Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

Hatch ILT-14 Study Guide > EOP Facts > Flashcards

EOP Facts Flashcards

1
Q

During RPV floodup, what is the elevation of top of active fuel?

A

83.9 feet (35 psid)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

During RPV floodup, what is the maximum primary containment water level?

A

103.5 ft (43.5 psid)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What indications are available in the control for primary containment flooding?

A

On Control Room panels 2H11-P657 and P654, 2T48-R622A and B, Wide Range Torus Wtr Lvl, will indicate torus water levels below 25 feet (300 inches).

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Actions to transfer HPCI from injection to pressure control?

A

Reset the HPCI initiation signal
IF the HPCI initiation cannot be reset,
THEN do NOT perform this section (EOP-107)

With the HPCI Flow Controller in Auto, closing 2E41-F008 will increase the cooldown rate.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Actions to transfer RCIC from injection to pressure control?

A

IF RCIC MANUAL INITIATION PUSH BUTTON IS DEPRESSED, INJECTION TO VESSEL WILL INITIATE. IF INJECTION IS INITIATED, IT CAN BE STOPPED BY DEPRESSING THE RCIC INITIATION SIGNAL RESET PUSH BUTTON AND THEN CLOSING 2E51-F013, PUMP DISCHARGE VLV.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Maximum dp for MSIVs?

A

The MSIVs are designed to open against a dP of up to 200 PSID.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Steps for RWCU blowdown for alternate pressure control?

A

THIS SECTION IS NOT TO BE PERFORMED IF BORON HAS BEEN, OR
IS BEING INJECTED TO THE RPV.
OPEN
2G31-F034, Disch To Main Cndsr Vlv, _____
OR
2G31-F035, Drain to Waste Coll Vlv, At panel 2H11-P602. _____
DO NOT OPEN BOTH OF THESE VALVES AT THE SAME TIME.

Maintain the Non-Regenerative Heat Exchanger effluent temperature at <120°F,

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Maximum SJAE steam supply pressure?

A

do not exceed 360 psig

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

HPCI for alternate RPV depressurization

A

Adjust 2E41-R612, HPCI Flow Control,
to obtain 4250 GPM AND
throttle 2E41-F008 CLOSED
UNTIL the Turbine Control Valve is Full OPEN,
DO NOT exceed 1500 psig discharge pressure.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

RCIC for alternate RPV depressurization

A

3.4.15 Adjust 2E51-R612, Turbine Controller,
to obtain 400 GPM AND ______

3.4.15.1 Throttle, 2E51-F022, CLOSED
UNTIL Turbine Governor Valve is FULL OPEN,
DO NOT exceed 1500 psig discharge pressure.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

RFPT for alternate RPV depressurization

A
  • This subsection provides an alternate method of RPV Depressurization by operating the Reactor Feed Pump Turbines. This subsection is to be performed ONLY WHEN the Condensate/Feedwater System is NOT required for RPV water level control AND the Main Condenser can be placed in operation with at least 7.0 in Hg. vacuum.
  • The RFPTs will trip on low vacuum of 22.3 in Hg vacuum if speed goes above 3500 RPM
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What to do for alternate depress when vacuum is less than 10 in. Hg?

A

IF vacuum of at least 10 in. Hg vacuum CANNOT be drawn on Main Condenser,
(Monitor → LP Hoods , 2N32-K4001A OR 2N32-K4001B) OR SPDS,
THEN confirm OPEN/OPEN Main Condenser Vacuum Breaker Valves

AND

START all available Turbine Building HVAC per 34SO-U41-001-2, Turbine Building Ventilation System.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Alternate depress with RWCU

A

THROTTLE 2G31-F044, Demin Bypass Vlv,

to establish a system flow rate of 250-260 GPM.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

During alternate boron injection, what is runout condition with CRD?

