CHAIN AND SPROCKET DRIVE Flashcards

1
Q

A drive system consists of an endless
chain whose links engage the teeth of
sprocket keyed to the shaft of the
driving and driven mechanism that is
commonly used for power tiller
transmission boxes.
a. Roller chain drive
b. Pintle chain drive
c. Bead chain drive
d. None of the above

A

Roller chain drive

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Chain size is usually specified in terms
of ___.
a. diameter of roller chain
b. length of chain
c. roller chain number
d. None of the above

A

roller chain number

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

RC-50 chain is stronger than ___.
a. RC-60
b. RC-40
c. RC-70
d. None of the above

A

RC-40

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

The minimum size of chain for the
transmission box of a walking-type hand
tractor.
a. ANSI chain number 40
b. ANSI chain number 50
c. ANSI chain number 60
d. All of the above

A

ANSI chain number 50

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

The slack strand for chain with
horizontal center should be located at
the ___.
a. upper side
b. lower side
c. both sides
d. None of the above

A

lower side

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

If roller chain number 40 is to be
replaced with no. 60, the strength of the
chain will___.
a. decrease
b. increase
c. remain except the size
d. None of the above

A

increase

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

For slow-speed operation, the
recommended number of teeth for driver
sprocket is ___.
a. 11 teeth
b. 16 teeth
c. 24 teeth
d. None of the above

A

16 teeth

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

The recommended minimum number of
sprocket teeth for high-speed operation.
a. 14-16 teeth
b. 18-24 teeth
c. 28-30 teeth
d. None of the above

A

18-24 teeth

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

If the chain pitch is 12.7 mm, what is the
length of the chain needed for the drive in
Item above?
a. 100 pitches
b. 120 pitches
c. 140 pitches
d. None of the above

A

140 pitches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

The length of chains is usually expressed
in ___.
a. inches
b. meters
c. pitches
d. None of the above

A

pitches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Which of the following is not a
part of the roller chain
construction?
a. Rollers
b. Pins
c. Outside link plates
d. Inside link plates
e. None of the above
f. All of the above

A

NOTA

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

It is connecting link assembly for
easy and rapid replacement of parts
of chain drive.
a. Pin link
b. Link plate
c. Retainer
d. All of the above
e. Two of the above

A

AOTA

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Pitch length of roller chain number
35.
a. 1/4 in.
b. 3/8 in.
c. 1/2 in.
d. 1 in.
e. None of the above

A

3/8 in.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Pitch length of roller chain 25.
a. 1/4 in.
b. 3/8 in.
c. 1/2 in.
d. 1 in.
e. None of the above

A

1/4 in.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Pitch length of RC 40.
a. 1/4 in.
b. 3/8 in.
c. 1/2 in.
d. 1 in.
e. None of the above

A

1/2 in.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Pitch length of RC 60.
a. 3/8 in.
b. 1/2 in.
c. 3/4 in.
d. None of the above

A

3/4 in.

17
Q

Pitch length of RC 80
a. 1/4 in.
b. 1/2 in.
c. 3/4 in.
d. 1 in.
e. None of the above

A

1 in.

18
Q

It is a profiled wheel with teeth that
meshes with a chain, track or other
perforated or indented material.
a. Gear
b. Sprocket
c. Sheave
d. None of the above

A

Sprocket

19
Q

Chain measurement can be identified
based on ________ .
a. Pitch
b. Width between inner plates
c. Roller diameter
d. All of the above
e. Two of the above

A

AOTA

20
Q

When ordering chain, ANSI standard
provides that chains are sold in ____ ft
boxes.
a. 5
b. 10
c. 15
d. None of the above

A

10

21
Q

ANSI Standard for Roller Chain 40-1
means that the chain is _____ .
a. 4/8 in. pitch, single strand
b. 4/4 in. pitch, one piece
c. 4/2 in. pitch, first series
d. None of the above

A

4/8 in. pitch, single strand