Ast2 shop maintenance Flashcards

This flashcard deck was created using Flashcardlet's card creator

0
Q

A completed apex connector strap will have a _ inch loop at each end?

A

4 inch

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
1
Q

What reference manual is used to perform fluorescent dye penetrate inspection of welds fo basket/litter?

A

TO 33B-1-1

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

How is an apex attached to the parachute apex?

A

With a larks head

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is the dimensions of the trail line bib?

A

14x18 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What length and type webbing is used for fabricating an ADS static line?

A

18ft 10in, 1in tubular webbing

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What type of stitching is use when modifying the ADS pilot parachute drogue?

A

E-thread 8 to 10 stitches per inch

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What color is the ADS reefing line cutters “removed before drop” streamer?

A

Yellow

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What size stainless steel cable is routed through the 12 parachute connector link and Riser assemble d-ring?

A

1/8th inch

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Who is responsible for determining if repairs may be performed to an ADS assembly?

A

Supervisory personel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

The raw edge of single patches sewn to an ADS canopy should be turned under _ inch.

A

1/2 inch

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What should you always try to anchor the patch to, when patching an ADS canopy?

A

One hem or seam

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

A 28 foot ADS canopy connector links yoke and plate assembly torques to?

A

20-25 inch pounds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What procedures should be followed when pyrotechnic storage temperatures exceed 100F?

A

Temp recorded in red ink

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

When inspecting a pyro locker, you notice that two boxes of signal flares are touching the wall. What is the proper distance from the wall when storing these devices?

A

6 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What grade of fuel is recommended to be used in the CG-P1B?

A

Unleaded

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The minimum fuel octane that may be used in the CG-P1B is?

A

77

16
Q

After gluing reflective tape, the raft shall remain undisturbed for a minimum of _ hours

A

12

17
Q

What are the shop air requirements for the inflatable maintenance area?

A

Shop air will be regulated, no higher than 40 psig air from a source that is filtered to ensure no oil or moisture is present

18
Q

What grade of reflective tape must be used on the LRU/20/A and the RSLR–1 life raft?

A

Solas grade tape

19
Q

What is the SEAS-1 mouthpiece cleaned with during the operational check?

A

Hot, clean water. No soap.

20
Q

How long is the static leak check for the SEAS-1?

A

Two hours

21
Q

What is the SEAS-1 mouthpiece disinfected with after the operational check?

A

70% isopropyl alcohol

22
Q

How are the individual flight gear serial numbers composed to track a members flight gear?

A

First three letters of members last name and last four of their SSN.

23
Q

Where does the completion of the annual aircrew flight gear inspection get recorded?

A

ALMIS EAL

24
Q

How long must the member stay immersed in water for the leak check on the anti-exposure garment?

A

15 min

25
Q

Flight suit will be the same number size as what?

What determines the length?

A

The flight suit will be the same number size as the flight jacket. Their height will determine the length of the suit.

26
Q

How are flight gloves sized?

A

A flight glove is the same size as the individuals flight boots size.

27
Q

When measuring for Anti-Exposure Garments the members should be wearing what?

A

Largest undergarments

28
Q

Stencils used for the ADR-8 liferaft tube measure _ inch (es)

A

1/2 in

29
Q

The correct PSI for a fully serviced SEAS-1 is _ PSI.

A

3000 Psi

30
Q

How often must the flight gear inspection take place?

A

Yearly

31
Q

(Pyro) Temperature is the most important factor affecting _ ?

A

Powder stability

32
Q

Which two types of maintenance are performed on the life rafts?

A

Calendar and special inspections.