operate with outriggers and jacks down on one side only. 1.1
B – Incorrect – The All Jacks is the preferred method for lowering ON LEVEL GROUND. 1.1
C – Incorrect – Low side first 1.1
D – Correct 1.1

Question 2

The members of Tower Ladder 99 are finishing up roll call and begin their inspection of the rig. Which of the following inspections is conducted each tour?
A: The level of the platform of the bucket.

B: Condition of the safety belts installed in the bucket.

C: Verify the platform control switch on the pedestal is not engaged.

D: Evidence of hydraulic leaks at all connections.

Answer 2

C
Explanation:
TOWER LADDERS CHAPTER 7
C is Correct – At the start of each tour, verify the platform switch on the pedestal is not engaged as this will deactivate the bucket controls. Pg 1
A, B, D are all daily inspections.

Question 3

Positioning on narrow streets always presents the possibility of encountering a parked car during set up. Which choice below is CORRECT regarding positioning under these circumstances?
A: A guide firefighter, typically the roof firefighter, should assist the chauffeur in positioning the apparatus.

B: When positioning a 95’ tower ladder, a six-foot hook can be used as a guide to determine if the outriggers will clear all obstructions.

C: Presetting apparatus spotlights may provide an estimate of the final outrigger location at night.

D: Using the knuckle at the bottom of the outrigger may help the chauffeur assess the clearance between the apparatus and parked cars.

Answer 3

C
Explanation:
TOWER LADDERS – CHAPTER 1
A – Incorrect – typically the OVM firefighter. 1.1 PG 3
B – Incorrect – When positioning a 75’ TL the 6’ hook is sufficient. The Clearance for a 95’ tower ladder is 6’8” 1.1 PG 4
C – Correct – 1.1 PG 3
D – Incorrect – Clearance between parked cars (not the apparatus and parked cars). 1.1 pg 3

Question 4

The placement of the pins once the jacks and outriggers are extended are critical to the stability of the apparatus. Which choice is CORRECT regarding the preferred pin placement?
A: The preferred placement of manual pins for outriggers shall be at the lowest hole available.

B: The preferred placement of manual pins for jacks shall be at the lowest hole available.

C: The preferred placement of manual pins for outriggers and jacks shall be at the highest slot available once extended.

D: The preferred placement of manual pins for outriggers and jacks shall be at the lowest slot available once extended.

Answer 4

A
Explanation:
TOWER LADDERS – CHAPTER 1
A – Correct – 1.1 PG4
B – Incorrect – Highest hole available – 1.1 PG 4
C – Incorrect – Outriggers (lowest), Jacks (Highest) 1.1 PG 4
D – Incorrect – Outriggers (lowest), Jacks (Highest) 1.1 PG 4

Question 5

Tower Ladder placement will depend upon conditions encountered on arrival. Which of the following choices is not listed as a factor in tower ladder placement?
A: Fire Conditions – location and extent of fire.

B: Type of Structure – Height and Area.

C: Time of Day.

D: Smoke Conditions – light, medium, heavy.

Answer 5

D
Explanation:
TOWER LADDERS – CHAPTER 2
A, B, C Correct -2 PG 1
D – Not listed – Smoke Conditions are not listed as factors influencing TL positioning.

Question 6

The Tower Ladder bucket has a limited amount of space for firefighters. Which choice is the CORRECT maximum number of firefighters that should operate in the bucket?
A: 1

B: 2

C: 3

D: 4

Answer 6

B
Explanation:
TOWER LADDERS CHAPTER 1
B is Correct sec 1.3 PG 8 top

Question 7

Tower Ladder 1 is responding first due to a reported fire in a row of occupied Brownstone type Row Frame buildings. The Officer and members have a number of position related considerations to make. Which point below is INCORRECT?
A: The recommended apparatus positioning upon arrival should be for top floor VEIS.

B: A properly positioned Tower Ladder could potentially cover six row frame buildings.

C: Particular attention should be given to the larger room that shares two windows.

D: The LSR & Saw shall be taken to the roof when the bucket is used for roof access.

