Volume 1-UR Flashcards
TOs provide all of the following except (A) instructions (B) safety procedures (C) job control numbers (D) technical information
C. job control numbers
Simply stated, a TO is considered to be _ ______ ____
a military order
TOs are established, numbered, and issued in accordance with TO
00-5-1
Which type of TO covers installation, operation, maintenance, and handling of Air Force military systems?
operations and maintenance TOs
How are TCTOs used?
direct and provide instructions for modifying equipment
Which is not an authorized category of TCTOs? (A) Urgent action (B) Routine action (C) immediate action (D) Emergency action
D. emergency action
What type of TCTO is indicated by a border of alternating red diagonals and red X’s?
Urgent action
the first two digits in a TO number indicates the ……
major category in which the TO is grouped
To find the most current publication date of a TO, check ….
the TO index
You can use the online TO index to do all of the following except (A) find a TO from a known part number (B) find the security classification of a TO (C) determine which TO is used on a particular aircraft (D) identify NDI inspections applicable to your aircraft
D. identify NDI inspections applicable to your aircraft
the MIDAS is ….
a six-digit numbering system expressed a three elements of two digits each
What information will the NDI GS manual provide?
inspections
what type of equipment manual would contain calibration requirements for the equipment?
operation and service manual
A group assembly parts list has serval part numbers listed for a part you need. to determine which part number is right for your aircraft , you should refer to the ……
usable on code column to find the correct part number for your equipment
Where would you find information for recording and reporting a NDI technique to inspect a F-16C aircraft speed brake?
33B-1-1
you are tasked to do an inspection; however you only know the name of the part you are to inspect. to locate the applicable paragraph and figure number for the inspection, you would check the TO’s ……..
alphabetical index
While doing a job you find a mistake in a TO. this will require initiation of a Technical Manual Change Recommendation and Reply form. Who is responsible for this action?
You
What for do you use to submit a TO improvement?
AFTO Form 22
Which change recommendation priority must be answered within 40 calendar days?
Urgent
Which type change recommendation priority is used to recommend improvements to correct potential hazards?
Routine
Which TO contains complete instructions for maintain TOs?
00-5-1
Which form is used to label the binder edge of TO binders?
AFTO form 32
You need to order a new TO to be used by personnel on a regular basis. How would you go about this?
establish an ID requirement
The TO listing for your shop’s operational TO file will show you all of these except (A) who currently has one signed out (B) which TOs are in the operational file (C) if your TO has the most recent change (D) ID requirement for each TO on operation file
A. who currently has one signed out
Responsibility for consolidating all TO requests on an installation rests with the ….
personnel in TODO
With few exceptions, you must file TOs within a maximum of ….
5 workdays of receipt
To locate the effective date for a TO you are using, you check the…
Title page
A TO effective date is …
later than the basic date
During periodic inventories, what do you use to ensure accountability of every TO page?
LOEP (List of effective pages)
In which TO chapter would you find page 4-2?
4
File TO supplements in …..
reverse numerical order in front of the basic TO
Air force supplies and equipment are owned by the ….
American taxpayer
the purpose of the Air Force supply system is to
provide a means of purchasing, distributing, and controlling equipment/supplies used by the Air Force
the NCB code identifies the country ….
that assigned the identification number
what system is the most complete and can provide you with cross-referenced information on part numbers, national stock numbers, manufacturers, and suppliers for items in the supply system?
FEDLOG
What system is used to determine whether your NDI laboratory is authorized a piece of equipment?
AFEMS
What for is used to request or turn-in property?
AF Form 2005
What form is used to request an item not listed in the federal supply system?
DD form 1348-6
Which condition tag would be placed on a floor buffer to indicate that it is serviceable?
Yellow DD form 1574
Which condition tag would be used to indicate an x-ray unit has been condemned?
Red DD form 1577
Which condition tag would be placed on an eddy current unity being sent back to depot for repair?
Green DD form 1577-2
from the lowest to the highest, the three levels of maintenance capability are …
organizational, intermediate, depot
which level of maintenance would include routine inspections and servicing with fuel or oil?
organizational
which level of maintenance involves major repairs and overhaul?
depot
which inspection involves a thorough and searching inspection of an entire weapon system?
PE (periodic)
what inspection attempts to minimize the length of time an aircraft is down for inspection?
PH (phased)
which inspection is based on calendar days?
