OUTDATED EFIS, NAV and FMS*

Question 1

Where are the reference speeds, MDA, DH and barometric altimeter settings entered?

Answer 1

On the Air Data reference Panel (ARP).

Question 2

Pitot tubes P1 and P2 are pitot static tubes while pitot tube P3 is only a pitot tube.?

Answer 2

True

Question 3

ARHS initialization takes approximately how much time on the ground and how much time in flight?

Answer 3

70 seconds/10-35 seconds

Question 4

Where is the slip indicator located?

Answer 4

Below the roll pointer

Question 5

When DME hold is selected, what is displayed/removed from view on the PFD?

Answer 5

An amber H replaces the green NM indication and the identifier for the VOR is removed.

Question 6

What does the flight mode annunciator in the upper left corner of the PFD display?

Answer 6

Current active and armed Flight Director status

Question 7

On the ground, how long can the EFIS tubes be operated without AC power?

Answer 7

5 minutes due to cooling degradation

Question 8

What should be observed when the RA test button is pressed?

Answer 8

50 feet is indicated and the rising runway indicator appears.

Question 9

What should be done to display TCAS information on the MFD?

Answer 9

Press the TFC button on the Display Control Panel.

Question 10

What should the pilot do if their PFD display fails

Answer 10

Select PFD on the MFD display reversionary panel to display PFD information on the MFD

Question 11

What should occur if the ED1 screen fails?

Answer 11

ED 1 screen will appear on ED2 automatically

Question 12

With the failure of ED2, or the failure and automatic transfer of ED1, what happens to the EICAS Control Panel (ECP)?

Answer 12

ECP operation is inhibited and the status and synoptic pages are removed. It can be regained by using the MFD reversionary panel or the source selector panel.

Question 13

If the only operative ED is displaying a status or synoptic page and a warning message is generated by the DCU, what should occur?

Answer 13

The operable ED will revert to the primary page and the warning message will be displayed

Question 14

The color of the armed mode of the flight director is shown by a ___________ color on the PFD.

Answer 14

White

Question 15

Warning messages will be shown as a ______ message on the CAS..

Answer 15

Red

Question 16

Caution messages that appear on ED1 will be accompanied by a __________________.

Answer 16

Flashing Master Caution light, single chime and amber message

Question 17

What is the primary source of control of the MFD navigation formats, navigation sources and bearing source display?

Answer 17

The Display Control Panel (DCP)

Question 18

In the event of a Display Control Panel (DCP) failure, both MFDs can be controlled by one DCP if the proper selection is made on the __________________.

Answer 18

Source Selector Panel

Question 19

Where is the Radar Information Line displayed?

Answer 19

On the top of the MFD.

Question 20

Individual satellites can be deselected from use by entering the identifier for the satellite on the FMS GPS control page.

Answer 20

True.

Question 21

During a wind shear warning, you should increase pitch up to the Pitch Limit Marker (alpha-margin indicator).

Answer 21

False.

Question 22

The flight director will provide windshear escape guidance during both a windshear caution or a windshear warning from the EGPWS system.

Answer 22

False.

Question 23

If DME Hold is selected, you will not be able to use the VOR course information for ILS or VOR tracking if you select another frequency

Answer 23

False.

Question 24

How many ways can you change the setting of VHF NAV number one?

Answer 24

1. RTU2. Back Up Tuning Unit3. Radio Page on the FMS

Question 25

During a GPS approach, what allows you to continue the approach to the missed approach point.

Answer 25

When GPS APPR appears at the bottom of the NAV source info block on the PFD.

Question 26

What will happen to the bearing pointer display on the MFD if there is a signal loss?

Answer 26

The respective pointer will be removed from view.