World Transmission Operations Flashcards
Transmission T-handle range selector ______ to ______
06’-16’
When all segments of the display are illuminated for more than ___ seconds, the ECU did not complete initialization
12
When the display shows a “______ ______” symbol, a selector-related fault code has been logged
Cat Eye
Digital display Pierce: Select display (upper) - ______ available gear
Highest
Digital display Pierce: Monitor display (lower) - ______ available forward range
Lowest
Shift selector has ______ locked positions to prevent accidentally selecting N, R, D
Three
MODE button - LTI & Pierce: to access ___th gear
5
Display flashing - if display shows ___ or ___ and is flashing an inhibit function is preventing the range selection which indicates vehicle condition is preventing the shift from occurring
R D
When the ______ ______ is illuminated steady or flashing during normal operation, service is due
Service Icon
Transmission will not shift into range if ______ ______ code is active
CHECK TRANS
Transmission push button range selector ____ - ____
00’-03’
If the apparatus has a T handle range selector the vehicle will not start unless ___ has been selected
N
World Transmission Operations:
Under full acceleration ____% pedal travel, trans shift pints occur at approximately ____ RPM
100
2100
First gear range (1) used for pulling through _______
Muddle
First gear range (1) provides max ______ power & engine ______ power
Driving
Braking
When making shift be sure to alway select __ when transitioning from reverse to a forward range & visa versa.
N
LTI 96’-03’ TRANSMISSION SPEED RANGE;
1st gear @ 2100 RPM ___ MPH
15
LTI 96’-03’ TRANSMISSION SPEED RANGE;
2nd gear @ 2100 RPM ___ MPH
23
LTI 96’-03’ TRANSMISSION SPEED RANGE;
3rd gear @ 2100 RPM ___ MPH
33
LTI 96’-03’ TRANSMISSION SPEED RANGE;
4th gear @ 2100 RPM ___ MPH
53
LTI 96’-03’ TRANSMISSION SPEED RANGE;
5th gear @ 2100 RPM ___ MPH
68
LTI 06’-09’ TRANSMISSION SPEED RANGE;
1st gear @ 2100 RPM ___ MPH
14
LTI 06’-09’ TRANSMISSION SPEED RANGE;
2nd gear @ 2100 RPM ___ MPH
26
LTI 06’-09’ TRANSMISSION SPEED RANGE;
3rd gear @ 2100 RPM ___ MPH
35
LTI 06’-09’ TRANSMISSION SPEED RANGE;
4th gear @ 2100 RPM ___ MPH
50
LTI 06’-09’ TRANSMISSION SPEED RANGE;
5th gear @ 2100 RPM ___ MPH
68
Pierce transmission shift selector features:
__________
__________
__________
__________
__________
Diagnostics
Transmission Health (clutch life)
Filter life
Oil life
Oil level
Pierce Oil Life Monitor: press the display mode/diagnostics ______ times, the oil life stars is displayed as a _________ of remaining life
Two
Percentage
To reset the Oil Life Monitor: when in Oil life monitor mode, press and hold the mode button for ___ seconds OR shift the gear ranges in the following sequence (do not pause for more than ___ seconds)
___-___-___-___-___-___-___
10
3
N-D-N-D-N-R-N
Pierce Filter Life Monitor: press display mode/diagnostics ______ times, the filter status is displayed as “______ _______” or “______ ______”
Three
Filters OK
Replace Filters
To reset the Filter Life Monitor: when in filter life monitor mode, press and hold the mode button for ___ seconds OR shift the gear ranges in the following sequence (do not pause for more than ___ seconds)
___-___-___-___-___-___-___
10
3
N-R-N-R-N-D-N
Pierce Transmission Health Monitor: press display mode diagnostics ______ times, the ransmission health is displayed as “___” or “____” if “____” is displayed then clutch maintenance is required.
Four
OK or LO
LO
Pierce Transmission Health Monitor can only be reset using the ______ _____ factory scan tool
Allison DOC
Diagnostic Codes: consist of ___ digit main code & ___ digit sub code
Two
Two
Diagnostic Codes: are logged in a list in the trans ECU memory with the most severe or otherwise most recent code listed ______.
First
06’-09 enter diagnostic mode by pressing mode button ______
Twice
16’ pierce enter diagnostic mode by pressing mode button ______
Five
00’-03’ enter diagnostic mode by pushing ⬆️ & ⬇️ arrows together ______
Twice
Exiting Diagnostic Mode 95’-03 - hold MODE button for approximately ___ seconds and resume operations
10
Exiting Diagnostic Mode 06’-09’ - hold ___ seconds to clear active codes & resume operation
3
Exiting Diagnostic Mode 16’ Pierce - press diagnostics button momentarily until range display appears, will self terminate after ___ min of inactivity
10
Transmission Fluid: fire trucks are difined as severe service and should be changed
______ miles
______ months
______ hours
12,000
6
500
Checking Fluid Level: & 06’-09’ press the display button or ⬆️&⬇️ button _____
Once
High fluid level: will be indicated by a “____” represented by a ___. 06’-16’ will be indicated by a ___
HI
01
1
Conditions Necessary to use digital readout to display fluid level: engine is at idle (Below ______ RPM)
1,000
Conditions Necessary to use digital readout to display fluid level: fluid temp must be above ___ ° F & below ___° F
140
220
World Transmission Operations:
Conditions Necessary to use digital readout to display fluid level: apparatus has been stationary for approximately ___ minutes to allow the fluid to settle
Two
Manual hot trans fluid check: fluid at operating temp of ( ____ °F - ____°F)
160-200
World Transmission Operations:
Manual hot trans fluid check: start and run engine at idle ___ to ___ RPM
500 to 800
Cold Check 06’-16’ - fluid temp is ___°F - ___°F
60 -120
Pierce trans operating temp: max sump operating temp is ___°F
250
