1506V Folding Quick- Don Mask(HC-130)

Question 1

Calendar inspection shall be performed how often

Answer 1

30 days

CGTO PG-85-00-310-A 5-9

Question 2

What accessory parts are repairable

Answer 2

electrical components, soldering, or replacement of corroded or broken connectors

CGTO PG-85-00-310A P. 5-10
MPC 354010.1 p 5

Question 3

Operational test

Answer 3

1. apply external power
2. O2 gauge reads 300-475 psi
3. lever 2-on, lever 3-100% O2, lever 4-normal, indicator 5- blinks white with each breath, lever 4-emergency, breathe 3 cycles, indicator 5- should indicate continuos O2 flow, indicator 5 shows black with no breath, flow lever 4- normal, diluter lever 3- normal, flow lever 4- test mask.

Question 4

Clean and disinfect mask

Answer 4

1. facepiece- public places
2. anti smoke goggles- warm solution of mild liquid detergent(ivory or lux) and water at a ratio of one half teaspoon of detergent for each gallon of water
3. allow goggles and mask to air dry at room temp for 15-20 min
4. apply anti-fog to inside of lens

MPC 354010.1 P. 7,8

Question 5

Mask markers

Answer 5

mark pilot, co pilot, and flight engineer masks with ruby red reflective tape, 3/4 in from end of hose

MPC 354010.1 P. 8

Question 6

Random Facts

Answer 6

43 lbs of force
use elastrator to install cable guides on the O2 hose
pull the dot fastener
KRYTOX 240 used to lubricate lens tongues

MPC?

Question 7

What modifications to the mask are allowed

Answer 7

There are no modifications authorized

CGTO PG-85-00-310A P. 5-9

Question 8

How do you store the mask

Answer 8

1. wipe clean and store in it approved container to keep clean,
   dry, and lint free
2. sanitize before storage
3. do not expose to excessive heat or direct sunlight
4. not stored where other flight gear will be stored on it
5. apply dust cover

CGTO PG-85-00-310A P. 5-11

Question 9

Which bottle is used with this mask

Answer 9

MA-1 emergency oxygen bottle

M13520.1C 5-22

Question 10

How does the valve hose and communication assembly consisting of an inhalation/exhalation valve connect to the mask and hard shell assembly

Answer 10

By means of a 3 pin bayonet connector

M13520.1C 5-24

Question 11

What is replaceable on the mask

Answer 11

The lens

M13520.1C 5-24

Question 12

How many cycles do you breathe normally for the inspect

Answer 12

3 cycles

MPC 354010.0 P.6

Question 13

What does the flow indicator blink with each breath

Answer 13

White

MPC 354010.1 P. 6

Question 14

What does the flow indicator blink when no oxygen is flowing by momentarily holding breath

Answer 14

Black

MPC 354010.1 P. 6

Question 15

What type of connector is used for the communication cable and plug assembly

Answer 15

U-179/U

MPC 354010.1 P. 10

Question 16

How many cable guides are there

Answer 16

7

MPC 354010.1 P. 10

Question 17

Stubborn contamination can be removed by wiping the area with a lint free cloth moistened with what

Answer 17

Isopropyl alcohol, TT-I-735 series 70% solution

MPC 354010.1 P. 11

Question 18

Do not do what?

Answer 18

1. Use water hotter than 140 F
2. Use clothing detergent
3. Submerge oxygen valve in water

MPC 354010.1 P. 12

Question 19

How do you clean the oxygen valve

Answer 19

Pour Isopropyl Alcohol into a container approx. 0.75 in, allow to dry for 15-20 minutes, use cotton q-tip with alcohol to remove stubborn residue

MPC 354010.1 P. 12

Question 20

Where do you attach the pull test fixture and how many pounds of force is needed

Answer 20

Bayonet ring of the hardshell facepiece subassembly
43 lbs

MPC 354010.1 P. 12/13

Question 21

What might be used to lubricate the lens tongues during lens installation

Answer 21

KRYTOX 240

MPC 354010.1 P. 15

Question 22

What force is required to check friction force by inserting male friction connector into an oxygen regulator mask

Answer 22

12-20 lbs pull

MPC 354010.1 P. 13

Question 23

How do you adjust the friction disconnect force

Answer 23

Spread the metal C ring with a screwdriver or by tightening the adjuster c ring

MPC 354010.1 P. 16

Question 24

What color reflective tape do you mark the pilot, co pilot, and flight engineer’s mask connector assemblies with

Answer 24

3/4 in ruby red

MPC 354010.1 p 8

Question 25

What is the maximum length and minimum length of the anti stretch cord

Answer 25

14.5 in- 23.5 in

MPC 354010.1 p 16

Question 26

Mask assemblies and operating procedures

Answer 26

1. 5 sub assemblies
2. no mods allowed
3. disinfect with public places towelette- face piece
4. clean the anti-smoke goggles with a warm solution of mild liquid detergent(ivory or lux) at a ratio of 1/2 teaspoon of detergent for each gallon of water.