2006-2009 American LeFrance Log Book Flashcards
06’-09’ ALF Log Book: Info contained in this operation manual will assist in ________ _______ _______
Operation
Maintenance
Troubleshooting
06’-09’ ALF Log Book: Is divided into ___ sections ______ ______ ______ _______ _______
5
Introduction
Driving & Controls
Aerial Operations
Maintenance
Record
06’-09’ ALF Log Book: supply and maintenance division at ___ ___ ____?
213-485-6111
06’-09’ ALF Log Book: What are the three types of headings?
Danger
Caution
Note
06’-09’ ALF Log Book: Equipped with a computer-controlled (4) _____ _____ _____ _____.
Engine
Transmission
Anti-Lock Braking System (ABS)
Electrical Load Management System(Load Manager)
06’-09’ ALF Log Book: Each ECU (Electronic Control Unit) controls (3) ______ ______ ______
Program
Diagnostic Capabilities
Safety Features
06’ ALF Log Book: Height (max) top of tiller cab ____?
11’1”
09’ ALF Log Book: Height (max) top of tiller cab ____?
11’3”
06’-09’ ALF Log Book: Height top of cab roof ___?
10’
06’-09’ ALF Log Book: Height Cab Full Tilt Position ____?
15’6”
06’ ALF Log Book: Length ___? 09’ ALF Log Book: Length ___?
55’2”
54’6”
06’-09’ ALF Log Book: Width (Including Mirrors) ____?
9’5”
06’-09’ ALF Log Book: GVWR (Gross Vehicle Weight Rating) ________?
65,500 lbs
06’-09’ ALF Log Book: GAWR (Gross Axle Weight Rating) Front Axle ____?
20,000 lbs
06’-09’ ALF Log Book: GAWR (Gross Axle Weight Rating) Rear Axle ____?
24,000 lbs
06’-09’ ALF Log Book: GAWR (Gross Axle Weight Rating) Tiller Axle _____?
21,500 lbs
06’-09’ ALF Log Book: Apparatus Average Weight (Fully Loaded w/ Personnel) _______?
60,090 lbs
06’-09’ ALF Log Book: Apparatus Average Weight (Front Axle) ______?
15,910 lbs
06’-09’ ALF Log Book: Apparatus Average Weight (Rear Axle) ______?
22,370 lbs
06’-09’ ALF Log Book: Apparatus Average Weight (Tiller Axle) _____?
21,810 lbs
06’-09’ ALF Log Book: Ground Jack Spread-Fully Deployed ____?
14’
06’-09’ ALF Log Book: Apparatus Normal System Voltage ____ - ___ Volts
12.9 - 14.4
06’-09’ Engine Oil Pressure Normal ___ psi min @ idle ___ to ___ psi @ rated
10 30 to 45
06’-09’’ ALF Log Book: Engine Coolant Temp ___° to ___° F Max. ___°F
190° To 208° 219°
06’-09’ ALF Log Book: Engine Fan Clutch Engagement ___°F @ Idle with parking brake set.
208°
06’-09’ ALF Log Book: Transmission Fluid Temp. ___° to ___°F & ___ to ___ Oper
140° to 220° 160° to 200° Operating
06’-09’ ALF Log Book: Air Brake Normal Operating Range ___ to ___ PSI
90 - 120
06’-09’ ALF Log Book: Fuel Tank Capacity ___ Gallons
65
06’-09’ ALF Log Book: Fast Idle ____ - ____ RPM
1,500 - 1,600
06’-09’ ALF Log Book: Emergency Power Unit (EPU) Pump ___ GPM @ ____ PSI
1.5 @ 2000
06’-09’ ALF Log Book
Onan Generator OPS Ranges: Engine Oil Pressure ___ - ___ PSI @ Opper Temp.
