TB 69 MAXI-FORCE AIR BAG Flashcards
TB 69 MAXI-FORCE AIR BAG
A. One dual “dead man” safety relief and control valve
B. One high pressure regulator
C. Three in line safety relief valves
D. Four air hoses (red, yellow, green and blue)
E. Three air lifting bags (2 - 22 ton, 1 - 12 ton)
F. One air supply adapter
G. Cribbing
reference
TB 69 MAXI-FORCE AIR BAG
High Pressure Regulator
Adjust pressure between ___-___ psi, to provide 118 psi working pressure at the dual safety relief and control valve. When attaching to the SCBA bottle, the last ___ turn should be accomplished by turning both the threaded inlet fitting and regulator together until hand tight.
125-135
1/4
TB 69 MAXI-FORCE AIR BAG
In-Line Safety Relief Valve
Relieve if pressure exceeds ____ psi.
135
TB 69 MAXI-FORCE AIR BAG
Each hose is ___ feet long,
with a working pressure of ___ psi.
Each of the air hoses is equipped with a male and female “quick-disconnect” fitting and safety lock ring. (These fittings are made of brass and may crack if the bag rolls onto fitting.)
16
250
TB 69 MAXI-FORCE AIR BAG
Air bags are constructed of neoprene rubber compounds encasing kevlar cords
reference
TB 69 MAXI-FORCE AIR BAG
The adapter allows for an auxiliary air source to be used such as:
- Apparatus On-Board Air System
- Portable Air Compressor
NOTE
It can also be used to extend a hose length (i.e., air chisel hose to air bag hose):
reference
TB 69 MAXI-FORCE AIR BAG
The cribbing provided should be considered a minimum:
- 4”X6”X2’ (___)
- 24”X24” Plywood (___)
- Wedges (___)
(4)
(2)
(4)
TB 69 MAXI-FORCE AIR BAG
Do not inflate the bag over ___ psi without a load.
30
TB 69 MAXI-FORCE AIR BAG
2 bag life
Larger bag on bottom
Inflate/Deflate one bag at a time
Inflate bottom bag then top bag (1 inch then the other 1 inch alternating)
Air lines to opposite corners
reference
TB 69 MAXI-FORCE AIR BAG
Never inflate air bags against objects hotter than ___ degree F.
220
TB 69 MAXI-FORCE AIR BAG
When stabilizing a vehicle, chock a minimum of one front wheel and one rear wheel on each side.
reference
TB 69 MAXI-FORCE AIR BAG
-Small cuts on the neoprene surface can be repaired with rubber cement.
reference
TB 69 MAXI-FORCE AIR BAG
-To leak test a bag:
Inflate bag to ___ psi. Place inflated bag into water or a soap-solution. If bubbles appear, this indicates a leak. If bag leaks, it must be forwarded to the Supply and Maintenance Division for repair.
DISREGARD bubbles around the bag inlet, it will not affect the safe operation of the bag.
30
TB 69 MAXI-FORCE AIR BAG
K-12 Air Bag
a. Size: ______”
b. Maximum Lifting Capacity: 12 tons at 118 psi
c. Maximum Lifting Height: __”
d. Maximum Air Capacity: ___ Cubic Feet of Air
e. Weight: __ Pounds
f. Inflation Time: __ Seconds
g. Bag is tested at ___ psi and bust tested at ___ psi.
a. Size: 7/8”X15”X15”
b. Maximum Lifting Capacity: 12 tons at 118 psi
c. Maximum Lifting Height: 8”
d. Maximum Air Capacity: 3.0 Cubic Feet of Air
e. Weight: 6 Pounds
f. Inflation Time: 3 Seconds
g. Bag is tested at 236 psi and bust tested at 700 psi.
TB 69 MAXI-FORCE AIR BAG
This maximum lifting capacity is from 0” to 1”.: The higher the lift, the less lifting capacity
reference