Answer 7

C
Explanation:
TOWER LADDERS CHAPTER 2
A – Correct – 2.1.1
B – Correct – 2.1.2 & Photo
C – Incorrect – Particular attention should be given to the small bedrooms having their only entrance from the hall. 2.12.1 pg 5.
D – Correct – 2.1.1 & 2.1.2

Question 8

When positioning the bucket for Rescue and Removal of people from windows, it is important to properly position the bucket for operation. Which choice below is CORRECT about bucket and apparatus positioning?
A: To expedite placing the bucket to a window, position the apparatus with the cab angled away from the objective lining up the bucket with the window.

B: To expedite placing the bucket to a window, position the apparatus parallel to the objective, lining up the bucket with the window.

C: To expedite placing the bucket to a window, position the apparatus parallel to the objective, lining up the turntable with the window.

D: To expedite placing the bucket to a window, position the apparatus with the cab angled away from the objective, lining up the turntable with the window.

Answer 8

B
Explanation:
TOWER LADDERS – CHAPTER 3
B is Correct – Chapter 3 3.3 pg 3

Question 9

Ladder 99 is responding to an advanced fire on the 1st & 2nd floors of a 2 ½ story peaked roof private dwelling. Which of the following is INCORRECT about their positioning upon arrival?
A: At an advanced fire, the main objective is to position a tower ladder in front of the fire building.

B: When possible, the preferred position is with the apparatus cab angled away from the building so the bucket can be placed over the corner of the building near the peak of the roof.

C: The turntable should be positioned to enable the bucket to cover two sides of the private dwelling

D: If the apparatus cannot be placed in the preferred position, place the bucket to the valley area where a hook ladder can be used to reach the peak.

Answer 9

B
Explanation:
TOWER LADDERS – CHAPTER 2
A – Correct 2.1.6 PG11
B – Incorrect – Parallel to the front of the building. PG11
C – Correct 2.1.6 PG 11
D – Correct 2.1.6 PG 12

Question 10

When positioning the tower ladder at a fire in a place of worship with access from all sides, which choice below most reflects the CORRECT sides(s) the apparatus should cover?
A: Exposure 1 or 3 side

B: Exposures 2 or 4 side

C: Exposures 2 & 3 sides

D: Exposures 1 & 4 sides

Answer 10

D
Explanation:
TOWER LADDERS – CHAPTER 2
2.1.8 States – At fires in places of Worship, the Tower Ladder should be positioned to cover two sides of the building and provide ventilation of the roof and rose window. The Rose window is exposure 1.
Choice D is Correct

Question 11

Which of the following is CORRECT regarding apparatus positioning and the scrub area of the tower ladder?
A: Generally, the boom has enough clearance to reach most 2nd floor windows and above when operating over the crew cab.

B: The ideal horizontal distance from the center line of the turntable to an objective is 32 feet.

C: When the center line of the turntable is 20 feet from a building, there is sufficient room for the bucket to be dropped below the horizontal with the boom perpendicular to the side of the apparatus.

D: Observing the relationship of the objective to the building line may assist chauffeurs with initial positioning.

Answer 11

B
Explanation:
TOWER LADDERS – CHAPTER 2
A – Incorrect – clearance to reach most 3rd floor windows. 2 PG 3 top
B – Correct – CH 2 pg 2 bottom
C – Incorrect – 25 feet from the building line CH 2 pg 2 bottom
D – Incorrect – relationship of the objective to the lines in the sidewalk. PG 2 bottom

Question 12

Which truck company member is responsible for personally verifying that all outriggers, jacks, and pins are properly placed prior to raising the boom?
A: Officer

B: Chauffeur

C: OVM Firefighter

D: Roof Firefighter

Answer 12

B
Explanation:
TOWER LADDERS CHAPTER 1
B is Correct – LCC 1.2 PG 6 top

Question 13

Tower Ladders have their own communications system installed. Which choice below is CORRECT regarding communicating during tower ladder operations?
A: A test of the intercom shall be made each tour, and at the initial stages of placing the Tower Ladder into operation.

B: When transmitting orders between the bucket and pedestal, the reference point is always the bucket position.

C: The HT tactical channel is the preferred means of communicating between the pedestal and bucket.

D: Boom Right is terminology that refers to rotating the boom to the bucket firefighter’s right.