28-64
06’-09’ ALF Log Book
Onan Generator OPS Ranges: Engine Coolant Temp ___° to ___° F
160° to 195°
06’-09’ ALF Log Book
Onan Generator OPS Ranges: Output ___ kW
7.5 kW
06’-09’ ALF Log Book
Onan Generator OPS Ranges: DC Voltmeter ___ - ___ Volts
12.5 - 15 Volts
06’-09’ ALF Hydraulic System Capacity: oil reservoir capacity ___ Gallons
40
06’-09’ ALF Hydraulic System Capacity: Hydraulic pump capacity ___ GPM
20
06’-09’ ALF Hydraulic System Capacity: Max system Pressure _____ PSI
2800
06’-09’ ALF Hydraulic System Capacity: Outrigger Relief valve setting _____ PSI
2000
06’-09’ ALF Hydraulic System Capacity: Hoist max pressure _____ PSI
2800
06’-09’ ALF Hydraulic System Capacity: Rotate max pressure _____ PSI
1500
06’-09’ ALF Hydraulic System Capacity: Extend/Retract max pressure ____ PSI
2000
06’-09’ ALF Hydraulic System Capacity: Lowering into cradle ___ PSI
800
06’09’ ALF Hydraulic System Capacity: Ground Jack Deployed Light Activation ___ PSI
800
06’-09’ ALF Aerial Ladder Dimensions: Elevation -___° to + ___°
-4° to +75°
06’-09’ ALF Aerial Ladder Dimensions: Retraction ____ Feet
31.8
06’-09’ ALF Aerial Ladder Dimensions: Extended ___ Feet
94
06’-09’ ALF Aerial Ladder Dimensions: Elevated Height ___ Feet
100
06’-09’ ALF Aerial Ladder Dimensions: Sections ____
4
06’-09’ ALF Voltage Monitor with Alarm activates when electrical system voltage drops below ___ Volts. Once activated, alarm will not deactivate until voltage increases by ___ Volt.
11.8 1
Radio switch located on a vertical panel behind the _________ _________ seat
Apparatus Operator
Radio switch controls power to ___________/____ radios & ____
Kenwood/800 MDT
Tun signal and headlight high beam lever: to activate the high beams, pull the lever ________ you until it “clicks”
Towards
To activate high beam “_______ _______” pull on the lever gently so that it does not travel to the click position.
“Flash to Pass”
06’-09’ ALF: Coolant temp gage ___ to ___
190° to 208°
06’-09’ ALF Aerial Ladder Dimensions: Windshield wiper switch slide the control knob all the way ______ for max delay between wipes
Down
06’-09’ ALF Aerial Ladder Dimensions: Windshield wipers, a second switch located on the steering column operates the ___ speed wipers switch
Two
06’-09’ ALF Aerial Ladder Dimensions: Air Cleaner Restriction Gauge max at Full-Load & governed RPM is ___ in. H2O, @ No-Load & governed RPM is ___ in. H2O
25
15
06’-09’ ALF: Battery Master Power MTD draws ___ TO ___ amps even when Battery Master switch is turned off
7 to 8
06’-09’ ALF Ignition switch: a “_______” style switch that when closed, allows current to flow to accessories.
Rocker
High idle switch raises the engine rpm to approximately _______-RPM
1,000
Normal Transmission temperature gauge range is ___° TO ___° F
160° to 200°
Engine coolant temperature gauge range is ___° TO ___° F
190° to 208°
Primary / Secondary Gauge:(Primary) brake circuit indicates pressure in the ______ axel
Rear
Primary / Secondary Gauge: (Secondary) brake circuit indicates pressure in the ______ axel
Front
Windshield washer switch activates the ______ washer pump
Electric
12 Volt on indicator light illuminates when the ignition switch is turned ___
On
Front Steady Light Switch activates the ___ red lights in the front grille
2
Rear Warning Lights Switch activates the 2 ______ warning on the rear of the trailer
Amber
Approaching Jackknife indicator light first buzzer ____° second buzzer ___° & buzzer will de-activate after passing each angle
65° 80°
Officer Information Center (OIC) is located on the __________ in front of the captain seat
Dashboard
Officer Information Center (OIC) displays (6)
______
______
______
______
______
______
Clock
Ambient Temp
Vehicle Speed
English/Metric units
Seat belt status
Event timers
Lock Out Cylinder Indicator Light illuminates when the lockout cylinder under the fifth wheel are _____
Deployed
06’-09’ ALF Low Oil Pressure/High Water Temp: illuminates when oil PSI falls below ___ PSI or water Temp, rises above ____°F
12 230°
06’-09’ ALF Brake system illuminates when air pressure falls below ___ - ___ PSI
65 - 75
06’-09’ ALF ______ ______ illuminates when there is a critical problem with the engine.
