Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

4806 > Steam Generating/SGWLC/Blowdown > Flashcards

Steam Generating/SGWLC/Blowdown Flashcards

1
Q

What do the J tubes help to prevent?

A

Water Hammer when AFW initiates

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What does the flow restrictor do on each MS outlet from the SG?

A
  • Provide plant protection, in case of MSLB, by decreasing steam flow rate to reduce RCS cooling rate.
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is P-14 permissive?

A

SG Hi HI Lvl at 67% on 1 SG (2/3) FWI

SG level at 64% allows feeding

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What will P-14 permissive cause?

A
  • Turbine Trip
  • MFP Trip
  • FWI
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What enables AMSAC?

A

Greater than 40% Power (C-20, 2/2 Turbine first stage Impulse pressure)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What generates an AMSAC signal?

A

FW flow < 25% (3/4 Feed flow)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What will AMSAC actuate?

A
  • Trips Main Turbine (30 Sec)
  • Starts All 3 AFW Pumps
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

When do DCR-310-340 (BD isolation valves) automatically isolate?

A
  • Phase A
  • High Rad:DRA300 and DRA-353
  • High Level in Flash Tank
  • AFW Flow Conservation / Pump Starts
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Where do we drain both flash tanks to?

A
  • TRS Overflow via DRV-350
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

When do BD sample isolation valves (DCR-301-304) automatically close?

A
  • High Rad
  • Phase A
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Control air header pressure is lowering at a fast rate. At 80 psi, the reactor is manually tripped, and header pressure continues to lower. What will happen to the air reg valves in the BD system if pressure continues to lower?

A

All air reg valves on BD system will isolate on loss of ctrl air

  • DRV-350/352
  • BD isolation valves
  • BD Flow Ctrl Valves
  • BD Sample Valves
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is the cooling water to the BD Hx and flash tank quenching?

A

Containment Chill Water

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What supplies cooling to the BD sample Hx?

A

CCW

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What plant protection functions do the SG pressure transmitters provide?

A
  • SG Steam Line Break Detection
  • SI Initiation
  • Main Steam Line Isolation
  • Low Steam pressure Alarms
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What causes a Steam Line Isolation (SLI)?

A
  • Cnt # High-High at 2.8# (2/4)
  • SG # low < 500# (1/1 on 2/4 SG)
  • High Stm flow with P-12 (1.42E6/1.6E6) (1/2) on 2 SG
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What is density compensation?

A

Converts volumetric flowrate of steam to mass flowrate for input into SGWLC circuit
(Left 2 Channels)

17
Q

Where do we measure SG Level?

A

SG Downcomer

18
Q

What is swell caused by?

A

An increase in steam flow
(which will cause an increased indication of SG lvl in the downcomer due to decreased SG pressure)

19
Q

What is shrink caused by?

A

A Reduction in steam flow
(which will cause an decreased indication of SG lvl in the downcomer due to a rise in SG pressure)

20
Q

In MODES 1 and 2, the reactor is critical and thus has the potential to produce maximum THERMAL POWER. Thus, to ensure that the assumptions of the accident analyses remain valid, all RCS loops are required to be OPERABLE and in operation in these MODES to prevent (what 2 things)

A

DNB and Core Damage

21
Q

If the controlling channel STEAM flow fails high, what will happen the FRV?

A

The FRV will go open because Feed Flow will want to match Steam Flow

22
Q

If the controlling channel STEAM flow fails low, what will happen the FRV?

A

The FRV will go closed because Feed Flow will want to match Steam Flow

23
Q

If the controlling channel FEED flow indication fails low, what will happen the FRV?

A

The FRV will go open because Feed Flow will want to match Steam Flow

24
Q

If the controlling channel FEED flow indication fails high, what will happen the FRV?

A

The FRV will go closed because Feed Flow will want to match Steam Flow

25
Q

What will happen if either the SG Level or Flow Controllers are lost?

A

The RU will instantly go to manual to maintain the FRV at its current position

26
Q

Unit 1 was operating at 100% power when a loss of main feedwater occurs to a single SG due to the failure of the controlling feedwater flow instrument.

A valid indication on the affected SG “Flows / Level / Pressure” recorder for this failure would be a rapidly lowering SG level and a?

A

high feedwater flow indication on the feedwater flow pen

27
Q

What will cause a FWI?

A
  • SG High-High level (P-14) (67% NR 2/3 on 1 SG)
  • SI
  • Rx trip (P-4) with low Tavg (Tavg less than 554°F on 2/4 loops)
28
Q

What happens on a High High SG Level of 67%?

A
  1. FWI
  2. Turbine Trip
  3. MFP Trip
29
Q

Can chemistry override the High Radiation signal that made the sample valves closed?

A

YES

30
Q

High Level in a Blowdown Flash Tank will…

A

Close Blowdown Isolation DCRs 310 through 340

31
Q

Low Level in a Blowdown Flash Tank will…

A
  • Trip SGBD Treament Pump
  • Close DRV-350 SGBD Flashtank to TRS
32
Q

Why does a failure of the SG Pressure input affect that SGs SF channel?

A

Because the steam flow channels are density compensated

4806 (10 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions