Final Test Study Flashcards

1
Q

During the disengagement process, the clutch release levers move the clutch release bearing.
True
False

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

An engine drive uses the spring controlled centrifugal clutch so as to allow for engine idling.
True
False

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Flywheel, clutch housing and transmission housing face runout checks are conducted to ensure components will be parallel to one another during operation.
True
False

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Which device allows a driveline to change in length during operation?
a. full round yoke
b. universal joint
c. half round yoke
d. slip joint

A

d. slip joint

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Universal joint working angles are not affected by driveline speed.
True
False

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

A basic driveline configuration has one shaft. More complex driveline configurations use:
a. a single shaft
b. belts and pulleys
c. multiple shafts
d. chains and sprockets

A

c. multiple shafts

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

The gear pitch line is used to divide the following gear tooth areas:
a. heel and toe
b. drive and coast
c. face and flank
d. fillet and profile

A

c. face and flank

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

When installed between a drive and driven gear, an idler gear affects speed and torque changes between the two gears.
True
False

A

False. Changes rotating direction.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which of the following gear ratios would be a reduction gear ratio?
a) 0.10:1
b) 1.00:1
c) 10.00:1
d) 1.00:2

A

c. 10.00:1

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Multiple countershaft transmissions use several housings. These housings are kept in alignment through the use of:
a) shouldered bolts.
b) precise doweling.
c) tapered plugs.
d) floating cap screws.

A

b) precise doweling.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

The formula for determining gear ratio is the number of teeth on the driven gear divided by the number of teeth on the drive gear.
True
False

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

The input shaft and gear:
a) deliver torque to the mainshaft gears.
b) are supported on bushings.
c) are driven by the clutch discs.
d) utilize a lip seal for sealing.

A

c) are driven by the clutch discs.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

The three speed auxiliary section provides:
a) 15 gear speeds.
b) 18 gear speeds.
c) 13 gear speeds.
d) 12 gear speeds.

A

d) 12 gear speeds.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Why are lithium ion batteries desirable for electric hybrid applications?
a) high discharge rates and low storage capacity.
b) high discharge rates and high storage capacity.
c) Low discharge rates and high storage capacity.
d) low discharge rates and low storage capacity.

A

c) Low discharge rates and high storage capacity.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The purpose of the range, splitter and deep reduction cylinders is to:
a) transmit the gearshift lever actions to shift the auxiliary section sliding clutches.
b) use the air signal to shift the main section sliding clutches.
c) use the air signal to shift the auxiliary section sliding gears.
d) use the air signal to shift the auxiliary section sliding clutches.

A

d) use the air signal to shift the auxiliary section sliding clutches.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The air filter/regulator generally regulates air to ________________ pressure.
a) 18 psi to 26 psi.
b) 58 psi to 63 psi.
c) 97 psi to 103 psi.
d) 120 psi to 130 psi.

A

b) 58 psi to 63 psi.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

The range cylinder is a double acting cylinder that uses a spring to hold it in the low position and air to shift it into the high position.
True
False

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

The transmission shift controller contains:
a) electronic control unit and dash display.
b) electronic control unit and operator shift console.
c) operator shift console and dash display.
d) main section electric shifter and range/splitter assemblies.

A

b) electronic control unit and operator shift console.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

Leaking output shaft seals, worn output shaft bearings and broken synchronizer pins are often an indication of a problem with the:
a) engine and transmission mounts.
b) clutch systems.
c) driveline.
d) shift mechanism.

A

c) driveline

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

Premature input shaft bearing failure or slip out in direct gear is often an indication of a problem with the:
a) engine and transmission mounts.
b) clutch systems.
c) driveline.
d) shift mechanism.

A

a) engine and transmission mounts.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

A visual inspection process is an integral part of the transmission disassembly procedure.
True
False

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

When establishing the buffer zone around a diesel electric hybrid, what is the recommended distance the cones be placed from each corner of the vehicle?
a) 0.5m
b) 1.0m
c) 1.5m
d) 2.0m

A

b) 1.0m

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

Regulated air is applied to keep the range in low and the splitter in low.
True
False

24
Q

What medium of stored energy is contained within an accumulator?
a) gaseous
b) fluid
c) fluid and gas
d) plasma

