12. Wireless Networking Flashcards
- You need to install wireless Internet access in an open warehouse environment. After installing the equipment, the technician notices varying strengths throughout the warehouse. How do you make sure there is full coverage?
a. Turn on broadcast key rotation
b. Change the encryption method used on all APs
c. Change the antenna placement
d. Use channel bonding
e. Use channel shaping
c. It is imperative that a good site survey is completed before you install your wireless network. Trying various types of antennas and their placements is key to covering the whole wireless area.
- Which of the following uses a certificate on both the server and client to provide the best wireless security with 802.1x (and is the hardest to implement)?
a. AES
b. TTLS
c. TLS
d. TKIP
c. TLS provides really good wireless security, but it’s hard to implement because you need to install a certificate on your server and also on all your clients. TTLS only uses a server-side certificate.
- What is the frequency range of the IEEE802.11g standard?
a. 2.4 Gbps
b. 5 Gbps
c. 2.4 GHz
d. 5 GHz
c. The IEEE 802.11b and IEEE 802.11g both run in the 2.4 GHz RF range.
- Which devices can interfere with the operation of a wireless network because they operate on similar frequencies? (choose two)
a. Copier
b. Microwave oven
c. Toaster
d. Cordless phone
e. IP phone
f. AM radio
b, d. If you are running 802.11b/g frequency, then you can receive interference from microwave ovens and cordless phones.
- Which wireless standard allows you to channel-bond to increase bandwidth and uses both the 2.4 GHz and 5 GHz frequencies?
a. 802.11b
b. 802.11g
c. 802.11a
d. 802.11n
e. 802.11ac
d. 802.11n uses channel-bonding of both the 2.4 GHz range and the 5 GHz range to get increased bandwidth of over 100 Mbps.
- Which of the following is considered a PAN?
a. AES
b. BSS
c. SSID
d. Bluetooth
d. Bluetooth works wirelessly to connect our phones, keyboards, and so on in small area, also known as personal area networks (PANs).
- How many non-overlapping channels are available in 802.11a?
a. 3
b. 12
c. 23
d. 40
b. The IEEE 802.11a standard provides up to 12 non-overlapping channels, or up to 23 if you add the 802.11h standard.
- What is the maximum data rate for the 802.11a standard?
a. 6 Mbps
b. 11 Mbps
c. 22 Mbps
d. 54 Mbps
d. The IEEE 802.11a standard provides a maximum data rate of 54 Mbps.
9.You need to install wireless on multiple floors of a large building and maintenance area. What is your first concern before installing the APs?
a. Authentication
b. Encryption
c. Channel overlap
d. AP configuration
c. If you have a large area to cover with wireless, you need to be concerned with channel overlap.
- What is the maximum data rate for the 802.11b standard?
a. 6 Mbps
b. 11 Mbps
c. 22 Mbps
d. 54 Mbps
b. The IEEE 802.11b standard provides a maximum data rate of up to 11Mbps
- You connect a new host to your company’s wireless network. The host is set to receive a DHCP address and the WPA2 key is entered correctly. However, the host cannot connect to the network. What can the problem be?
a. DNS is not configured on the host?
b. MAC filtering is enabled on the AP
c. The network has run out of wireless connections
d. The host is enabled to run 802.11b and 802.11g
b. If everything is configured correctly on the host, then MAC filtering would stop the host from connecting to the AP. If you try to connect and it can’t, check the AP settings.
- Which is the highest encryption that WPA2 can use?
a. AES-CCMP
b. PPK via IV
c. PSK
d. TKIP/MIC
a. The IEEE 802.11i standard replaced Wired Equivalent Privacy (WEP) with a specific mode of Advanced Encryption Standard (AES) known as the Counter Mode Cipher Block Chaining-Message Authentication Code (CBC-MAC) protocol. This allows AES-Counter Mode CBC-MAC Protocol (AES-CCMP) to provide both data confidentiality (encryption) and data integrity.
- Which additional configuration step is necessary in order to connect to an access point that has SSID broadcasting disabled?
a. Set the SSID value in the client software to public.
b. Configure open authentication on the AP and the client.
c. Set the SSID value on the client to the SSID configured on the AP.
d. Configure MAC address filtering to permit the client to connect to the AP.
c. If you disable SSID broadcasting, which you should, then you must configure the SSID name on the clients that need to connect to the AP.
- Which spread-spectrum technology does the 802.11b standard define for operation?
a. IR
b. DSSS
c. FHSS
d. DSSS and FHSS
e. IR, FHSS, and DSSS
b. The IEEE 802.11b standard uses direct-sequence spread spectrum (DSSS). If you are running 802.11g, it uses orthogonal frequency-division multiplexing (OFDM).
- Which wireless LAN design ensures that a mobile wireless client will not lose connectivity when moving from one access point to another (roaming)?
a. Using adapters and access points manufactured by the same company.
b. Overlapping the wireless cell coverage by at least 10 percent.
c. Configuring all access points to use the same channel.
d. Utilising MAC address filtering to allow the client MAC address to authenticate with the surrounding APs.
b. If you are running an extended service set (meaning more than one AP with the same SSID), you need to overlap the cell coverage by 10 percent or more so clients will not drop out while roaming.