Harness Accesories Flashcards

1
Q

What safety precaution must you take prior to testing a release?

A

Remove live cartridges/boosters.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Where should you not place live cartridges or boosters?

A

Where they can fall/ be confused with dummy cartridges.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is the altitude ranging preset by the manufacturer?

A

1400 +- 1000

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What prevents the firing pin from striking the time delay cartridge when the release is above the preset attitude?

A

Barometric aneroid.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Red cap =

A

1 sec

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Yellow cap =

A

.25 sec

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Blue cap =

A

.75 sec

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

White cap =

A

4-5 sec

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What purpose does the older primary booster cartridge on the Scot release serve?

A

give sufficient force and stroke to withdraw ripchord pins?

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

List the items located in the cartridge housing.

A

Housing, retaining snap ring, and anvil assembly.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Name the parts of the firing pin assembly.

A

Release sleeve, firing pin spring, firing pin.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is the function of the Scot release tester?

A

Establish altitude of the Scot release.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

How do you perform a diagnostic sequence check prior to testing the aneroid?

A

Switch it on.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What must be accomplished prior to performing the aneroid check?

A

Disarm/remove release.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What would you use to remove the booster and delay cartridge when the cartridge removal tool dosent work?>

A

.19 in diameter dummy cartridge removal tool.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What two items make up the dummy cartridge?

A

Dummy cartridge body/ primer cap.

17
Q

What is used to convert the digital pressure reading to altitude?

A

ALT-O-METER conversion chart.

18
Q

What altitude range must the scot release actuate to maintain servicability?

A

13000-15000 ft

19
Q

Why must you examine dummy cartridge after the aneroid test?

A

See if anvil dented it.

20
Q

What do you use to inspect threaded parts?

A

10X magnifine glass.

21
Q

How much movement is allowed during the power cable rotation test?

A

None.

22
Q

What pull force is required to release the arming knob?

A

20+-5 in/lbs.

23
Q

What do you inspect on the booster cartridge?

A

Condition of aluminum seals.

24
Q

What do you engage into the firing pin sear when assembling the arming cable?

A

Arming cable sear.

25
Q

How do you install the primary and booster cartridges in the cartridge housing breech?

A

Booster, then MAJCOM primary cartridge.

26
Q

How is the slip nut tightened to the main aneroid housing?

A

Bottom out then torque to 20+-5 in/lbs

27
Q

Which side of the power cable eye must the ripchord pin pass through?

A

Beveled side.

28
Q

Describe the proper location and position for tracking the arming knob guide.

A

Right harness keeper at 54 degree angle, arming know down.

29
Q

How long is the line on the PLD?

A

150ft.

30
Q

Where is the hook blade pocket?

A

Right front riser.

31
Q

What do you do if the MS-2000 fails a flash rate test?

A

Replace batteries and try again.

32
Q

When installing the MD-1 O2 cylinder what direction must the gauge face?

A

Up through opening.

33
Q

Describe how to tack the PLD pocket in place.

A

Permanently in 6 places.

34
Q

When removing the MD-1 why do you remove the wooden ball from the actuating cable of the O cylinder.

A

So you don’t have to pull it through the pack flap and check entire length of cable.