Answer 13

A
Explanation:
TOWER LADDERS – CHAPTER 1
A – Correct - 1.5
B – Incorrect – Pedestal position
C – Incorrect – Intercom system
D – Incorrect – pedestal FF’s Right

Question 14

When it comes to deployment of the tower ladder stream, there are several precautions the members in the bucket must take. Which of the following choices below is CORRECT?
A: Prior to water delivery, set and lock the monitor in the direction of the start point of water delivery.

B: Unlike the Engine Company Multiversal, the stream shaper is not required to ensure a good quality stream and maximum reach.

C: Members must verify use of the installed safety belt, life belt, or personal harness secured to a substantial part of the bucket prior to calling for water.

D: If water will be applied to the horizontal or below, pull the safety pin on the waterway prior to calling for water.

Answer 14

C
Explanation:
TOWER LADDERS CHAPTER 4
A – Incorrect – Set and lock the monitor high in the air. 4.2
B – Incorrect – The stream shaper should normally be left in place 4.2
C – Correct 4.2
D – Incorrect – Below the horizontal, pull the pin on the waterway. 4.2

Question 15

You are the officer working in Tower Ladder 99 and you are charged with having the bucket supplied with water for TL operations.Which choice below is CORRECT regarding supply operations?
A: Water flow to the tower ladder should be controlled at the supply source (Engine or Satellite manifold). Water should always be shut down at the supply pumper.

B: When stretching supply line to the Tower Ladder, ensure the female end is stretched to the gated inlet; storing spanners and fittings in proximity to the gated inlet at the base of the Tower Ladder will increase unit efficiency when transitioning to an LCS operation.

C: To maximize the efficiency of the Tower Ladder, if possible, two sources should generally be employed to supply the bucket.

D: The recommended pressure at the Tower Ladder nozzle for an effective operation should be 200-250 psi.

Answer 15

A
Explanation:
TOWER LADDERS – CHAPTER 4
A – Correct – 4.1
B – Incorrect – Ensure the male end is stretched to the TL
C – Incorrect – Generally, one supply source at the base of the tower ladder should be used. 4.1
D – Incorrect – Recommended pressure at the gated inlet should be 200-250 psi.

Question 16

Certain components of the tower ladder require inspection by the members to ensure serviceability. Which of the following regarding inspection times is CORRECT?
A: Condition of the safety belts installed in the bucket is conducted each tour.

B: A visual check of the condition or presence of the clip/nut at the end of each boom section is done daily.

C: A visual check of the compression and tension bolts at the turntable 5th wheel shall be made monthly.

D: A test of the electrical outlets at the bucket and lights is conducted each tour.

Answer 16

B
Explanation:
TOWER LADDERS CHAPTER 7 – INSPECTION
A – Incorrect – Safety belt inspection is DAILY
B – Correct –Clip/nut at the end of the boom sections is inspected DAILY
C – Incorrect – Turntable 5th Wheel is inspected during MUD at operations or in quarters Pg 2.
D – Incorrect – Electrical outlets at the bucket and lights is conducted daily.

Question 17

Pictures are a part of the testing process as well and are fair game when writing exams. According the picture associated with ventilating a peaked roof private dwelling, there are a series of cuts made in a sequential order. Which cut is the first cut made perpendicular to the ridge pole in the illustration?
A: 1st cut

B: 2nd cut

C: 3rd cut

D: 4th cut

Answer 17

C
Explanation:
TOWER LADDERS – CHAPTER 3
C is correct – The 3rd cut is perpendicular to the ridge pole. Ch 3 3.5 figure 1.

Question 18

Tower Ladder 99 is assigned to a box where they are tasked with removing an injured construction worker via stokes basket from the upper floors of a building. TL positioning is as important as the manner in which the stokes is secured to the bucket. Which of the choices below CORRECTLY indicates the preferred positioning of the stokes basket along with the proper placement of the apparatus in relation to the building?
A: The preferred positioning of the stokes is in a horizontal position and the apparatus should be positioned so that the center line of the turntable is at least 25-30’ from the building.

B: The preferred positioning of the stokes is in an upright position and the apparatus should be positioned so that the center of the turntable is at least 25-35’ from the building.

