Oxyacetylene Flashcards

1
Q

What goggles should be worn when using oxyacetylene?

A

Either a #4 or #5 in a green shade

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What should you do if an oxygen cylinder leaks?

A

Remove it from service, take outside away from sources of ignition, tag it as to the type of fault, and notify the supplier.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What do you do when a cylinder requires filling?

A

Should marked MT with chalk or soapstone.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What should you do to a cylinder before it is stored or transported?

A

A removable cap should be installed to protect the valve

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

The valve on a oxygen cylinder has what kind of thread turn?

A

Right hand thread

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Goggles are worn when using Oxyacetylene equipment to protect the eyes from?

A

Light, heat, Sparks and slag.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Technician a says it is acceptable to carry a disposable lighter in your pocket when using Oxyacetylene equipment. Technician B says nylon clothing is much better to wear then cotton when using Oxyacetylene equipment which technician is right?

A

Neither technician

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

To check for leaks and Oxyacetylene equipment you should use?

A

Soap and water

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Shop ventilation is adequate when cutting which of the following with Oxyacetylene equipment?
A.) galvanized sheet metal
B.) The cadmium coated muffler
C.) A piece of metal joint with lead tin-alloy solder
D.) none of the above

A

D.) none of the above

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q
If grease is exposed to pure oxygen, the grease can explode: 
A.) without ignition
B.) only if a spark ignited it 
C.) only if a flame ignited it 
D.) any of the above
A

A.) without ignition

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q
When oxygen from a cylinder is being used, the valve should be opened?
A.) fully 
B.) no more than 2 turns 
C.) no more than 1 turn 
D.) no more than 1/2 turn
A

A.) fully

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q
Fusible plug in acetylene cylinders are located: 
A.) in the top of the cylinder 
B.) in the bottom of the cylinder 
C.) both a) and b) 
D.) neither a) or b)
A

C.) both a) and b)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Acetylene should be drawn from an acetylene cylinder only when the cylinder is:
A.) located with the words up only pointing up
B.) upright
C.) on its side
D.) upside down

A

B.) upright

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

As the cylinder pressure decreases, what does the the outlet pressure from a pressure regulator do?

A

It remains constant

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What colour is the oxygen hose that is used with Oxyacetylene equipment?

A

Green

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What colour is the acetylene hose used with Oxyacetylene?

A

Red

17
Q

All fittings used for oxygen used in Oxyacetylene equipment:
A.) are identified with an annular groove
B.) are left hand threaded
C.) both a) and b)
D.) neither a) or b)

A

D.) neither a) or b)

18
Q

Flashback arrestors used with Oxyacetylene equipment are installed in?

A

Both the oxygen line and the acetylene line

19
Q

What do you do when you are finished using the Oxyacetylene equipment?

A

The oxygen and acetylene should be shut off at the cylinders, and the regulators should be backed out completely.

20
Q

What is the most suitable flame to use when heating with Oxyacetylene equipment?

A

A neutral flame

21
Q

When do you start cutting an Oxyacetylene torch is:
A.) always held at 90° to the material
B.) inclined more for thin material
C.) inclined more for thick material
D.) held at a 45° angle to start the cut and straight to 90° as the cut progresses

A

B.) inclined more for thin material

22
Q

A backfire that occurs when using an Oxyacetylene heating tip might occur because?

A

Acetylene pressure is too low

23
Q

What material can be cut easily using an Oxyacetylene torch cutting attachment?

A

Carbon steel

24
Q

When using Oxyacetylene equipment for heating, the acetylene regulator is adjusted to?
A.) The pressure used when balancing the torch
B.) The pressure recommended by the manufacturer
C.) 7kPa (1psi) per tip size
D.) 105 kPa (15psi) per tip size

A

A.) The pressure used when balancing the torch