Engine Down
06’-09’ ALF _____ ______ illuminates when the cab latches are unlocked
Cab Lock
06’-09’ ALF Low Fuel illuminates when approximately ____ tank of fuel remains
1/8
Tiller Cab Heater Temp Control
Low ______ BTU
Medium ______ BTU
High ______ BTU
2,900
4,100
6,150
06’-09’ Caterpillar Engine Operations: C-___, ___-cylinder ______-in-head type engine
13 six valve
Caterpillar Engine Operations: ___” bore and a ____” stroke
5.12” 6.18”
Caterpillar Engine Operations: ___ cubic inches
763
Caterpillar Engine Operations: compression ratio of ___ to ___
17.0 to 1
Caterpillar Engine Operations: highest torque, ____-ft lbs @ ____ RPM
1650 @ 1800
Caterpillar Engine Operations: rated horsepower, ___ @ ____ RPM
525 @ 1800
Caterpillar Engine Operations: operating range is ____ to ____ RPM
1200 to 2100
Caterpillar - designed to run at lower RPM’s: Best Fuel economy between ____ - ____ RPM.
1200 - 1800
Caterpillar - designed to run at lower RPM’s: can run an additional ___% higher than max operating range
7
Starting Apparatus: if engine fails to start within ___ seconds, release starter button & allow starter to cool for ___ seconds before starting again. If fails to start after ___ attempts inspect to determine the cause.
15 15 4
Oil Pressure: Observe oil PSI immediately after starting, gauge should rest at least ___ PSI @ idle speed, if no pressure is indicated within ___-___ seconds stop the engine and check the lubrication system.
10 10-15
Oil Pressure: PSI should not fall below ___ @ ____ RPM & normal operating PSI higher
30 @ 1800
Throttle Pedal: Electronic foot pedal assembly was designed to communicate “_________” of foot pedal travel to the engine’s Electronic Control Module
Percentage
Idling: no longer than ___ min after ___ engage ______ ______
5 5 High Idle
Turbo: Try not to shut down unless coolant is ___°F or less
195
Electrical Load Managers: after battery voltage drops to approximately ___ Volts, engine throttle will be increased to compensate for low voltage & electrical system loads.
12.8
Electrical Load Managers: If the low-voltage continues for approx. ___ min, then the shedding of electrical loads will begin.
1
Electrical Load Managers: A shed system (load) will not be recognized for ___ minutes or until the unshed voltage setting is maintained for ___ minute.
5 1
Electrical Load Managers: The fast idle system will be maintained for a minimum of ___ minutes and until a voltage reading of ____ is achieved, even if any system shedding did not occur.
10 13.0
Electrical loads will turn on sequentially in priority order from ___ to ___ when their respective switch is activated
1 to 8
Load Manager - Fast Idle Output is dependent on ______ __________
Parking Break
Load Manager Toggle Switch
Electrical Load Managers: An alarm sounds if a lo-voltage condition (below ___ volts) develops & the OIC displays a message that the load manager system is in control.
11.9
Shed Voltage Sequence:
1) Air conditioning _____
Volts
12.7
Shed Voltage Sequence:
2) Spare ___ Volts
12.6
Shed Voltage Sequence:
3) Front warning & left scene ___ Volts
12.4
Shed Voltage Sequence:
4) Right Scene & Rear Scene ___ Volts
12.2
Shed Voltage Sequence; the first is air conditioning when voltage drops below ____ Volts
12.8
When all accessories are turned on & engine is running at idle ____ - ____ Rpm, the alternator is unable to keep up with electrical demand
500-750
At idle with ALL electrical accessories ON, system voltage can drop well below ____ Volts.
12.0
With high idle engaged with all accessories on system voltage will vary between ___ to ___ Volts.
12.9 to 13.1
When idling on scene, always engage _____ _____ feature. DEPARTMENT POLICY
High Idle
When “Emergency Master” switch is toggled “____”, Accessories will turn n in a delayed & sequential. Approximately _______ - ______ delays in sequence
ON Half-Seconds
Load Sequencing in half-second delays; ie & “reversed” when toggled off.
1. ________
2. ________
3. ________
4. ________
5. ________
6. ________
- Front light bar
- Front steady red lights
- Tiller light bar
- Rear amber lights
- Intersection lights
- High beam flash lights
Officer’s Information Center (OIC): Vehicle speed appears on a ___-digit LED display whenever the parking brake is not set.
3
Officer’s Information Center (OIC): message display is a ___ - digit LED display
16
When vehicle speed exceeds the values programmed into the OIC, the over speed warning indicator illuminates and a ______ sounds
Buzzer
Shoreline Power: when parked in quarters, plug power cord into “shore line power” receptacle located on ______ side of apparatus.