C: The preferred positioning of the stokes is in a downward position and the apparatus should be positioned so that the center of the turntable is at least 25-35’ from the building.

D: The preferred positioning of the stokes is in a diagonal position and the apparatus should be positioned so that the center of the turntable is at least 25-30’ from the building.

Answer 18

D
Explanation:
D is Correct – Diagonal positioning is the preferred as it is the easiest and safest of the three options. The apparatus should be positioned so that the center line of the turntable is at least 25-30 feet from the building. Chapter 3 3.3

Question 19

Tower Ladders discusses a two member tactical approach at fire operations. Which of the following is INCORRECT about this approach from the tower ladder bucket?
A: When the ladder company members make the decision to operate in this manner, the incident commander should immediately be notified.

B: One member remaining in the bucket to act as a beacon to monitor, ventilate, assist in rescue and establish a valuable communications link to the Incident Commander is an overall tactical advantage.

C: It is essential for the bucket firefighter to maintain radio contact with the member conducting a search of the fire area.

D: If a known life hazard is discovered and immediate action could prevent the loss of life, appropriate action may be taken consistent with the provisions stated in FFP Safety Team.

Answer 19

C
Explanation:
A, B, D are Correct Chapter 3 3.1 pg 2
C is Incorrect – It is essential for the bucket firefighter to maintain voice contact with the member conducting a search.

Question 20

Members of Tower Ladder 99 were having a round table discussion about positioning the bucket for removals during fire operations.Which statement below is the only CORRECT one made regarding bucket positioning operations?
A: When preparing to move a properly positioned bucket from a window, the first joystick movement should generally be opposite its preceding movement.

B: Positioning the apparatus parallel to the objective and lining up the turntable with the window will shorten the horizontal travel distance, reduce the time required to reach the target, and ensure an angular approach.

C: The preferred position for the removal of Unconscious, incapacitated, or obese victims is to position the middle bucket rail level with the window sill or top rail of the fire escape.

D: Position the top of the bucket at a level where a person can easily step into it without straddling the window sill or fire escape railing.

Answer 20

A
Explanation:
TOWER LADDERS – CHAPTER 3
A is Correct 3.3
B – Incorrect – Line up the bucket with the objective. 3.3
C – Incorrect – The preferred position for unconscious, obese, incapacitated victims is the top bucket rail level with the window sill or top rail of the fire escape. 3.3
D – Incorrect – Position the middle of the bucket at a level where a person can easily step into it without straddling the window sill or fire escape railing 3.3

Question 21

Bucket safety has become a high priority for members operating in tower ladder companies. Ladder 99 held a drill following roll call to address issues related to the bucket in compromised positions. Which statement made by members was CORRECT regarding these operations?
A: If no other option is available and members must use the escape ladder to exit the bucket, the apparatus shall be taken out of PTO, shut down, and the escape ladder side rails raised.

B: If the bucket becomes stuck or wedged, the members in the bucket should depress the EAB button and transmit an urgent message to the Incident Commander.

C: If the bucket becomes stuck or wedged, the members shall remain low in the bucket and the LCC should take over all bucket movement until the condition is corrected.

D: If the bucket becomes stuck or wedged, the apparatus should be taken out of PTO and shut down.

Answer 21

B
Explanation:
TOWER LADDERS – CHAPTER 3
B is Correct – 3.6 pg 7
A – Incorrect – The apparatus shall remain in PTO & shut down. 3.6
C – Incorrect – Members shall remain low, the apparatus shall be shut down. 3.6
D – Incorrect – The PTO shall remain engaged. 3.6

Question 22

Tower Ladder 99 is responding first due to a working fire on the fourth floor of a six story H type Multiple Dwelling. The building is 200x200, has two large wings with wing stairs separated by a throat and there are two fire escapes present on the front of both wings. The first arriving engine reports fire out two windows off the far end fire escape near the exposure 2 wall in the A wing. Based on this information, which choice is CORRECT regarding the recommended initial positioning Ladder 99 should take on arrival?
A: Position at the front of the building with the bucket positioned to cover the throat.

B: Position to cover the fire apartment/floor above for VEIS and secondary egress.

