ATA31 - Indicating / Recording systems

Question 1

412. What happens when ND shows red circle with ‘MAP NOT AVAIL’ message ?
     MCDU failure
     ADIRS not aligned
     Engines not running

Answer 1

ADIRS not aligned

Question 2

413. Can you read optional DATA (WPT or VOR.D, NDB,…) on ROSE VOR or ROSE ILS ?
     Yes
     No

Answer 2

No

Question 3

414. FAC’S calculate speed trend and VLS. The extremities of the trend VECTOR or VLS
     SEGMENT indicates : speed value at the next 10 seconds and 1,23 VS1G with present
     setting, is it correct ?
     Yes
     No

Answer 3

Yes

Question 4

415. VLS indication is inhibited :
     During first 10 sec after LIFT-OFF
     With SPEED BRAKES extended
     Both answers are correct

Answer 4

During first 10 sec after LIFT-OFF

Question 5

416. Do the ‘CHECK ATT’ message appear on both PFD’S at the same time ?
     Yes
     No

Answer 5

Yes

Question 6

417. Select the correct statement :
     DMC 1 supplies DATA to PFD 1 / PFD 2
     DMC 1 supplies DATA to ND 1 / ND 2
     DMC 1 supplies DATA to PFD 1 / ND 1 / EWD

Answer 6

DMC 1 supplies DATA to PFD 1 / ND 1 / EWD

Question 7

418. What is the basic role of the DMC’S ?
     They compute and generate the images to be displayed on EFIS or ECAM
     Generation of audio warnings
     Generation of amber warnings

Answer 7

They compute and generate the images to be displayed on EFIS or ECAM

Question 8

419. Which ILS information is displayed on the ND in ROSE ILS MODE :
     G/S and LOC scales
     Deviation bar, selected ILS course, G/S and LOC scales
     Deviation bar, selected ILS course and G/S scales

Answer 8

Deviation bar, selected ILS course, G/S and LOC scales

Question 9

420. What is the meaning of “INVALID DATA” message on LCD screen ?
     Corresponding LCD is not energized
     Electrical supply is good and correponding DMC failed
     Electrical supply is good and correponding DMC failed + it is possible to obtain an
     image on again by switching EIS DMC

Answer 9

Electrical supply is good and correponding DMC failed + it is possible to obtain an
image on again by switching EIS DMC

Question 10

421. Which computer processes the RED warnings ?
     SDAC
     FWC
     DMC

Answer 10

FWC

Question 11

422. FAC’S compute VLS, F, S, shown on PFD according to the position of FLAP
     SELECTOR. Is the above statement correct ?
     Yes
     No

Answer 11

Yes

Question 12

423. On the horizon line, you find a cyan HDG or TRK symbol, is your FD P/B switched
     ON ?
     Yes
     No

Answer 12

No

Question 13

424. With RADAR selected ON, what can you read on ND about ANTENNA setting :
     TILT ANGLE
     TILT ANGLE + Manuel GAIN MODE

Answer 13

TILT ANGLE + Manuel GAIN MODE

Question 14

425. TRK-FPA is the selected MODE for AFS, the inertial FPV is normally on the horizon
     line. Could you see it in red colour :
     Yes
     No

Answer 14

No

Question 15

426. In case of PFDU failure, the PFD IMAGE is transfered to the NDU :
     Manually
     Automatically
     Either manually or automatically

Answer 15

Automatically

Question 16

427. RA gives height on PFD :
     At the botton of attitude sphere
     On the altitude scale
     Both indications

Answer 16

Both indications

Question 17

428. Could you find on PFD HDG SCALE a space between GREEN DIAMOND and ILS
     course pointer ?
     Yes
     No

Answer 17

Yes

Question 18

429. Can you read amber warnings on FMA part of your PFD ?
     Yes
     No

Answer 18

Yes

Question 19

430. If the UPPER ECAM DISPLAY is lost, the E/WD automatically transfers to LOWER
     ECAM DISPLAY, if a system display is required :
     It displays automatically
     Press and hold the RELEVANT SYSTEM P/B for a maximum of 3 minutes
     Switch OFF the corresponding ECAM DISPLAY selector

Answer 19

Press and hold the RELEVANT SYSTEM P/B for a maximum of 3 minutes

Question 20

431. Can you read the HDG on the PFD ?
     Yes
     No

Answer 20

Yes

Question 21

432. Altitude amber window appears flashing :
     When A/C goes below MDA
     When A/C deviates from its selected altitude or selected FL
     Both answers are correct

Answer 21

When A/C deviates from its selected altitude or selected FL

Question 22

433. In the event of no ADF 1 reception, with ADF 1 selected on ND :
     The bearing pointer disappears and ADF FLAG is displayed
     The bearing pointer disappears and station ID is replaced by red crosses
     The bearing pointer disappears and station ID is replaced by frequency

Answer 22

The bearing pointer disappears and station ID is replaced by frequency

Question 23

434. In ROSE NAV MODE with VOR 1 selected, what VOR information is displayed on the
     left hand ND if no course has been selected ? :
     Deviation bar, selected COURSE and the bearing pointer
     Bearing pointer only
     Deviation bar and selected course only

Answer 23

Bearing pointer only

Question 24

435. On the RAMP with APU RUNNING, PARK BRK is set ON. On MEMO display, PARK
BRK appears :
In GREEN
Not at all
In YELLOW (because of ACCU PRESS)

Answer 24

In GREEN