Left
Air-Kwik System: ASME certified water pressure tank rated at ___ PSI
200
Air-Kwik System: ___ Gallons
80
Air-Kwik System: constructed with #___ stainless steel for max. corrosion resistance
304
Air-Kwik System: never put _____ or any ______ solution in the tank as it could damage the stainless steel
Chlorine Salt
Air-Kwik System: powered by a high pressure (______ - ______) SCBA air cylinder
2216-4500
Air-Kwik System: cylinders are connected to the air delivery system by a ______ lined double braided stainless steel hose
Teflon
Air-Kwik System: only ___ cylinder needs to be opened for normal operation
1
Air-Kwik System: for max pressure for the entire 80 gallons ______ air cylinders should be turned on
Both
Air-Kwik System: discharge gate use to connect ___” firefighting line from water tank.
1”
Air-Kwik System: hose tray holds ___’ of ___” hose, in a tray located on both sides of the apparatus.
100’ 1”
Air-Kwik System: low water indicator, red light turns on when tank has approx. ___ gallons of water remaining
25
Air-Kwik System: tank pressure gauge displays static pressure when the discharge valve is closed (___-___ PSI)
0-300
Air-Kwik System: display PSI in air cylinder only when cylinder is turned on ___-___ PSI
0-5,000PSI
Air-Kwik System: regulator control knob typically set for ___-___ (___ PSI max)
150-175
200
Air-Kwik System: remove cover to service ____ V alarm battery
12
Air-Kwik System: fill cap ____” opening for added water concentrate.
1 1/2”
Air-Kwik System: automatic tank pressure relief valve ____ PSI
250
Air-Kwik System: full tank light (______). Low water warning light (______) goes on when tank level drops to approximately ___ gallons or less
Green
Red
25
Continue holding the switch in the raise position until the cab has reached the full tilt position approx. ___ °
50
If the cab will not lift make sure pump control knob on the lift pump itself is turned _______ until it stops
Clockwise
LOWER position until cab has settled on supports & continue to hold for another ___ seconds to insure cab locks are fully engaged
5
06’ ALF When checking brake travel, use a ruler or type measure from the brake chamber to the ______?
Clevis Pin
06’ ALF Service Brake Adjustment Check Procedure: If the distance measured exceeds ___” on the REAR BREAKS or the FRONT BRAKES, they’re out of adjustment & require immediate attention
2
06’ ALF Always be aware of the location of the _____ _____ _____ _____ & be sure to move away when the driver releases pressure on the Brake Pedal
Brake relay exhaust port
Brake Lining Inspection: The lining should not be less than ____ of an inch on either pad & not less the the steel _______ plate
1/4 backing
09’ ALF when the pads are new, the floating pin will be exposed approximately ___” to ___”
3/4” to 1”
09’ ALF When the pin is sticking out ___”, the pads are worn to replacement conditions. Call shops when sticking out ___”
1/4”
1/4”
To manually release the spring brake chamber, unscrew the ___” diameter bolt located at the end of the spring brake chamber utilizing a ___” box end wrench or socket
1/2 3/4
Place the “___” shaped end of the bolt into the hole located on the front of the brake chamber, turn the bolt ___ of a turn to lock it in place
T 1/4
BATTERIES: observe and note the condition of the battery maintenance “____”. It must register a “_____” color. Any other indicates a malfunctioning battery.
EYE GREEN
BATTERIES: always disconnect the ________ terminal first
Ground
BATTERIES: when connecting, always connect the ______ terminal last.
Ground
BATTERIES: Batteries give off ________ gas, which is highly explosive.
Hydrogen
BATTERIES: Wear safety ________ & protective _______ when working around batteries
Goggles Clothing
JUMP STARTING: The apparatus has a ___V negative ground electrical system. Make sure booster vehicle i also a ________ ground system
12 Negative
JUMP STARTING: To avoid damage to vehicle electronic components, voltage supplied to a vehicles electrical system must not exceed ___ Volts
16.0
JUMP STARTING: When jumping the battery, make sure the frame of the disabled vehicle is at least ___ inches from the battery
18
JUMP STARTING: When jumping the battery the vehicle with the good battery should be ran at what RPM ______ to ______
1,000 to 1,500
The steady red light switch activates two red lights located where?
Grille
Adjusting side mirror by hand may cause damage to ___________ mechanism
Adjustment
06’ to 09’ how many liters is the ALF Caterpillar Engine?
12.5
