Harness/Accesories ?'s Flashcards

1
Q

The leg straps on a class III parachute torso harness….

A

Prevent falling down out of the sling.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is the purpose of the torso harness canopy release?

A

Allows jettisoning of the parachute canopy/

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What position is a crew member in when you are fitting a harness?

A

Standing leaning forward.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Where and how should you position the chest strap when fitting the torso harness on a crew member?

A

10-12 in below the chin and tight.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

During a routine inspection of a torso harness, remove dirt and contaminants with….

A

A semi soft bristle brush.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

The frost canopy releases are actuated by what?

A

Pulling the locking lever up with a finer and pulling down on actuating lever.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

While in training mod the CYPRES updates ground pressure every how often?

A

30sec.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What could you use to hold Scot release cartridges or boosters on a table?

A

Cheese cloth pad.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What color streamer is attached to the back automatic parachute with a .25 second time delay cartridge?

A

Yellow.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

A red streamer installed on a BA parachute means it…

A

has a 1 sec automatic ripcord release time delay device.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What type pads are installed on the main body of the Scot automatic ripchord release to cushion sharp blows?

A

Honeycomb.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Which components make up the Scot automatic ripcord release cartridge housing?

A

Housing, snap ring, and anvil assembly.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

When performing the aneroid check on the Scot automatic ripcord release the automatic parachute release tester automatically arms the release at a simulated altitude of?

A

30000 ft.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What designated size rod would yo use to remove the cartridge and booster from the cartridge housing on the Scot automatic ripcord release?

A

.19 in diameter.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

When testing the Scot automatic ripcord release, be sure the serviceable range is between…

A

13000 - 15000

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The Scot release aneroid is leaking or defective if the edge is

A

not visible.

17
Q

How much movement is allowed in the power cable when inspection the Scot release?

A

None.

18
Q

What torque value is applied to the power cable nut and outer housing when you assemble the Scot automatic ripcord release?

A

100in/lbs

19
Q

When installing the Scot release power cable, which side do you insert the top ripcord pin into.

A

Beveled

20
Q

Which type stitch is used on the minimum survival kit?

A

Basting.

21
Q

How many minutes, of E O2 does the MD-1 have?

A

10.

22
Q

How do you fold the nylon binding tape of the harness when inspection the CRU-60 bracket?

A

Against the harness webbing edge of the right vertical strap.

23
Q

What should be the pressure of the MD-1 cylinder?

A

1800 psi

24
Q

What type of thread is used to attach the personnel lowering device hardware pocket to the main lift web?

A

Waxed No. 8/9.

25
Q

How many in of plastic tubing is installed over the hook blade knife?

A

3

26
Q

What kind of knot secures the MD-1?

A

Bow knot.

27
Q

What is used to install the MS-2000 pocket to the pack and harness assembly.

A

Size E nylon thread, 7-11 spi, 2 rows.

28
Q

Identify the extraction force required to remove the cable from the automatic survival kit actuator upper disconnect assembly.

A

25 +- 5 lbs.