A

c) fluid and gas

25
The indicator light for the power takeoff system is activated by an engagement switch located in the shift valve. True False
False
26
What device does a full time transfer case use to prevent driveline windup? a) planetary gear set. b) typical differential assembly c) limited slip clutch pack d) windup clutch
a) planetary gear set.
27
On the air actuated power takeoff system, what is the air routed through before going to the air valve? a) pressure protection valve b) pressure regulator valve c) flow control valve d) the shift cylinder
a) pressure protection valve
28
PTO backlash must be measured between: a) the PTO input gear and the PTO output gear. b) the PTO input gear and the idler. c) the PTO input gear and the transmission drive gear. d) the transmission drive gear and the transmission input gear.
c) the PTO input gear and the transmission drive grear.
29
The gross combination weight rating refers to the: a) amount of weight each axle can carry. b) combined gross axle weight ratings for a vehicle. c) total combined gross axle weight ratings for a vehicle and it's trailers. d) amount a vehicle weighs empty.
c) total combined gross axle weight ratings for a vehicle and it's trailers.
30
The input shaft drives the helical drive gear through a set of splines. True False
False
31
Which components are attached to the drive axle housing? a) suspension components. b) wheels tires and hubs. c) carrier housing d) all of the above
d) all of the above
32
The temperature at which the truck should be shut down and the cause of the excessive heat established and repaired is: a) 160F b) 220F c) 250F d) 275F
c) 250F
33
When checking pinion bearing preload using a cord and a spring scale, record the reading required to start the assembly rolling. True False
False, force required to keep it rolling.
34
On a carrier assembly, if a thrust screw is used, mark the spot with the most ________________ the thrust screw side of the bevel gear. a) back face runout toward. b) back face runout away. c) radial towards. d) radial away from.
a) back face runout toward.
35
57. What type of controls regulate the flow of air conditioning refrigerant or heater coolant without driver input? a) active b) passive c) supplemental d) mandatory
b) passive
36
58. The maximum allowable filling limit for any refrigerant container is: a) 65% of its internal volume b) 75% of its internal volume c) 80% of its internal volume d) 90% of its internal volume
c) 80% of its internal volume
37
66. From what electrical terminal does the low beam headlight circuit receive electrical power? a) ignition switched terminal. b) constant power terminal c) safety power terminal. d) high power terminal
b) constant power terminal
38
68. What component prevents all warning lights from illuminating when one warning light is illuminated? a) fusible link b) buzzer c) relays d) isolating diodes
d) isolating diodes
39
69. A hall effect sensor sends an amperage signal to the ammeter by: a) measuring the current along the shunt. b) using an integrated circuit amplifier. c) reversing the current flow d) grounding the signal from the alternator.
b) using an integrated circuit amplifier.
40
74. High wear of brass bushings would be indicated in an oil analysis as high ppm of: a) copper and zinc b) copper and tin c) brass and copper d) tin and silver
a) copper and zinc
41
75. A metal fracture surface that indicates several beach marks and a final fracture area is best described as: a) a ductile fracture. b) a fatigue fracture. c) a brittle fracture. d) a beach fracture
b) a fatigue fracture
42
76. Prior to inspection, metal specimens taken from a failure must be thoroughly cleaned, preferably with a power wire wheel. True False
False
43
35.The three major components of a power steering system are the: a) pump, connecting lines and reservoir b) steering gear, connecting lines and reservoir c) relief valve, connecting lines and pump. d) reservoir, pump and steering gear.
d) reservoir, pump and steering gear.
44
36. In a rack and pinion steering system, the movement of the wheels is controlled through the upper steering arm. True False
False
45
38. After installing new king pin bushings you must ream the new bushings out. True False
False
46
41. Which of the following alignment measurements or angles are adjustable? a) toe and caster b) toe out on turns c) kingpin inclination d) camber and kingpin inclination
a) toe and caster
47
42) A cross tube that has been bent due to a collision with an obstacle in off road conditions will affect which alignment measurements or angles? a) caster b) camber c) toe out on turns d) toe
d) toe
48
43. When viewed from the front of the vehicle, both front tires appear to have positive camber. The tires are tilted: a) in at the top. b) out at the top c) forward. d) rearward
b) out at the top
49
44. The order in which the ECU instructs the modulator valve to control air pressure is: a) hold, reapply and exhaust. b) reapply, exhaust and hold. c) exhaust, hold and reapply. d) exhaust, reapply and hold.
c) exhaust, hold and reapply.
50
50. The function of an ABS modulator valve assembly include: a) transmitting signals to the ECU b) receiving signals from the ECU c) transmitting signals to the wheel speed sensors. d) receiving signals from the wheel speed sensors.
b) receiving signals from the ECU
51
54. R-134A refrigerant, when held at a gauge pressure of 1.9 psi, turns into a vapor at at temperature of: a) -30F b) -10F c) 30F d) 70F
b) -10F
52
56. When the air conditiong system contains a fixed expansion tube and an accumulator, the thermostatic switch may be replaced with a: a) ambient temperature switch. b) high pressure switch. c) clutch cycling switch. d) Binary switch
c) clutch cycling switch
53
58. The Binary switch acts like a: a) low pressure switch b) high pressure switch c) ambient temperature switch d) all of the above
d) all of the above
54
59. The maximum allowable filling limit for any refrigerant container is: a) 65% b) 75% c) 80% d) 90%
c) 80%
55
62. What percentage of ozone is concentrated in the stratosphere? a) 40% b) 70% c) 90% d) 100%
c) 90%
56
64. R134a refrigerant has an ODP of: a) 0 b) 2 c) 4 d) 8
a) 0