FLOWS

Question 1

ORIGINATING FLOW

Answer 1

AIRWORTHINESS ACCEPTANCE

1 - DCU (Display Controller Unit) – SET

• BARO SET………………………………. IN
• HSI………………………………………….. Compass/Arc
• BRG………………………………………… ON/OFF

2 - GLARESHIELD LIGHTS CONTROL PANEL – AS REQUIRED

3 - ADS PROBE HEATERS – AS REQUIRED

• ON is OAT at or below freezing and water/snow/ice present.

4 - REVERSIONARY PANEL – SET

• DISPLAYS Selector……………………AUTO
• SENSORS (ADS/IRS)………………..Pushed OUT

5 - PFD – NO FLAGS

6 - MFD – SET

• MFD Options ……………………………SET

7 - Audio Control Panel (ACP) and O2 Mask, Regulator – CHECKED

• MIC Button………………………….Push In (AUTO)
• SPKR…………………………………..OFF
• Regulator Control Knob…………100%
• TEST/RESET Button……………..Press and Hold
  
  • Verify a “blink” in the flow indicator
  • Verify Audible Oxygen Flow
  • Once Mask fully pressurizes, indicator must go out
  • Release TEST/RESET
  • Verify CREW OXY PRESS on MFD Status

8 - Alternate Gear Extension Compartment – CHECKED

• Alternate Gear Extension Lever………..Full Down
• Electrical Override Switch………………. NORMAL

Question 2

BEFORE START

FLOW

Answer 2

1 - CREW O2 – CHECKED

• Green for 3 crewmemebrs
• Cyan for 2 crewmembers
• Amber - Mx

2 - PFD – CHECKED

• FMA: Clear
• Airspeed Tape: No Speed Indicated
• EADI: Level and no Flags
• ALT SEL: Confirm Initial Altitude
• VSI: near 0
• Heading Bug: Runway Heading
• HSI: Departure course and NAV source selected

3 - MFD – CHECK

• Set/Verify desired MFD options: Radar, TCAS, NAVAIDS, etc.

Question 3

ENGINE START

FLOW

Answer 3

1 - SEAT BELT / SHOULDER HARNESS – ON

2 - BEACON – ON

3 - HYDRAULIC PUMP 3A – ON

4 - HYDRAULIC PUMP 1 – ON

5 - DOORS / WINDOWS – CLOSED & LOCKED

6 - TRANSPONDER – ON

Question 4

AFTER START FLOW

Answer 4

1 - FLAPS – SET

2 - APU – AS REQUIRED

3 - HYDRAULIC ELEC PUMP 1 – AUTO

4 - ADS PROBES HEATER button – PUSHED OUT

5 - FLIGHT CONTOLS – CHECKED on CP’s MFD

6 - ELECTRONIC DEVICES – AIRPLANE MODE L/R CP/FO

Question 5

BEFORE TAKEOFF FLOW

Answer 5

1 - PA (Cabin Announcement)

2 - CAB - Cabin Secure

3 - Brake Temps (Green on Status Page)

4 - CCD - Change Status Page back to MAP

5 - T/O CONFIG Button

Question 6

DESCENT FLOW (PF)

Answer 6

1 - ALTIMETERS…… SET

2 - SEAT BELT / HARNESS …… CHECKED

Question 7

DESCENT FLOW (PM)

Answer 7

1 - STERILE LIGHT……………… ON

2 - EXTERNAL LIGHTS ………. ON

3 - ALTIMETER …………………… SET / CROSSCHECKED

4 - SEAT BELT / HARNESS…… CHECKED

5 - DESCENT CHECKLIST …… COMPLETE

Question 8

AFTER LANDING SEQUENCE

Answer 8

1 - LIGHTS………… SET

2 - ANTI-ICE……… ON

3 - FLAPS………….. UP

4 - TRIM……………. SET (4.0)

5 - APU……………… AS REQUIRED

Question 9

BEFORE START (TO THE LINE) TASKS

Answer 9

• Verify FMS database is valid
• Initialize ACARS
• FFOD Paperwork
• Obtain ATIS
• Obtain Clearance
• Program MCDU
• Verify fixes (including crossing restrictions)
• Set Flight Guidance (including altimeter)
• Setup FD Pro
• WANT Briefing

Question 10

BEFORE START (BELOW THE LINE) TASKS

Answer 10

• Complete manifest
• Read takeoff data to Captain
• Set Pitch trim

Question 11

PRIOR TO DESCENT TASKS (PF)

Answer 11

• MCDU programming:
  
  • Load the STAR and approach.
• Set and cross-check following:
  
  • Minimums
  • Frequency
  • Course
  • WANT Briefing
• Set AUTOBRAKE
• Verify Approach and Landing Speeds

Question 12

PRIOR TO DESCENT TASKS (PM)

Answer 12

*

Question 13

SHUTDOWN

FLOW

Answer 13

1 - ANTI-ICE……… ON

2 - XPNDR………… STBY