Rivet Joint Layouts Flashcards

1
Q

What are the four basic steps to establish a basic layout for repair of aircraft skin?

A

Establish a reference, bisect a line, lay out a square or rectangle, lay out a corner radius.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

When making repairs, the corners of the damaged area or the repair patch will be rounded to a minimum of_____ radius.

A

1/4 inch

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is the purpose of rounding the corners of damaged areas or repair patches?

A

To relieve stress concentration that develop at sharp corners.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Where would you choose to use a raised head rivet?

A

Where aerodynamic smoothness is not required.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Where would you choose to used a countersunk rivet?

A

Where aerodynamic smoothness is of prime concern.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What would happen if you chose rivets of a softer alloy than the metal to be riveted?

A

Rivets would shear. (Using too small of a rivet will also cause shearing.)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What would happen if you chose rivets of a harder alloy than the metal to be riveted?

A

Distortion of the metal because of the pressure required to drive the rivet. (Using too large of a rivet diameter will also result in metal distortion.)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Rivet diameters (D) are sized in what fraction of an inch and what is the minimum diameter for aircraft structural repair?

A

1/32, 3/32

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Rivet lengths (RL) are sized in what fraction of an inch?

A

1/16

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What fraction of an inch are bucktails measured in and how do you determine the proper size it should be?

A

1/16, should be 1/2D high and 1 1/2D wide.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What is the minimum edge distance a raised head rivet should be to the nearest edge of the sheet metal?

A

2D

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is the minimum edge distance a countersunk head rivet should be to the nearest edge of the sheet metal?

A

2 1/2D

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What is the maximum edge distance for both types of rivets? (NOTE: Edge distance must always be in the simplest form.)

A

4D

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What is rivet pitch?

A

The distance between rivets in the same row measured from rivet center to rivet center.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What is the minimum and maximum of RP and what is the normal working range?

A

4D-10D, 6D-8D

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

When two or more rows of rivets are used in a repair job, why are the rivets are staggered?

A

To obtain maximum strength.

17
Q

What is the distance between rows of rivets called?

A

Transvers Pitch (TP)

18
Q

Transverse pitch is normally 75% of existing rivet pitch, but should never be less than what?

A

2 1/2D