C: Position to allow the aerial access to the roof of the fire building.

D: Position to provide roof access for the 1st & 2nd arriving roof firefighters.

Answer 22

B
Explanation:
TOWER LADDERS – CHAPTER 2
B is Correct – Additional Tower Ladders shall be positioned to cover the throat. 2.1.4
A – Incorrect – Initial Throat positioning for top floor fires 2.1.4
C – Incorrect – Not stated
D – Incorrect – Not stated – TL not primary means to access the roof in H-type MD’s

Question 23

Which of the following choices is CORRECT regarding the use of the Tower Ladder Bucket?
A: The controls at the pedestal allow for smoother positioning than the joystick controls. The pedestal firefighter should always perform delicate movements.

B: All jacks and outriggers must be fully lowered whenever the Tower Ladder Bucket is to be used.

C: Detailed members should not operate on the turntable unless they are assigned to a truck company, are a qualified Chauffeur, or Company trained FF assigned to a TL.

D: The pedestal firefighter should relay operational and safety concerns received from the bucket to the company officer.

Answer 23

B
Explanation:
TOWER LADDERS – CHAPTER 1 – PG 6
A – Incorrect – Exception is when pedestal firefighter’s view is obstructed.
B - Correct 1.2 PG 6 Bottom
C – Incorrect – Tower Ladder Company firefighter and NOT Company trained.
D – Incorrect – Incident Commander should be notified

Question 24

Water delivery via Tower Ladder at a fire is a major factor in the success of an operation. Which water delivery strategy is INCORRECT according to Large Caliber Stream delivery from a Tower Ladder?
A: At an advanced Row Frame fire where multiple floors are involved, LCS delivery should begin at the lowest level and work its way up to the top floor and cockloft area.

B: For common cockloft protection, commence LCS attack at the leading edge of the building and traverse towards the middle to facilitate extinguishment.

C: At H-types with fire showing out windows in the front, courtyard, and throat, the TL stream should be directed at the windows in the throat first, then advanced toward the front of the building, and finally into the front windows.

D: A street level attack at a taxpayer fire using the LCS to penetrate the ceiling and collapse it, thereby exposing fire in the cockloft, enables extinguishment of fire therein.

Answer 24

A
Explanation:
TOWER LADDERS – CHAPTER 4
A – Incorrect – The exception is -- At an advanced fire in a Row Frame, begin application at the top floor and into the cockloft. 4.2 bottom
B – Correct – 4.2 Bottom
C – Correct 4.2 pg 3 Bottom
D – Correct – 4.2 pg 3 Bottom.

Question 25

Positioning a tower ladder on a hill has always been a tricky proposition. Which choice below is MOST CORRECT regarding positioning of the apparatus when operating on a hill?
A: Position the apparatus parallel to the slope facing downhill, turntable before the objective.

B: Position the apparatus parallel to the slope facing uphill, turntable past the objective.

C:✔Position the apparatus parallel to the slope facing downhill, turntable past the objective.

D: Position the apparatus parallel to the slope facing uphill, turntable before the objective.

Answer 25

C
Explanation:
TOWER LADDERS CHAPTER 2
C is Most Correct – Position the apparatus parallel to the direction of the slope so that boom operations will be in the uphill direction. If possible, the apparatus should be facing downhill (e.g. if facing downhill, place the turntable past the objective) 2.4 pg 19

Question 26

Scrub Area is an important feature of tower ladder positioning. A properly positioned tower ladder can cover how many Brownstone type Row-Frame buildings?
A: 7

B: 6

C: 5

D: 4

Answer 26

B
Explanation:
TOWER LADDERS – CHAPTER 2 B is Correct – 2.1.2 & Photo

Question 27

Lt. Tenon is working in Tower Ladder 199 and her unit is assigned to a breaching operation at a stubborn fire in a commercial building. Which action taken by the truck company is CORRECT according to the TL bulletin?
A: Members were assigned to breach cinder block windows and started at the middle where the wall was weakest and hollow to provide quick access.

B: Cuts in brick walls shall be triangular with the vertex angle downward to prevent further collapse.

