Indicating, Landing Gear, Lights, Nav

Question 1

If the GND CTL is not ON, when will the
recorders run?

Answer 1

1. Five (5) minutes when
   electrical power is applied.
2. After engine start
3. Five (5) minutes after second
   engine shutdown.
4. Runs continuously inflight

Question 2

Which display units would be lost if DMC 1 fails
on LCD equipped aircraft?

Answer 2

On LCD equipped aircraft the
CA PFD and ND will be lost.
(Unless crew manually select DMC 3 on Switching Panel)
E/WD and SD will be lost
temporarily but automatically
restored by DMC 2

Question 3

What brake system(s) pressure can be displayed
on the indicator below?

Answer 3

Top
Yellow System Accumulator
Pressure
Bottom
Yellow system pressure applied
to the brakes.

Question 4

What do the red UNLK lights on the Landing
Gear panel represent?

Answer 4

Landing Gear
NOT
Locked in the selected position

Question 5

What is the effect on braking if Green hydraulic
system pressure is lost?

Answer 5

Yellow system takes over.
Anti-Skid still available
NW Steering and Autobrakes
LOST

Question 6

Assuming a loss of Green and Yellow system
pressure, what hydraulic source is supplying
braking?

Answer 6

Yellow
System
Accumulator

Question 7

When does the AUTO function of the STROBE
Light switch turn the strobes on?

Answer 7

Weight
OFF
Wheels

Question 8

The radar is selected ON in WX/TURB mode.
Within how many miles ahead of your aircraft can
turbulence be shown in precipitation?
▪ What color is used to display turbulence?

Answer 8

40 NM (Regardless of Range)
Turbulence shown in MAGENTA

Question 9

If the Radar system was selected OFF and
WINDSHEAR was selected to AUTO. Windshear
is predicted ahead of your flight path. Will you
receive a Predictive Windshear alert?

Answer 9

YES
Predictive WSHR warning is
provided despite radar selection

Question 10

Describe the required steps to tune and track a
VOR radial after selecting STBY NAV

Answer 10

1. Select VOR pb
2. Use selector knob to tune
   frequency and course
3. Select “ROSE VOR” on ND to
   fly radial.

Question 11

If the TERR pushbutton shows a FAULT, what has been lost?

Answer 11

Database Terrain Detection Fail

(Basic GPWS modes still available)

Question 12

Which portion of the
system (ADR or IR)
provides Attitude and
Heading
information?

Answer 12

Inertial Reference

Question 13

Which portion of the
system (ADR or IR)
provides Barometric
Altitude and Angle of
Attack information?

Answer 13

Air Data Reference

Question 14

What does the flashing white ALIGN lights represent?

(Hint: M-I-N-D)

Answer 14

1. Movement of Aircraft
2. IR alignment fault
3. No PPOS entry after 10 minutes
4. Difference of >1o LAT or LONG between position at
   shutdown and entered position

Question 15

What does a flashing amber FAULT light
indicate above the IR3 rotary switch?

Answer 15

Fault in IR 3

(Attitude and heading may be recovered in ATT Mode)

Question 16

401
What effect does each turn of the GEAR EXTN handle have?

Answer 16

Pull the gear crank out, and turn clockwise for three turns. This releases hydraulic pressure to the gear, opens the gear doors and unlocks the gear

Question 17

Assuming a loss of Green and Yellow system pressure, what source is available for braking?

Answer 17

Yellow–BRK ACCU PR ONLY

Question 18

By selecting the A/SKID& N/W STRG switch OFF
(per Loss of Braking Memory items),
what effect does this have on the braking system?

Answer 18

Green Hydraulic pressure is shut off to the Normal Brake System. Yellow hydraulic system supplies pressure to the brakes without anti-skid protection.

Question 19

409
If the DECEL light fails to illuminate after landing,
what does this indicate?

Answer 19

The predetermined deceleration rate has NOT been achieved