A

THE CRD PUMPS WILL EXPERIENCE A RUNOUT CONDITION AT ≈190 GPM.
THIS CORRESPONDS TO A DISCHARGE PRESSURE OF ≈ 1180 PSIG.
THE NET POSITIVE SUCTION HEAD REQUIRED FOR THIS FLOW CONDITION IS 18.0 INCHES HG VACUUM.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

HPCI Injection flow prior to disabling min flow?

A

HPCI system must be injecting to vessel with more than 960 gpm (set point for min flow valve operation) flow rate to allow proper cooling of HPCI pump prior to disabling the Min Flow Valve.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

At what level and what component would disable on SBLC during alternate boron injection?

A

WHEN SBLC Storage Tank level decreases below 20%,
THEN open the following breakers:
SBLC Tank Htr B 2C41-A001 breaker R24-S011 Frame 1B.
SBLC Tank Htr A 2C41-A001 breaker 2R24-S012 Frame 3A.

17
Q

RCIC injection flow prior to disabling min flow?

A

RCIC system must be injecting to vessel with more than 122.5 gpm (set point for min flow valve operation) flow rate to allow proper cooling of RCIC pump prior to disabling the Min Flow Valve.

18
Q

What temperature will promote proper chemical mixing on SBLC?

A

For a full batch 1975 pounds of enriched sodium pentaborate is required.
Maintaining SBLC Storage Tank temperature > 100°F will promote proper chemical mixing.
WHEN SBLC Storage Tank Temperature reaches 110°F,
as read on 2C41-R002, SBLC Storage Tank Temp Indicator,
THEN commence adding enriched Sodium pentaborate to Storage Tank
as directed by Chemistry personnel

19
Q

Steps to shutdown or prevent injection with HPCI?

A

‌1.IF HPCI is NOT operating,
THEN perform ONE of the following:
‍a.IF HPCI operation is NOT desired,
THEN, PLACE 2E41-C002-3, HPCI Aux. Oil Pump, in PULL-TO-LOCK. ______
‍b.IF HPCI operation IS desired and injection is not desired at this time,
THEN, PLACE 2E41-R612, HPCI Flow Controller in MANUAL with an output signal of ~50% or as required to maintain HPCI discharge pressure below RPV pressure,
WHILE maintaining Turbine speed > 2000 RPM when operating. ______
‌2.IF HPCI is operating,
THEN perform ONE of the following:
‍a.IF continued HPCI operation is NOT desired,
THEN perform the following:
‍(1)DEPRESS and HOLD HPCI Remote Turbine Trip push-button. ______
‍(2)WHEN HPCI Turbine has stopped,
PLACE 2E41-C002-3, Aux. Oil Pump, in PULL-TO-LOCK. ______
‍(3)WHEN HPCI TURBINE BRG OIL PRESS LOW alarm is received,
RELEASE HPCI Remote Turbine Trip push-button. ______
IF continued HPCI operation is desired,
THEN REDUCE 2E41-R612, flow controller in manual or auto,
to prevent injection WHILE maintaining Turbine speed > 2000 RPM.

20
Q

Terminating and prevent injection for condensate for emergency depress

A 
‌1.IF Terminating and Preventing Injection is being performed for EMER DEPRESS, 
THEN Perform the following:
TRIP BOTH RFPTs:
2N21-C005A	\_\_\_\_\_
2N21-C005B	\_\_\_\_\_
TRIP Condensate Booster Pumps AND place Control Switches to 
PULL NON AUTO, 2H11-P650:
2N21-C002A	\_\_\_\_\_
2N21-C002B	\_\_\_\_\_
2N21-C002C	\_\_\_\_\_
TRIP ALL EXCEPT ONE Condensate Pump, 2H11-P650:
2N21-C001A	\_\_\_\_\_
2N21-C001B	\_\_\_\_\_
2N21-C001C	\_\_\_\_\_
CLOSE the following valves, 2H11-P650:
2N21-F110, S/U LEVEL CONTROL BYPASS	\_\_\_\_\_
2N21-F125, S/U LEVEL CONTROL ISOL
21
Q