C: The first cuts shall be at the mortar since this is the easiest part of the cuts and the blade will not be worn at this point.

D: On two course brick walls, the second course can be removed by hand tools, or if a heavy stream will be used by the stream itself.

Answer 27

D
Explanation:
TOWER LADDERS – SPECIAL SITUATIONS – CHAPTER 6
A – Incorrect – Start at the top as this area is usually hollow 5.2
B – Incorrect – Vertex angle upward to prevent further collapse. 5.2
C – Incorrect – The first and second cuts shall be at the brick and concrete since the easiest cut is at the mortar joint and the blade at this point will be worn.5.2
D – Correct – 5.2 pg 2.

Question 28

Initial positioning of the apparatus is a mark of a company’s professionalism & often is a determining factor in the success at an operation. Which choice below is INCORRECT according to the recommended initial tower ladder positioning guidelines?
A: At a fire on the 3rd floor of a 4-story brownstone, the initial apparatus positioning of the tower ladder would be for top floor VEIS.

B: At a fire on the 4th floor of a 5-story tenement, the initial positioning of the tower ladder would be to the fire apartment/floor above or off window of the fire escape.

C: At a taxpayer with fire extending to exposures, the initial positioning of the tower ladder would be to operate at roof level and protect exposures.

D: At a top floor fire in an H-type multiple dwelling, positioning a tower ladder in the throat can dramatically influence an operation.

Answer 28

C
Explanation:
TOWER LADDERS – CHAPTER 2
A – Correct – 2.1.1
B – Correct 2.1.3
C – Incorrect – Position to operate at street level and protect exposures
D – Correct – 2.1.4.

Question 29

Arriving as the extra truck at a fire involving a large 2 ½ story private dwelling, Tower Ladder 90 is tasked with ventilating the peaked roof. Which choice below is CORRECT regarding this operation?
A: The tower ladder bucket should be positioned on the roof as close to the ridge pole as possible.

B: The saw operator shall wear the installed safety belt or the LSR tied with a bowline to the bucket railing to allow maneuverability.

C: The saw shall be started outside the bucket and held outside the bucket until it is shut off.

D: The saw operator shall make the first cut perpendicular to the ridge pole. The size of the cut will depend on the reach of the operator.

Answer 29

A
Explanation:
TOWER LADDERS CHAPTER 3
A is CORRECT 3.5
B – Incorrect – LSR tied to a substantial part of the bucket. Bucket railings are not a substantial pare of the bucket and shall not be used as a substantial object when tying off. 3.5 -1
C – Incorrect – Saw shall be started inside the bucket and held outside until shut off. 3.5 -2
D – Incorrect – Make the first cut parallel to the ridge pole 3.5 -3

Question 30

Anytime a Tower Ladder is set up, supplied, and placed into operation, Safety remains on the front burner. Which choice below regarding operations is INCORRECT?
A: The pedestal firefighter must don PPE and be continuously aware of changing fire conditions. This member should have a working knowledge of the location of other operating units.

B: The pedestal firefighter shall activate the platform control switch and/or Safety Interlock Foot Pedal during overhaul and whenever members or civilians enter or leave an elevated bucket to prevent accidental movement.

C: The member operating the joystick should preplan bucket movement in the event of an imminent or actual collapse. When operating at upper floors, this will generally be upwards.

D: When collapse is feared, the height of the wall vertically above the bucket is the minimum distance horizontally that the bucket should be away from the wall.

Answer 30

B
Explanation:
TOWER LADDERS – CHAPTER 4 – LARGE CALIBER STREAM OPERATIONS
A – Correct – 4.3 bottom
B – Incorrect – Consider activating the platform control switch… 4.3
C – Correct 4.3 pg 5
D – Correct 4.3 pg 4 bottom

Question 31

On a cold winter night, the members of Ladder 199 were discussing Tower Ladder operations as the snow piled up deep on the city streets. Which statement below made by the members is CORRECT regarding these operations?
A: If operations are to remain stationary in freezing weather, the boom should periodically be rotated to the left and right to prevent ice build-up.

B: When conditions warrant, Department issued snow chains shall be mounted on both front and four rear outer drive-wheel tires.

