Truck Electrical Circuit Service 190404b Flashcards

1
Q
  1. All electrical schematics are drawn in a de-energized condition and all the electrical
    components are drawn in their:
    a) closed position.
    b) open position.
    c) normal position.
    d) non-normal position.
A

c) normal position.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q
  1. List the five (5) components every truck electrical circuit must contain to be safe and
    functional.
    a)
    b)
    c)
    d)
    e)
A

a) voltage source
b) electrical conductors
c) control device
d) overcurrent protection device
e) load

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q
  1. Ohm’s Law is used in calculating values in electrical circuits.E is the symbol for
    Electromotive force measured in volts (V), I is the symbol for Intensity of current
    flow, measured in amperes (A) and R is the symbol for Resistance to current flow,
    measured in ohms (0) What is the correct mathematical expression for Ohm’s Law?
    a) E =Ix R
    b) I=E/R
    c) R = E/I
    d) all of the above
A

D) All of the above

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q
  1. When you are troubleshooting a malfunctioning truck lighting circuit, you use a
    process of eliminating circuit components that are not causing a problem in order to
    find the circuit component that is causing the problem. This process is called:
    a) calculating the electrical failure.
    b) picking the electrical failure.
    c) illuminating the electrical failure.
    d) isolating the electrical failure.
A

d) isolating the electrical failure.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q
  1. High electrical resistances in electrical circuits will cause voltage drops. Voltage
    drops that occur in truck lighting systems will cause light bulbs to:
    a) illuminate normally.
    b) illuminate dimly.
    c) illuminate brighter than normal.
    d) burn out
A

b) illuminate dimly.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q
  1. Manufacturers develop and publish ____ _____ to guide you through
    troubleshooting procedures.
A

Flow Charts

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q
  1. The electrical resistance values of all the components in the _______ _
    electrical circuit add together to form the total resistance value of the circuit.
A

series

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q
  1. The current draw across each leg of a ________ electrical circuit add
    together to form the total current draw for the entire circuit.
A

parallel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q
  1. An information —– —— allows the unit’s electronic control
    modules to communicate with each other.
A

data bus

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q
  1. The best way to repair a broken wire going to the air bag inflator module is:
    a) by using rosin core electrical solder.
    b) by using a heat shrink butt end connector.
    c) to never repair a wire in the air bag system.
    d) to follow manufacturer’s procedure on SRS wiring repairs.
A

d) to follow manufacturer’s procedure on SRS wiring repairs.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q
  1. When installing electrical accessories under the dash of the truck, make sure you do
    not splice into the:
    a) red labelled wire harness.
    b) blue labelled wire harness.
    c) white labelled wire harness.
    d) yellow labelled wire harness.
A

d) yellow labelled wire harness.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q
  1. To prevent any damage to the clockspring in the truck when removing a steering
    gear, you must ensure that:
    a) you are familiar with the operation of the SRS system.
    b) you have Centred the steering wheel before you disconnect the gear.
    c) prevent the steering wheel from rotating while the gear is disconnected.
    d) you perform all of the tasks listed above.
A

d) you perform all of the tasks listed above.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q
  1. What is installed in the connectors of an air bag circuit to help prevent accidental
    deployment?
    a) locking mechanisms
    b) shorting bars
    c) gold plated pins and terminals
    d) yellow labelling
A

b) shorting bars

How well did you know this?
1
Not at all
2
3
4
5
Perfectly