Terminating and prevent injection for condensate for lower water level

A

‌2.IF Terminating and Preventing Injection is being performed to Lower Rx Water Level for Rx Power control,
THEN Perform the following:
Manually control the RFPT(s) to maintain discharge pressure below reactor pressure. ______
CLOSE the following valves, 2H11-P650:
2N21-F110, S/U LEVEL CONTROL BYPASS ______
2N21-F125, S/U LEVEL CONTROL ISOL

22
Q

Core Spray terminating and preventing injection

A

NOTE: If Terminating And Preventing Injection for level / power control and Rx Pressure is above the CORE SPRAY shutoff head of 280 psig then this subsection does not have to be completed for Terminating And Preventing to be considered complete.

‌1.IF IMMEDIATE Terminating and Preventing Injection is being performed for EMER DEPRESS OR Lowering RPV Pressure, 
THEN Perform the following:
CLOSE the following valves, 2H11-P601:
2E21-F005A INBD DISCHARGE VLV	\_\_\_\_\_\_
2E21-F005B INBD DISCHARGE VLV	\_\_\_\_\_\_
TRIP the following pumps:
2E21-C001A Core Spray Pump A.	\_\_\_\_\_\_
2E21-C001B Core Spray Pump B.

At this point, TERMINATION AND PREVENTION of CORE SPRAY injection may be considered complete however; continuous operator monitoring of CORE SPRAY will be required UNTIL the following step is performed.

23
Q

LPCI terminating and preventing injection

A

If Terminating And Preventing Injection for level / power control and Rx Pressure is above the RHR shutoff head of 220 psig then this subsection does not have to be completed for Terminating And Preventing to be considered complete.
If Immediate Terminating and Preventing Injection is being performed for EMER DEPRESS OR Lowering RPV Pressure and 31EO-EOP-114-2 step 3.2 has been completed OR Section4.4Step2 thru Section4.4Step5 of this procedure are complete, THEN Section4.4Step1 does not have to be completed for Terminating And Preventing to be considered complete.

‌1.IF IMMEDIATE Terminating and Preventing Injection is being performed for EMER DEPRESS OR Lowering RPV Pressure,
THEN Perform the following:
CLOSE the following valves, 2H11-P601:
2E11-F016A(2E11-F016B), CNMT SPRAY OUTBD VLV ______
2E11-F0228A(2E11-F028B), TORUS SPRAY OR TEST VLV ______
TRIP the following pumps:
2E11-C002A RHR Pump A. ______
2E11-C002B RHR Pump B. ______
2E11-C002C RHR Pump C. ______
2E11-C002D RHR Pump D.

24
Q

Override interlocks 2E11F017A/ 17B

A 
‌3.To Override the interlocks for 2E11-F017A/2E11-F017B, RHR Outbd Inj Vlvs, 
PERFORM the following actions.
‍(1)LPCI A loop, 2H11P617B:
OPEN LINK   FF-38	\_\_\_\_\_\_
INSTALL JUMPER  FF-39  to  FF-40	\_\_\_\_\_\_
‍(2)LPCI B loop, 2H11P617B:
OPEN LINK FF-36	\_\_\_\_\_\_
INSTALL JUMPER  FF-37  to  FF-38
25
Q

RCIC terminating and preventing injection

A

‌1.IF RCIC operation is no longer desired,
THEN perform the following:
‍(1)DEPRESS the RCIC turbine trip push-button. ______
‍(2)IF desired,
CLOSE 2E51-F524, Trip and Throttle Vlv.,
using the control switch on 2H11-P602. ______
‌2.IF continued RCIC operation is desired,
THEN:
REDUCE flow controller, 2E51-R612,
to prevent injection
WHILE maintaining turbine speed > 2000 RPM.

26
Q

Core Spray pump prevented from injection, what happens on loca signal?

A

ANY SUBSEQUENT LOCA SIGNAL WILL CAUSE THE CORE SPRAY PUMPS TO AUTO START AND WILL ALSO ALLOW THE DISCHARGE VALVE TO AUTO OPEN.

Hatch ILT-14 Study Guide (14 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions