Flows / Procedures (airline specific) Flashcards
When the captain calls for ‘Before start checklist to the line’, what does the FO do before actioning the checklist?
Sets the fuel panel for departure. (Centre fuel pumps on if tanks contain greater than 453kgs).
On confirmation of steering bypass pin installed, or ground crew checks complete, what are the FO’s actions?
- Hydraulic panel Set
- Start and/or Push Request
- Pack switches Off
- Anti Collision light On
- Transponder On (no TCAS)
What is the correct flow when the captain calls “Before Taxi Procedure”?
- GEN 1 and 2 ON
- PROBE HEAT ON
- PACKS AUTO
- ISOLATION VALVE AUTO
- APU BLEED OFF
- ENGINE START SWITCHES CONT
- WING ANTI-ICE As req.
- ENGINE ANTI-ICE As req.
(Verify ground equipment clear, silently verify flap selection in FMC).
E P P S A
What happens after the captain checks the flight controls?
FO blanks lower DU
Recall is checked.
What happens after receiving taxi clearance immediately before starting to taxi?
Both pilots verify area is clear and call “ Clear left/right”
- FO sets APU as needed
- FO turns on Taxi/Turnoff lights
Describe the steps for the Before Take-Off Procedure
PM: Verify that the cabin is secure
Pilot doing take-off updates any changes to take-off brief.
Both pilots:
- select WX or Traffic as needed
- verify runway and entry point correct.
When entering departure runway; PM:
- Check centre tank fuel quantity. If less than 1000kgs, centre pumps OFF (disregard CONFIG).
- Cycle NO SMOKING / CHIME switch to notify CC of imminent T/O
- STROBE lights ON
- External lights as needed
- Transponder to TA/RA
PF: “BEFORE TAKE-OFF CHECKLIST”
C R R A S S I T
Which lights does the FO turn on when cleared for take-off?
FIXED LANDING / LANDING lights
What is the PM’s flow after calling “FLAPS UP, NO LIGHTS”?
- Set or verify engine bleeds and air conditioning packs are operating
- Set the engine start switches as needed
- Set the AUTO BRAKE to OFF
- Set the landing gear lever to OFF after gear retraction complete
When does the Climb Procedure normally commence and what does it entail?
Commences following completion of after T/O checklist.
PF: Monitor acceleration.
PM: Monitor RNP
PF: Call “Release cabin crew”
PM: Cycle NO SMOKING or CHIME only
What happens when climbing through FL100?
PM verifies cabin pressurisation and turns off Landing lights, turnoff lights and Logo light.
PF takes consideration of conditions and calls “Fasten Belts Signs Auto”.
PM selects Fasten Belts switch to AUTO
When passing 10,000’ AAL in the descent, which lights does the PM turn on?
RUNWAY TURNOFF and LOGO
What is the after landing procedure?
(Chrono started when engines idle after landing)
Captain: Speedbrake lever down
FO:
- start APU as needed
- PROBE HEAT AUTO
- Set exterior lights as needed
- ENGINE START switches OFF
- Deselect WXR on EFIS control panel
- WX radar TEST or OFF
- AUTOBRAKE OFF
- FLAPS UP
- TCAS DESELECT
- STAB TRIM GREEN BAND
W A P I S R A F T S
What are the steps taken to shut down an engine for the single engine taxi procedure?
FO: “3 minutes 30 seconds”
Verify APU started, available and on bus.
Captain: Instruct FO to shutdown engine no.1
FO: “CONFIRM START LEVER NUMBER 1”
Captain: “CONFIRMED”
FO: Shutdown engine no.1, verify spar and engine fuel valves illuminate bright then dim.
What is the FO’s flow during the shutdown procedure?
Electrical power: GPU or APU
FASTEN BELTS OFF
ANTI COLLISION (N1 <10%) OFF
FUEL PUMPS As needed
(can stay on during turnaround)
CAB/UTIL power As needed
IFE/PASS SEAT ON
WING-ANTI ICE OFF
ENGINE ANTI-ICE OFF
Hydraulic Panel As needed
(can stay on during turnaround)
RECIRC FANs As needed
PACKS As needed
(if air con needed; AUTO, if not; OFF)
ISOLATION VALVE OPEN
Engine BLEEDS ON
APU BLEED As needed
Exterior lights As needed
FLIGHT DIRECTORS OFF
MCP IAS 100
Transponder 2000, del FLT number
What is the FO’s secure procedure?
IRSs OFF
EMERGENCY EXIT LIGHTS OFF
WINDOW HEAT OFF
Elec Hyd Pumps OFF
PACKS OFF
Cockpit video OFF
