SY1108 MFD

Question 1

T/F The primary flight display (PFR) can be selected directly from any MFD display using either the PFR/HSD MOSB or Default display Switch on the FCP control stick

Answer 1

True

Question 2

"Which of the following MFD controls/displays is used to select the course displayed in the CRS window
A) Numeric menu display MOSBs
B) Course menu display MOSBs
C) Course select rocker switch
D) Manual heading select rocker"

Answer 2

C

Question 3

“Which of the following actions is the correct procedure for selecting the single letter ““B”” on the alphabetic menu?
A) Press ML-1 once
B) Press ML-1 once followed by MB-6 (next)
C) Press ML-1 twice delaying at least on second in between button depressions
D) Press ML-1 twice without delaying”

Answer 3

D

Question 4

“Which of the following methods can be used to clear/correct an invalid data entry or optiong selection that continues to blink after the validity test?
A) For Cyclical option selections, press the MOSB again to select another valid option
B) For menu entries, press the adjacent MOSB again to restart the data entry process and then reenter valid data
C) Press one of the other active MOSBs, which will clear the selection/entry and display the last valid option/data
D) All of the above”

Answer 4

D

Question 5

T/F The “arm” extending from the Nadir and Zenith symbols on the ADI always point in the direction of the nearest horizon, except at exactly 90 dive/climb angle when they point towards the ghost horizon

Answer 5

True

Question 6

“What do the minimum and maximum G values that are displayed with oversized ticks on the G meter scale idicate for a clean aircraft?
A) The absolute minimum/maximum G limits that remain unchanged during the flight
B) The current minimum/maximum G limits that are calculated and updated based on fuel quantity/maneuver
C) The current minimum/maximum Gs that have been obtained and recorded during the flight
D) the minimum/maximum G limits of the display scale”

Answer 6

B

Question 7

"Which type of intruder aircraft does the red square symbol represent on the EHSI/HSD TCAS display
A) Threat aircraft at RA level
B) Threat aircraft at TA level
C) Proximity Aircraft
D) Non-threat aircraft"

Answer 7

A

Question 8

"Which of the following TCAS display scales (range in NM) is the default setting?
A) 2.5
B) 5.0
C) 10
D) 20"

Answer 8

C

Question 9

“Which of the following is true when a PRL failure is detected?
A) A flashing AVIONICS caution message is displayed on the HUB and MFD
B) The detected failure is recoreded on both the PRL and MFL, which can be viewed ciw the MAL display
C) The detected failure will be removed from the PFL if it no longer exists, but it will remain on the MFL
D) All of the above”

Answer 9

D

Question 10

"Which o the following flight reference displays are available on the MFD backup display with MDP failure
A) EADI and EHSI
B) Indicated Airspeed
C) Pressure Altitude
D) All of the above"

Answer 10

A

Question 11

"How many training zones can be downloaded from the DTC and are available for display on the MFD HSD
A) 5
B) 10
C) 20
D) 40"

Answer 11

B

Question 12

“What information does the Divert mode Range (RNG) profile display?
A) The flight profile for an optimum climb/cruise best range airspeed and altitude to the currently selected steer point using minimum fuel
B) The flight profile intended to achieve maximum endurance at the current altitude and the time remaining to reach Bingo fuel
C) The flight profile intended to achieve maximum range at the current altitude and the time remaining to current steer point
D) The flight profile intended to achieve maximum range at the current altitude and the estimated fuel remaining over the current steer point”

Answer 12

D