C: During extreme cold weather, the incident commander should facilitate periodic relief of members operating in buckets to prevent overexposure to the elements.

D: Clear snow prior to setting jacks/outriggers to verify stabilizers aren’t being lowered on vaults/manholes. Use rock salt or speedy dry under and around jack and outrigger pads to prevent slipping.

Answer 31

D
Explanation:
TOWER LADDERS CHAPTER 6 – SPECIAL SITUATIONS
A – Incorrect – Extend and Retract boom to prevent ice build-up 5.5
B – Incorrect – Not front tires. Just four rear outer drive-wheel tires. 5.5 pg 4
C – Incorrect – Tower Ladder Officer should facilitate periodic relief. 5.5 pg 4
D – Correct 5.5 pg 3 & 4.

Question 32

Tower Ladder 199 arrives first due at a trench collapse and is in prime position to be used as a high point anchor to assist with SOC operations. Which of the following regarding the set up and use of the TL is CORRECT?
A: The Tower Ladder can support at least 1000 lbs. The preferred location for the high point anchor is under the bucket.

B: The landing pads under the bucket are suitable for securing anchor straps for the high point.

C: Remove all members from the apparatus and disengage the PTO once the apparatus is in position.

D: Once secured to the metal stokes, the TL can be used in extreme circumstances to lift the patient.

Answer 32

A
Explanation:
TOWER LADDERS – CHAPTER 6 SPECIAL SITUATIONS
A – Correct – 5.4 & confined space 4.4 pg 7.
B – Incorrect – UNDER NO CIRCUMSTANCES shall the landing pads be used as a high point anchor.
C – Incorrect – Remove all members, turn the siren to on and turn the apparatus to the off position. 5.4
D – Incorrect – UNDER NO CIRCUMSTANCES should a tower ladder be used as a crane to lift a patient.

Question 33

Capt. Smith was discussing the application of snow chains with his members. He was correct in all but which point below?
A: When snow chains are applied to an apparatus, that vehicle should not exceed 30 MPH.

B: When the weather conditions and weather improve, the chains must be removed.

C: When returning from an alarm; if the snow chains break, the officer shall cause the vehicle to stop immediately and have the conditions corrected.

D: When required, members shall install the snow chains on the apparatus. The turtle ramp shall be used only if the “drive over” method is not possible.

Answer 33

D
Explanation:
A-Training Bulletins, Apparatus C-2, sec. 2
B-sec. 2
C-sec. 2, anytime not responding
D-Add #1 sec. 2 can be used as an alternative

Question 34

Which of the following choices below is not in accord with PAID 2-2019, the FDNY Lactation Policy?
A: A lactation room is a sanitary place that is shielded from view and free from intrusion

B: A lactation room includes an electrical outlet and a chair

C: Employees who submit a “Request for an Accommodation to Express Milk” form to the EEO office, shall do so no later than 14 days before they plan to express milk

D: Lactation rooms may never be used for any other purposes when the lactating employee is on duty

Answer 34

D
Explanation:
A. sec. 2.3
B. sec. 2.3
C. sec. 3.2
D. PAID 2-2019  sec. 3.4.3 
they can be used for other purposes, except while the employee is expressing milk.

Question 35

If a pregnant firefighter believes that they are incapable of performing the duties of a full duty member, they must provide the Bureau of Health Services (BHS) with written verification from the member’s health care provider. The member will be placed on light duty by BHS upon the member’s request. Which point below is a most accurate description in regards to the firefighters on light duty?
A: These firefighters shall report to the quartermaster to procure work-duty uniforms that are appropriate for pregnant members.

B: Pregnant Full-duty members may modify their uniform.

C: If on light duty and wearing a modified uniform, a pregnant FF shall display an FDNY identification card on their clothing.

D: The FDNY Identification card displayed by a light duty FF in a modified uniform shall not be displayed on their jacket/coat. It shall be attached to their shirt/sweater.

Answer 35

C
Explanation:
A-PAID 1-89, sec. 2, they may modify light duty uniform with business appropriate attire.
B-PAID 1-89 does not mention uniforms for pregnant full-duty members.
C-PAID 1-89 sec 2.2
D-PAID 1-89, sec 2.2, it only says displayed on outermost garment, so if they are wearing a jacket it goes on the jacket. If they remove the jacket, it goes on whatever is the new outermost garment.

