Flows Flashcards
FO Transit Scan -
List the initial 5 Items
The checklist finishes with
- Glare shield set up for departure
- Pull GRND OP TEST SW MWS(Master Warning System)
- Check trim operation on control column
- FDR
- Oxygen
- Radio Aids Set Up
- Take off data
- Instrument panel set up
- RNAV
- Fuel
- Circuit Breakers
- Lights
- Aircon settings and RAM Airshut
- Cabin fan on
- Pressurisation controller set
What is the FO Transit Scan?
- Circuit Breakers
- Lights
- Aircon settings and RAM Airshut
- Cabin fan on
- Pressurisation controller set
- Glare shield set up for departure
- Pull GRND OP TEST SW MWS(Master Warning System)
- Check trim operation on control column
- FDR
- Oxygen
- Radio Aids Set Up
- Aileron, Elevator Trim
- Take off data
- Instrument panel set up
- RNAV
- Fuel
Starting with selecting flap to the required setting for take-off what are the other 4 items for the FO taxi scan?
Radar Standby
Flight director on GA if PF
IVSI - Mode full time
Flight controls check elevator/aileron
FO Transit Scan -
List the missing Items
The checklist starts with
- Circuit Breakers
- Lights
- Aircon settings and RAM Airshut
- Cabin fan on
- Pressurisation controller set
- Glare shield set up for departure
- Pull GRND OP TEST SW MWS(Master Warning System)
- Check trim operation on control column
- FDR
- Oxygen test / pressure
- Radio / radio Aids Set Up
- Aileron and Elevator Trim
- Take off data
- Instrument panel set up
- RNAV
- Fuel
What are the two parts of the - Load sheet arrival / starting flow?
- Radios
- Pushtest MWS
- Pull GRND OP SW, Push in
- Data Card, Record info
Starting
- Beacon on
- TCAS on
- Air Supply off
What are the - During Taxi FO scans?
- Flap to required setting for T/O
- Radar to Standby
- Flight Director on GA if PF
- IVSI mode full time
- Flight controls, check Elevator / Aileron
What are the FO scans - Runway Entry?
- Strobe ON
- Config Check
What are FO scans for - After Take Off Set Climb Power
When the PNF Calls Zero set (on flap retraction)
- PF will call set Climb Power
- PNF - Select SYNC on TMS (guard thrust levers)
- Engine Air On
- APU air off
- APU stop
- AC Pump Off
- Then reset climb power (normally about 88%, or 820 TGT)
What are FO scans for - Transition?
- Altimeter 1013.2
- Set altimeter bug to 0
- Set 1st and 2nd airspeed bugs togethor with VFTO bug
- External / logo light off
- Num 2 radio 121.5
What are FO scans for - Descent / Transition?
Descent
- Fuel check
- Pressurisation set
- Attitude Alert, Clearnace received
- TCAS down
- Radios set
Transition
- Altimeters to QNH
- Lights
What are FO scans for -After Landing?
- Flaps 0
- Trims set (5, or 3.5 up)
- TMS standby / off
- Radar off
- AC pump off
- APU start if required (including APU gen switch)
- Engine anti ice off
- Heaters, Ice detectors
- Air supply, as required
- Pack, as required
- Strobe - off on RWY Exit
- Cancel SAR, if required
What are FO scans for - After Shut down
- TCAS STBY
- Beacon Off
- Exterior lights, as required
- EFIS, dim or dim/off
What are the FO responses to “Call the Card?”
Captain - “Copied the info, Call the card”
FO
Captain - “Checked”
FO
Captain - “Set and cross checked”
FO
Captain - “Checked”
FO
Captain - “Copied the info, Call the card”
FO - “36 ton card, V1 VR, 109, 113”
Captain - “Checked”
FO - “V2 121”
Captain - “Set and cross checked”
FO - “VFTO, Ver, 160, 170”
Captain - “Checked”
FO - “Flexing at 36 in the Tref window, 88 my side, 93 across the top”
What are the FO scans for After Start?
- Airsupply, Packs & APU Air ON “Packs 1 and 2 on, APU air on”
- Monitor engines for bog down (while captain gets gens online)
- Heaters on
- Ice detector on
- Aircon on
- MWS check
What is the verbal que to start the after T/O flow?
PM - “Flap 0”
PF - “Set climb power”
