TB Apparatus C-2,L-7,P-3 Flashcards

0
Q

APPARATUS C-2. 2.3

Who is responsible for ROUTINE MAINTENANCE schedules?

A

Company Commander

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
1
Q

APPARATUS C-2 2.1

Who is responsible for conditions and operations of apparatus under their control?

A

Chauffeurs

Repairs or supplies needed IMMEDIATELY notify OFFICER ON DUTY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

APPARATUS C-2. 2.4

What does the AUTO EJECT PLUG RECEPTACLES supply,while rig is parked in quarters?

A

Battery/Air maintenance system

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

APPARATUS C-2 3.1

What is checked EACH TOUR immediately AFTER roll calls?

A

FLAWS

F FUEL
L LIGHTS
A AIR TANKS (purge)
W warning devices (sirens,air horns, lights)
S SEAT BELTS
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q
APPARATUS C-2 3.1.4
What BULB(s) can we replace?
A

Headlight Bulbs

All other bulbs notify FLEET SERVICES

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

APPARATUS C-2 3.2.4

A reading of ___ volts or higher would indicate that the system is over charging

A

14.8 volts

Battery charge gets checked DAILY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

APPARATUS C-2

With the ENGINE off, a reading of ____ volts or higher indicates the battery has a sufficient charge?

A

12 volts

Battery charge gets checked DAILY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q
APPARATUS C-2
VOLTMETER
engine off?
engine running?
Overcharging?
A

12 volts (sufficient charge)

  1. 5 to 14.2 volts (battery charging)
  2. 8 volts (overcharging)
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

APPARATUS C-2

The max LBS of AIR LOSS in brake system per application?

A

10lbs per application

Brake system gets checked DAILY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

APPARATUS C-2

What is the max LBS of AIR LOSS in brake system per 10 minutes?

A

1lbs per 10 minutes

Brake system checked DAILY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

APPARATUS C-2

How long does the engine have to be shutdown in order to check the oil level?

A

At least
15 minutes

Oil level checked DAILY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

APPARATUS C-2

Oil pressure should be between how many PSI when operating between 1500 to 2100 rpm?

A

30 to 70 psi

Oil pressure checked DAILY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

APPARATUS C-2

When the TREAD of TIRE reaches ___ inch in depth, request a replacement?

A

3/16 inch

Tires/ wheel checks checked DAILY
Tires pressure N wheel lugs WEEKLY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

APPARATUS C-2. 3.2.8

What is an indication that a WHEEL CHECK is loose?

A

When WHEEL CHECK is NOT in sequence
Notify Officer, Officer notifies Fleet Services

Tires checked DAILY

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

APPARATUS C-2. 3.2.10

Where will tools or equipment NOT be stored on the rig?

A

Behind the REARWARD facing seat of crew cab on the CHAUFFEURS SIDE. (Onboard compressor and battery charger are there)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

APPARATUS C-2

What are ADDITIONAL DAILY Maintance performed on ENGINE COMPANY rigs?

A

PEGS

P Primer pump oil
E engage pumps
G gates n valves
S strainers- suction inlets

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

APPARATUS C-2 add 1

Using SNOW CHAINS can approximately ______ your vehicles starting n stopping traction on snow n ice?

A

DOUBLE

When chains are applied apparatus MUST NOT EXCEED 30 mph

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

APPARATUS C-2 add 1
How many snow chains are mounted to a
SINGLE REAR AXLE APPARATUS?

A

2 snow chains
BOTH SIDES
REAR axle OUTER DRIVE WHEELS

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

APPARATUS L-7

How many acting hydraulic LIFT cylinders are on a 100’ft AERIAL LADDER?

A

2 DOUBLE acting hydraulic lift cylinders

Precise elevation from 0-80 degrees above horizontal

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

APPARATUS L-7

What extends OUT n DOWN to provide a firm base for aerial ladders?

A

STABALIZERS

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

APPARATUS L-7

Load capacity depends on what at the tip of an aerial ladder?

A

DEGREE OF ELEVATION

250-750 lbs

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

APPARATUS L-7

How many locations are CONTROLS located on Aerial ladders?

A

3 locations

Aerial control panel (apparatus cab)
Stabilizer controls (rear of apparatus)
Aerial Ladder Controls (apparatus pedestal)

22
Q

APPARATUS L-7 2.2

How does LCC activate PTO?

A
NEUTRAL POSITION
MAXI BRAKE
FRONT BRAKE LOCK SWITCH TO ON POSITION
(front brake light will illuminate)
Open RED COVER of PTO switch, FLIP switch to UP POSITION
(PTO light will illuminate)
23
Q

APPARATUS L-7

How much clearance is required for the stabilizer to be fully extended horizontally?