Question 36

Lt. Wendy was correct when she stated that the on-duty firefighters shall wear the long-sleeve-work-duty shirt beginning on which date each year?
A: October 1st.

B: November 1st.

C: October 31st.

D: November 30th.

Answer 36

B
Explanation:
B-Regs Ch 29, sec 29.6.4

Question 37

The Maxiforce airbag system is a valuable tool in rescue and extrication operations. When inflated with air, they are designed to lift and move heavy loads. They are relatively simple to assemble and operate, requiring only an inch of space for insertion. In addition to the above information, all of the following statements contain correct information in regards to the Maxiforce airbag system except?
A: With vehicles, the airbags can be used in lifting the steering columns, doors, a door post, pedals or the dashboard

B: There are 7 bags in the system, ranging from a 12 ton bag (the smallest) to a 74 ton bag (the largest)

C: A light reflective label on one side of the bag shows its maximum tonnage and lifting height. Units should paint the lift capacity and lift height on the bags in addition to the label

D: Only Steel SCBA cylinders are used to operate the air bags, except during drill; an aluminum SCBA may be used

E: Set the low pressure gauge to 135 psi.

F: When the high pressure gauge falls below 200 psi, change the air cylinder

Answer 37

D
Explanation:
Training Bulletins Tools 20 
A- 1.2....New: Dept Order 108/2019 (11/20/2019)
B- 2.1.1
C- Only steel SCBA cylinders are to be used to operate...sec 2.5.1
D- 3.1.4
E- 3.1.4.note

Question 38

During the 6x9 tour in the great Borough of the Bronx, the ladder company you are working in has just been activated as a Rapid Response Vehicle Task Force (RRV) due to a major blackout. As you turn out, you are trying to remember all the protocols of the RRV. Choose the incorrect protocol.
A: The initial Task Force may consist of an officer serving as a TASK Force Leader, 3-6 FFs ,and 2 apparatus

B: The second piece of the SOC Support Ladder that is equipped with an MDT, will be identified in the CADS system as RRV. For example, RRV027

C: When more than one task force is assembled, a Sector/ Group Supervisor shall be assigned

D: The primary method of communications shall be the DARS radio

Answer 38

B
Explanation:
AUC 159 add 8…New as of 11/20/2019 (Dept Order 108/2019)
A-3.2
B- “R” R027…..this is only for the 2nd pieces with an MDT. 2nd pieces without MDT will be called on dept radio as SOC Support Ladder, for example SSL-50…..sec 3.2.3
C- sec 3.5
D- Primary- DARS, Alternate- 800 MHZ, Emergency- Dept Radio……when DARS, 800 MHz, and Dept radio are OOS, then the contingency communication is the cell phone….NEW (this changed) sec 4.1
THIS IS A MUST READ. Several changes to this bulletin

Question 39

The Blitzfire Oscillating Monitor is an efficient, compact and easy to maneuver portable monitor. Choose the incorrect information about the Blitzfire.
A: The Blitzfire is designed for a maximum inlet pressure of 175 psi

B: The Blitzfire has a pivoting inlet and a pivoting outlet, both of which have 2 1/2” FDNY thread.

C: The Blitzfire monitor is provided with a 2 1/2” dual pressure automatic fog nozzle. It can also be operated with solid stream stacked tips (1 1/4” and 1 1/2” tips only)

D: The Blitzfire 2” solid stream tip shall only be used in an emergency in consultation with the IC

Answer 39

D
Explanation:
2” solid stream tip should not be used with the Blitzfire monitor due to poor stream reach and stream break up
Training Bulletins Tools 38 sec 7.5

Question 40

When removing a windshield during a vehicle extrication, the four tools that can be used include all of the following except?
A: Windshield saw

B: Sawzall

C: Beluga knife

D: Circular saw with wood cutting blade

Answer 40

D
Explanation:
Axe is the 4th tool (used as a last resort)
The Beluga knife was added recently to this bulletin (11/12/2019)
Emergency Procedures Vehicle Disentanglement sec 11.3