ISO (isochronal)
who can sign off a red x?
authorized personnel only
which maintenance symbol would be used to indicate a scheduled PE inspection is overdue?
red dash
which symbol signifies that a minor discrepancy exists?
red diagonal
Category 1 DRs (deficiency report) are not used to report conditions (A) that may cause death. (B) that may cause a major system loss (C) resulting from a nonconformance to specifications (D) which, if uncorrected, could unacceptably restrict combat readiness.
C. resulting from nonconformance to specifications
what level of DR submission is responsible for securing and identifying a DR exhibit?
Originator
what level of the DR submission process determines whether an investigation is required?
screening/action point
MDD (maintenance data documentation) is grouped into ……
on- and off-equipment categories
You would not find MDD rules in (A) aircraft maintenance manuals (B) TO 00-20 series TOs (C) Local instructions (D) TO 00-35D-54
D. TO 00-35D-54
Which is not a purpose for using codes in MDD? (A) security (B) accuracy (C) Simplicity (D) facilitation of data retrieval
A. Security
What key data element-used in the MDD system does not identify a specific piece of equipment? (A) workcenter code (B)work unit code (C) serial number. (D) ID number
A. workcenter code
which MDD code is used as the primary method of sorting information?
Work unit
The air force maintains a limited number of these MDD codes to simplify reporting?
how malfunctioned
what form is used to track and process rpair cycle assets and other parts?
AFTO Form 350
Which is not a maintenance inspector function? (A) Determine the final condition of a locally manufactured part (B) certify a part is restored to serviceable condition (C) Verify the quantity of modified parts is correct (D) Inspect the quality of a repair
C. verify the quantity of modified parts is correct
All engine data can be found on AFTO Form ____
781J
What is the correct format for entering a date in the 781 series forms?
YYYYMMDD
What 781 series form is used when you line through a current time or date due and enter a new date or time due?
781K
What automated MDD computer system uses over 25 COTS software products?
IMDS
What computer software technology forms the base for the IMDS?
windows
what automated MDD system allows for point-of-maintenance input using portable maintenance aids?
IMDS
Which MAJCOM developed the G081 automated MDD system?
Air Mobility Command
Which programs are considered the heart of G081 and update the database?
Input programs
The G081 computer system …. (A) has passwords that are assigned by the computer (B) is authorized to transmit certain classified data (C) is not authorized to transmit classified data (D) does not require users to have a user ID
C. is not authorized to transmit classified data
Which is not one of the three methods of removing accident causes? (A) safety engineering (B) education and training (C) developing safe habits (D) enforcing safety standards
C. developing safe habits
the minimum temperature required for a substance to initiate self-sustained combustion is known as the …..
ignition temperature
the danger from static electricity is highest during …..
cold, dry weather
AFOSH standards provide guidance concerning occupational safety, occupational health, and …..
fire prevention
What are the speed limits for general-purpose vehicles on the flightline and in parking areas respectively?
15mph; 5mph
unless otherwise authorized, the distance restrictions for backing or parking vehicles on the flightline are….
25ft in the front and 200ft to the rear of the aircraft
Unattended vehicles on the flightline must …. (A) be placed in neutral (B) have keys left in the ignition (C) have the lights left on (D) be locked
B. have keys left in the ignition
how big is the noise safety zone circle, depending on the type of aircraft and engine, which surrounds the aircraft?
300 to 400 feet
the general danger area from aircraft radar is a ….
50 foot radius in an arc of 100 degrees from the antenna
which is not considered a main structural component of an aircraft? (A) doors (B) wings (C) Fuselage (D) Landing gear
A. Doors
Engine position numbers on multiengine aircraft are assigned consecutively from the ….
tip of the left wing to the tip of the right wing
Where is the aircraft elevator located?
on the empennage
the movable flight control surface on a fighter aircraft that acts as both a stabilizer and an elevator is called the …
stabilator
Waterlines are assigned along the …
horizontal plane
The tie-down rings on AGE are normally attached to the …
frame
AGE power system components are not made from …. (A) steel (B) copper (C) aluminum (D) magnesium
B. copper
How are permanents joints on AGE enclosures normally attached?
riveted
how many standard marking are applied to all Air Force aircraft?
six
Where is the national star insignia applied to aircraft?
left and right fuselage, upper left and lower right wing
Where are station numbers located on fixed wing aircraft?
nose
Which is not an aircraft identification and safety marking? (A) ground handling marking (B) Emergency marking (C) servicing marking (D) Crew marking
D. crew marking
what symbol is used to indicate an installed ejection system?
Triangle with apex pointed down
Even though this safety marking may be small and subdued, it will alert you about a hazardous condition.
Warning text