Slideouts Flashcards

1
Q

What are 3 types of manual slide outs?

A

Tip-out
Manual
Crank

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

How is a cable slide supported?

A

With rollers or wear bar.

Cables are just for lateral travel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

How far can a cable slide travel?

A

Up to 60 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

How much deflection should the cable have on a cable slide out?

A

1/2” (1”total)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What are the 5 things you should check for on a cable slide?

A

-no kinked or pinched cables
-all cables align with exit holes in
frame
-properly adjusted cables and chains
-all cable but keepers are oriented properly
-all chain connector jam nuts are tight

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

How do you adjust a sofa slide?
Vertically?
In-out?

A

Vertically- two carriage bolts

“Out-in”- set screw on the stop block

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What is “walking” or racking”?

What can cause it?

A

Binding and can be caused by broken roll pins

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What does an above floor slide need if it has a double ram?

A

Must be connected by a cross shaft

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which slide type can be a flush floor design?

A

Through-frame slide only

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What is the spacing of the holes for adjust an electric actuator?

A

1” spacing

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

When does the electric actuator need to be adjusted?

A

Only if the threaded rod is too short to make the adjustment

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

How far from the wall opening should the end roller be for an In-wall slide
What should the middle rollers be spaced at?

A

6”

Every 24-36”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

How much bigger does the wall opening need to be then the slide room on and In-wall slide?

A

5-5.5”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

How much force should the motor brake withstand?

A

60 ft/lbs

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

How many amps can a slide motor pull?

A

Up to 30amps

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What should the measurements be from the outside edge of the column to the face of the gear rack on an In-wall slide

A

2 1/2 plus or minus and 1/8”

17
Q

How should the gear racks be mounted?

A

Parallel to less the 1/8 difference

18
Q

What happens when you remove power from the motor brake?

A

The wiring in the magnet will force the pressure plate and the disc against the brake plate

19
Q

How much free travel should a hydraulic slide have?

A

2”-3”

20
Q

What is a monoplex control system and how does it work?

A

A control system that will automatically stop at the in our out position. Just need to click the button and it will go till it senses an extra current draw from the motor

21
Q

Where is the monopoles system usually mounted and why?

A

Near the motor mechanism to minimize the length of heavy gauge wires

22
Q

How many wires does a rocket switch usually have and where do they go?

A

6 wires
1+6 ground
3/4 hot
2+5 motor

23
Q

What is located on the ground lead off the motor? And why?

A

A small resistor (0.02 ohms) so that the controller can sense the current

24
Q

How does the controller switch power to the motor of the mechanism?

A

With two double-pole, double-throw relays

25
Q

When the motor is started, what does the controller do?

A

Ignores the current for approximately 2 seconds to allow for the start up surge

26
Q

How is the current adjusted on the controller?
What happens if it’s set to high?
To low?

A

By the Pot.
If it’s set too low it may not go all the way out/in
If it’s set to high it will damage the mechanism or slide facia

27
Q

How much does the pot move?

A

270 degrees

28
Q

What must you use and do before adjusting the current limiter?

A

A non-metallic screwdriver and discharge static electricity before adjusting

29
Q

What should be the clearance from the slide room wall to the edge of the room opening for an in-wall slide?

A

2 7/8” +/-1/8

30
Q

What is the gear ratio for the in-wall slide motors?

A

300:1