Data Sheets - Miscellaneous Other

Question 1

Define - Repair (key words) (510: 3.53)

Answer 1

Restore - Suitable

Question 2

Define - Alteration (key words) (510: 3.2)

Answer 2

Physical Change

Question 3

Define - RBI’s two Primaty Factors (510: 5.2)

Answer 3

Probability Consequence)

Question 4

Define - Location on vessel of Vessel MAWP (VIII: UG-98.a & 510: 3.37)

Answer 4

Top

Question 5

Define - Imperfection that exceeds the acceptance criteria (510: 3.15)

Answer 5

Defect

Question 6

Define - A flaw that may or may not exceed the acceptance criteria (510: 3.25)

Answer 6

Imperfection

Question 7

Design - Joint Category of a vessel longitudinal weld (VIII: Fig UW-3)

Answer 7

A

Question 8

Design - Joint Category of a vessel circumferential weld (VIII: Fig UW-3)

Answer 8

B

Question 9

Design - RT Factors representing Full RT (VIII: UG-116.e.1 & 2)

Answer 9

RT-1, RT-2

Question 10

Design - RT Factors representing Spot RT (VIII: UG-116.e.3)

Answer 10

RT-3

Question 11

Design - Weld Type - Butt Double Welded (VIII: Fig. UW-12)

Answer 11

Type 1

Question 12

Design - Weld Type - Butt Single Welded With Backing (VIII: Fig UW-12)

Answer 12

Type 2

Question 13

Design - Weld Type - Butt Single Welded Without Backing (VIII: Fig UW-12)

Answer 13

Type 3

Question 14

Design - Vessel service that always requires Full RT (VIII: UW-11.a.1)

Answer 14

Lethal

Question 15

Design - Maximum set pressure for single relief device on a vessel (VIII: UG-134.a)

Answer 15

MAWP

Question 16

Design - Marking on nameplate indicating vessel was PWHT (VIII: Fig UG-118)

Answer 16

HT

Question 17

Design - Marking on nameplate indicating vessel is in Lethal Service (VIII: UG-116.c)

Answer 17

L

Question 18

Design - ASME Sect VIII stamp for routine vessels (VIII: UG-116.a.1.a)

Answer 18

U

Question 19

Design - ASME Sect VIII stamp for miniature vessels (VIII: UG-116.a.1.b)

Answer 19

UM

Question 20

Design - ASME Sect VIII stamp for relief devices (VIII: Fig UG-129.1)

Answer 20

UV

Question 21

NDE - Number of CMLs to obtain thickness readings during inspection (key word) (510: 5.6.2.1)

Answer 21

Representative

Question 22

NDE - Number of Nozzles to obtain thickness readings during inspection (key word) (510: 5.6.2.1)

Answer 22

Representative

Question 23

NDE - Lead letter used during RT to check for backscatter radiation (V: T-223)

Answer 23

B

Question 24

NDE - Lead letter used during RT to indicate a film-side IQI (V: T-277.1.b)

Answer 24

F

Question 25

NDE - Hole size that must be visible in RT when using a hole-type IQI (V: T-283.1)

Answer 25

2T

Question 26

NDE - Two primary gamma-ray RT sources (577: 9.8.4)

Answer 26

Ir 192, Co 60

Question 27

Relief Valves - How relief devices should be transported (576: 5.8.4.2)

Answer 27

Upright

Question 28

Relief Valves - How relief device intervals are determined (key word) (510: 6.6.2.1)

Answer 28

Performance

Question 29

Welding - Variables needed on WPS (IX: QW-200.1.b)

Answer 29

Essential & Non-Essential

Question 30

Welding - Variables needed on PQR (IX: QW-200.2.b)

Answer 30

Essential

Question 31

Welding - Processes that can be used when substituting Preheat or Controlled Deposition welding for a required PWHT (510: 8.1.6.4.2.2.1.b & 510: 8.1.6.4.2.3.c)

Answer 31

SMAW, GMAW, GTAW

Question 32

Welding - Minimum taper required for shell welds with mismatch (VIII: UW-9.c)

Answer 32

3 to 1

Question 33

Weld Qualification - The “all position” test coupon (IX: QW-461.9)

Answer 33

6G

Question 34

Weld Qualification - Rejectable in RT when qualifying a welder (IX: QW-191.1.2.2.a.1)

Answer 34

Crack, Lack of Fusion, Incomplete Penetration

Question 35

Weld Qualification - Which welding process can a welder NOT be qualified by RT (IX: QW-304)

Answer 35

GMAW - SC

Question 36

Weld Qualification - Maximum allowed thickness on a WPS based on the plate thickness (T) of a PQR test coupon (IX: QW-451.1)

Answer 36

2T