Engine Start Knowledge Flashcards

1
Q

When will the CP call for the FO to start the engine?

A

After completion of the Engine Start Check Flow and the Engine Start Checklist

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Where is the procedure for starting the engines located?

A

SOPM 04-03.7

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Which engine is started first for FFOD?

A

1 for the Fuel Feed Check Valve

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Which engine is started first for Non-FFOD?

A

2

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Which engine is used for single engine taxi?

A

2

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

When only starting a single engine for taxi, when is the other engine started?

A

Digression of CP

-During Taxi

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

The APU must be started how many minutes prior to pushback?

A

10 minutes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What is the procedure for starting the APU on the ground?

A

Review

SOPM 04-16.6

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What must be set for the Takeoff Data Task item?

A

-V-Speeds
-Speed Bug V2+20
-N1 thrust setting
(All stated by FO)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What is set/checked of the Trim task?

A
  • Stab T/O Setting (Stated by FO)

- Aileron + Rudder centered

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What could occur if stab trim setting is inappropriately set?

A

Excessive rotation

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Transponder task requires the transponder is set to which side?

A

PF Side

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Prior to closing the MCD, what must be checked?

A

Low Pressure external air has been disconnected

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What items must the CP check before having the FO start an engine?

A
  • Fuel Pumps ON

- Ignition ARMED

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What are the FO actions and callouts for starting an engine?

A

Review

SOPM 04-03.7

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

When starting and engine, what two messages that the FO must check on ED-2?

A
  • L or R ENGINE START (White)

- Ignition A or B (Green)

17
Q

What does the FO check for on the ITT and N2 gauges prior to moving thrust lever to idle?

A

ITT: < 120 C
N2: > 20%

18
Q

When is the FFOD Fuel Feed Check Valve Test Part 1 conducted?

A

After starting Engine 1

19
Q

After two minutes has elapsed and no R FUEL LO PRESS caution message is displayed what will the FO do?

A

Dry Motor the engine

20
Q

How long can the engine be dry motored for the FFOD Fuel Feed Check Valve Test?

A

30 seconds

21
Q

What does the absence of the R FUEL LO PRESS indicate?

A

Fuel Feed Check Valve has FAILED in the OPEN position

22
Q

What action should the crew take in the absence of the R FUEL LO PRESS caution message?

23
Q

Can both engines be started at the gate with the jetway connected and the MCD open?

24
Q

Who must be notified when engines will be started with the MCD open?

25
Before the FFOD, prior to starting a cold soaked engine, what is required?
Engines must be motored for 60 seconds an fan rotation verified before start
26
Prior to departure in a cold soaked airplane, the thrust reverser deploy and stow cycles must be less than how many seconds?
< 5 seconds
27
Where is the CRJ200 cross bleed engine start located?
Review | QRH Volume 1: Engine Start - Cross Bleed
28
Where is the external air engine start procedure located?
Review | QRH Volume 1: Engine Start - External Air
29
What is required prior to aircraft movement?
- Obtain clearance | - Establish + Maintain audio or visual contact with pushback crew
30
What is the release brakes hand signal to ground personnel?
Start with clenched fist, then extend fingers, palm toward you
31
How do procedures vary with using the LEKTRO cart?
- Brakes released and AC positioned into cart prior to pushback - Cart operator request brakes on after push before removing AC from cart bucket
32
What pushback procedures are to be followed during pushback on a contaminated ramp?
-Engine start delayed until pushback complete -If engine start is required prior to pushback > Only one engine started > Engine must remain at idle during push > Pushed to ADQ traction before XBleed start > PIC Not permit push without headsets
33
What are the HOT START memory items?
> Affected Thrust Lever - SHUTOFF > Ignition - OFF > Dry Motor - UNTIL ITT <120 within starter limits
34
What are the INTERRUPTED START memory items?
> Affected Thrust Lever - SHUTOFF > Ignition - OFF > Dry Motor - UNTIL ITT <120 within starter limits
35
What are the N2 STAGNATION memory items?
> Affected Thrust Lever - SHUTOFF > Ignition - OFF > Dry Motor - UNTIL ITT <120 within starter limits
36
What are the NO LIGHT OFF memory items?
> Affected Thrust Lever - SHUTOFF > Ignition - OFF > Dry Motor - UNTIL starter time limit
37
What procedure should be followed for a NO STRTR CUTOUT caution message?
Affected ENG STOP: Stop