A

5ft 2inches

This motion is a 1 firefighter operation

24
APPARATUS L-7 | What type of valve is in place to help safeguard the stability of the apparatus?
Interlock Diverter Valve (IDV)
25
APPARATUS L-7 | A properly placed stabilizer will illuminate what color in the Stabilizer Control Compartment?
GREEN When BOTH stabilizers are properly placed BOTH GREEN LIGHTS will illuminate and a signal is sent to IDV.
26
APPARATUS L-7. 3.2.4 | When can we OVERRIDE the Interlock Diverter Valve (IDV)?
Emergency Use ONLY Action should only be performed if there is a MALFUNCTION and an EMERGENCY EXISTS. Notify IC immediately.
27
APPARATUS L-7 | Which STABALIZERS are extended and lowered FIRST?
Inboard STABALIZERS | Working side
28
APPARATUS L-7 | A Stabilizer that is not fully extended horizontally is considered?
Short Jacked
29
APPARATUS L-7 T/F Ground Stabilizer Pads MUST be used ALL THE TIME?
True
30
APPARATUS L-7 | What stabilizer would be lowered first, when ground is NOT LEVEL and apparatus is LEANING?
Lowest side First
31
APPARATUS L-7. 5.1 | What system is used when the normal PTO FAILS or the ENGINE SHUTS DOWN and the AERIAL LADDER or JACKS need to be USED?
Emergency HYDRAULIC SYSTEM Consists if an electrical auxiliary hydraulic pump and 4 Emergency switches
32
APPARATUS L-7. 5.2 | What color in the AERIAL CONTROL PANEL will the NORMAL/EMERGENCY HYDRAULIC SWITCH to the AUXILIARY POSITION illuminate?
RED
33
APPARATUS P-3 1.5 | Pumpers are to be maintained in what POSITION unless HEAD PRESSURE must be overcome?
Volume Position
34
APPARATUS P-3 | What VALVE is used to change positions from VOLUME TO PRESSURE?
Transfer Valve
35
APPARATUS P-3 | What POSITION is used for STANDPIPE operations?
Pressure Position
36
APPARATUS P-3 | What is PUMP IDLE PRESSURE?
The PRESSURE the pumps provide at its LOWEST RPM's In VOLUME around 55psi In PRESSURE around 110psi PLUS HYDRANT PRESSURE
37
APPARATUS P-3 | What MODE is used in an EMERGENCY SITUATION as a BACK-up in the event the PRESSURE MODE MALFUCTIONS?
RPM MODE
38
APPARATUS P-3 | What is the PRESSURE known as on the GUAGE when water IS NOT FLOWING?
STATIC PRESSURE
39
APPARATUS P-3 | How do we test a HYDRANT?
REMOVE large cap TIGHTEN small cap Do not open HYDRANT FULLY
40
APPARATUS P-3 | What HYDRANT CONNECTION(s) can be used when OTHER than FIRST to ARRIVE on the FIRST ALARM?
10'ft small 10'ft hard 35'ft soft
41
APPARATUS P-3 E80 E69 E37 L23 L28 respond to a box on 137 n Amsterdam Ave, what HYDRANT CONNECTIONS would E80 be able to use and what HYDRANT CONNECTIONS would E69 n E37 use?
Arrived FIRST DUE E80 10'ft small 35' soft Arrived 2nd E69 n 3rd due E37 10'ft small 10'ft hard 35'ft soft
42
Apparatus P-3 When MUST you use the 10ft HARD suction? When SHOULD you use the 10ft HARD suction?
MUST at DRAFTING SHOULD when ARRIVING at SECOND or GREATER ALARMS
43
APPARATUS P-3. 4E | How many LENGTH(s) of hose may be used, when hydrants are blocked at fires and the 35ft cannot reach?
A LENGTH
44
APPARATUS P-3 What is the proper way in hooking up to a hydrant? Hydrant first or Apparatus first
Hydrant FIRST then APPARATUS in case of repositioning
45
APPARATUS P-3 | When _______ pressure drops BELOW ___psi on the INTAKE PRESSURE GUAGE, augmentation is required?
Residual | 15 psi
46
APPARATUS P-3 8.1 | When do you PRIME the pumps?
AFTER WATER is introduced | BEFORE increasing pump pressure and opening discharge outlets
47
APPARATUS P-3 | What are the 6 functions of the Pro Pressure Governor (PPG)
``` Idle Increase Decrease Rpm Pressure Preset ```
48
APPARATUS P-3 9.2 6 | What should the PRESET button on the PPG be based on?
Typical HYDRANT PRESSURE with the PRESSURE the pumps IDLE at in VOLUME Hydrant pressure + typical volume psi Provides PUMP IDLE PRESSURE
49
APPARATUS P-3 | What is LINE PRESSURE determined by?
``` SIZE of hose + NUMBER of lengths of hose + Nozzle pressure and Elevation ```
50
APPARATUS P-3 | How much FRICTION LOSS per length of hose for an 1 3/4 hose w/ a 1 5/16 nozzle?
50psi @ nozzle+ 20psi per length
51
APPARATUS P-3 10.3.4 | How MUST HYDRANT water be brought INTO the pumps when operating from BOOSTER WATER?
Through a GATED INLET
52
APPARATUS P-3 | When do u notify your officer of what kind of water your on?
Both When operating on BOOSTER WATER and then again once the rig is on HYDRANT WATER