Built-In Effects Processing Flashcards
Why don’t you need to be concerned about DSP consumption when adding a dynamics processor to an Input Channel?
The DSP used for the on-board dynamics is pre-allocated when you configure the number of Input Channels to use for your show.
How would you go about copying all compressor/limiter settings and expander/gate settings from a source channel to a destination channel? (
- Target source channel to ACS.
- Right-click on-screen Dynamics Graph.
- Choose ‘Copy Dynamics Settings’.
- Target destination channel to ACS.
- Right-click on-screen Dynamics Graph.
- Choose ‘Paste Dynamic Settings’.
In what order do the dynamic processors occur in the signal path?
Expander/Gate processor always follows the Compressor/Limiter processor.
How would you select multiple channels in order to paste dynamic settings?
Select the destination channels using Multi-Select or shift-clicking in the software.
What do the Presets icons look like in the VENUE software?
Folders.
What do the Presets icons enable you to do?
Store and load settings as presets.
How many bands of parametric EQ are available on Input Channels? (2)
2-band and 4-band.
How many bands of parametric EQ are available on FX Returns?
2-band.
What EQ mode must be active in order to toggle the outer parametric EQ bands between Bell and Shelf modes?
Digital mode.
Does the HPF change when the EQ is switched between Digital and Analog mode?
No.
How do you access Q or Bandwidth in the SC48 Channel Control section?
Press a band’s Frequency encoder.
Where can VENUE’s Graphic EQs be used?
Any Output bus, including Mains, Groups, Auxes, and Matrixes.
On a D-Show or Profile, how do you toggle between Bell and Shelf EQ modes from the ACS?
Press a band’s Frequency encoder.
On an SC48, how do you toggle between Bell and Shelf EQ modes from the ACS?
Shift+press a Frequency encoder.
How do you control value using a mouse?
Click+drag up or down.
How many Graphic EQs are available for use in a VENUE system?
24.
What are the various allocations of Graphic EQs?
0, 8, 16, or 24.
Does VENUE need to reload the show if Graphic EQ allocation is changed?
Yes.
How can you bank Graphic EQ bands to the VENUE control surface?
By pressing the GEQ bank switches on the control surface.
What faders are used to display EQ bands of a GEQ?
The Input Faders.
What are some ways to reset Graphic EQ parameters? (3)
Hold ‘Default/Alt’ switch and press select switch on fader.
Right-click fader on-screen and choose ‘Reset to 0.0dB’.
Hold ‘Alt’ on keyboard and click on-screen fader.
What are some ways to reset the entire Graphic EQ to flat? (2)
Right-click anywhere in GEQ on-screen and choose ‘Reset GEQ Section’.
Hold ‘Default/Alt’ while running finger across ‘Select’ switches for all faders in each bank of GEQ bands.
How would you go about copying and pasting EQ settings from one Input Channel to another? (5)
- Right-click on-screen EQ section/EQ Graph.
- Choose ‘Copy EQ Settings’.
- Target destination Input Channel to ACS.
- Right-click on-screen EQ section/EQ Graph.
- Choose ‘Paste EQ Settings’.
How would you select multiple channels to paste EQ settings?
Select the destinations channels using Multi-Select or shift-clicking in the software.
What encoder can you use to scroll through presets in the EQ Presets window?
The Snapshots encoder.
What control surface includes a ‘Dyn Pre EQ’ switch at the top of the ACS?
The D-Show control surface.
What are some ways to select multiple channels at once? (2)
Shift-click additional channels.
Shift/Multi-Select additional channels.
What control surface includes a ‘Input Direct’ switch at the top of the ACS?
The D-Show control surface.
What controls will affect all multi-selected channels?
Fader movements.
Channel switches e.g. EQ In.
Dual-function rotary encoders e.g. Aux Sends.
