INTRO Chap 4 Flashcards

1
Q

One of the most important rules about working with power tools is to always what?

A

Disconnect the power source for any tool before you replace parts.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Any replacement part such as what? 3 bbd

A

Bits
Blades
Discs

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Always ———-the power source before you perform maintenance on any tool.

A

Disconnect

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Never activate the ——— on any power tool

A

Trigger lock

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Tools powered by electricity.

A

Electric tools

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Electric tools are operated either an——- or a ——–

A

Alternating current

Direct current

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Alternating current source

A

Wall receptacle

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Direct current source

A

battey

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Tools powered by fluid pressure

A

Hydraulic tools

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

2 things used to produce fluid pressure.

A

Hand pumps

Electric pumps

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Examples of hydraulic tools

A

Pipe benders
jack hammers
Porta-powers

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

All bits are held in the drill by the what

A

drill chuck

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Chucks can either be

A

Keyed

Keyless

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

To prevent any shock, operate only those tools that are ————– with proper —————

A

Double insulated

Ground fault protection

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Device protects the equipment from continued electrical current in case of a circuit fault.

A

Ground Fault Circuit Interrupter (GFCI)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The GFCI monitors the current flow and opens the circuit (which stops the flow of electricity) if it detects a difference between positive and negative flow.

A

T

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

How long does the interruption typically takes place

A

less than 1/10 of a second

18
Q

Make sure the drill bit is ——-in the chuck before you start the drill.

A

Tightened.

19
Q

Keep the drill’s air vent ——-with a small brush or small stick.

20
Q

Crucial to the maintenance and safety of a drill.

21
Q

Powered by compressed air from an air hose.

A

Pneumatic drills

22
Q

Pneumatic drills have many of the same parts, controls and uses as electric drills.

23
Q

When is the Pneumatic drill typically used?

A

When there is no source of electricity.

24
Q

The blade of a circular saw is protected by —– —–

25
On top of a circular guard, a rigid plastic guard protects you from ----------- & ----------------
Flying debris Touching the spinning blade (if you lean forward accidentally.)
26
Saber saws are sometimes reffered as ------------
Jig Saws
27
Saber saws have
very fine blades
28
The Saber saw is very effective for doing --------- &-------------
Delicate | Intricate
29
Saber saws can cut our patterns or irregular shapes from wood or thin, soft metals.
T
30
Before you plug the saw into a power source, make sure the switch is what
in the OFF position
31
The miter saw is what?
Miter Box + Circular Saw
32
The miter saw can make what?
Straight and miter cuts.
33
3 types of grinders?
Angle End Detail
34
Used to grind away hard, heavy materials and to grind surfaces such as pipes, plates or welds.
Angle Grinders
35
Always use the ----------- as a support when you are grinding or beveling metal pieces.
Adjustable tool rest
36
( Bench Grinder) There should be a maximum gap of --------- between the tool rest and the wheel and ---------- between the top guard and wheel.
1/8" | 1/4"
37
Make sure the ---------is placed on a secure surface.
bench grinder
38
When using a power nailer, 1st step is to ... Also wear what...........
Read the manufacturer's instructions before using a pneumatically powered nailer. Wear appropriate personal protective equipment.
39
Keep the nailer oiled according to the............
manufacturer's recommendations.
40
If the nailer is not firing,----------
disconnect the air hose before you attempt repairs.
41
For an air impact wrench...
Keep your body stance balanced
42
Air impact wrench is aka
impact wrench.