Chapter 10 - Recreation Facilities Flashcards
In load or unload areas and on amusement rides, where compliance with 405.2 is not structurally or operationally feasible, ramp slope shall be permitted to be ____ maximum.
1:8 MAXIMUM
1002.2 Amusement Rides, Accessible Routes - Accessible routes serving amusement rides shall comply with Chapter 4.
EXCEPTIONS:
1. In load or unload areas and on amusement rides, where compliance with 405.2 is not structurally or operationally feasible, ramp slope shall be permitted to be 1:8 maximum.
2. In load or unload areas and on amusement rides, handrails provided along walking surfaces complying with 403 and required on ramps complying with 405 shall not be required to comply with 505 where compliance is not structurally or operationally feasible.
In load or unload areas and on amusement rides, handrails provided along walking surfaces complying with 403 and required on ramps complying with 405 shall not be required to comply with 505 where compliance is not structurally or _____________ ________.
OPERATIONALLY FEASIBLE
1002.2 Amusement Rides, Accessible Routes - Accessible routes serving amusement rides shall comply with Chapter 4.
EXCEPTIONS:
1. In load or unload areas and on amusement rides, where compliance with 405.2 is not structurally or operationally feasible, ramp slope shall be permitted to be 1:8 maximum.
2. In load or unload areas and on amusement rides, handrails provided along walking surfaces complying with 403 and required on ramps complying with 405 shall not be required to comply with 505 where compliance is not structurally or operationally feasible.
At amusement rides, a turning space complying with 304.2 and 304.3 shall be provided in ____ and ______ areas.
LOAD, UNLOAD
1002.3 Amusement Rides, Load and Unload Areas - A turning space complying with 304.2 and 304.3 shall be provided in load and unload areas.
At amusement rides, the _____ or ______ _______ of wheelchair spaces shall be stable and firm.
FLOOR, GROUND SURFACE
1002.4.1 Wheelchair Spaces in Amusement Rides, Floor or Ground Surface - The floor or ground surface of wheelchair spaces shall be stable and firm.
At amusement rides the floor or ground surface of wheelchair spaces shall have a slope not steeper than ____ when in the load and unload position.
1:48
1002.4.2 Wheelchair Spaces in Amusement Rides, Slope - The floor or ground surface of wheelchair spaces shall have a slope not steeper than 1:48 when in the load and unload position.
Floors of amusement rides with wheelchair spaces and floors of load and unload areas shall be ___________ so that, when amusement rides are at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus ____ inches and the horizontal gap shall be ____ inches maximum under normal passenger load conditions.
COORDINATED, 5/8 INCHES, 3 INCHES
1002.4.3 Wheelchair Spaces in Amusement Rides, Gaps - Floors of amusement rides with wheelchair spaces and floors of load and unload areas shall be coordinated so that, when amusement rides are at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (16 mm) and the horizontal gap shall be 3 inches (75 mm) maximum under normal passenger load conditions.
Where amusement ride floor gap compliance is not operationally or structurally feasible, _____, ______ ______, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall be provided.
RAMPS, BRIDGE PLATES
1002.4.3 Wheelchair Spaces in Amusement Rides, Gaps - Floors of amusement rides with wheelchair spaces and floors of load and unload areas shall be coordinated so that, when amusement rides are at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (16 mm) and the horizontal gap shall be 3 inches (75 mm) maximum under normal passenger load conditions.
EXCEPTION: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall be provided.
Where wheelchair spaces are provided in amusement rides, securement devices shall be permitted to _______ required clearances.
OVERLAP
1002.4.4 Wheelchair Spaces in Amusement Rides, Clearances - Clearances for wheelchair spaces shall comply with 1002.4.4.
EXCEPTIONS:
1. Where provided, securement devices shall be permitted to overlap required clearances.
2. Wheelchair spaces shall be permitted to be mechanically or manually repositioned.
3. Wheelchair spaces shall not be required to comply with 307.4.
Wheelchair spaces in amusement rides shall be permitted to be ___________ or ________ repositioned.
MECHANICALLY, MANUALLY
1002.4.4 Wheelchair Spaces in Amusement Rides, Clearances - Clearances for wheelchair spaces shall comply with 1002.4.4.
EXCEPTIONS:
1. Where provided, securement devices shall be permitted to overlap required clearances.
2. Wheelchair spaces shall be permitted to be mechanically or manually repositioned.
3. Wheelchair spaces shall not be required to comply with 307.4.
T /F - Wheelchair spaces in amusement rides shall not be required to comply with 307.4 (Protruding Objects).
TRUE
1002.4.4 Wheelchair Spaces in Amusement Rides, Clearances - Clearances for wheelchair spaces shall comply with 1002.4.4.
EXCEPTIONS:
1. Where provided, securement devices shall be permitted to overlap required clearances.
2. Wheelchair spaces shall be permitted to be mechanically or manually repositioned.
3. Wheelchair spaces shall not be required to comply with 307.4.
At amusement rides, wheelchair spaces shall provide a clear width of ____ inches minimum and a clear length of ____ inches minimum measured to ____ inches minimum above the floor surface.
30 INCHES, 48 INCHES, 9 INCHES
1002.4.4.1 Wheelchair Spaces in Amusement Rides, Width and Length - Wheelchair spaces shall provide a clear width of 30 inches (760 mm) minimum and a clear length of 48 inches (1220 mm) minimum measured to 9 inches (230 mm) minimum above the floor surface.
In amusement rides, where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient ___________ clearance for individuals using a wheelchair or mobility aid to enter and exit the ride.
MANUEVERING
1002.4.4.2 Wheelchair Spaces in Amusement Rides, Side Entry - Where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient maneuvering clearance for individuals using a wheelchair or mobility aid to enter and exit the ride.
At amusement rides, objects are permitted to protrude a distance of ____ inches maximum along the front of the wheelchair space, where located ____ inches minimum and ____ inches maximum above the floor or ground surface of the wheelchair space.
6 INCHES, 9 INCHES, 27 INCHES
1002.4.4.3 Wheelchair Spaces in Amusement Rides, Permitted Protrusions in Wheelchair Spaces - Objects are permitted to protrude a distance of 6 inches (150 mm) maximum along the front of the wheelchair space, where located 9 inches (230 mm) minimum and 27 inches (685 mm) maximum above the floor or ground surface of the wheelchair space. Objects are permitted to protrude a distance of 25 inches (635 mm) maximum along the front of the wheelchair space, where located more than 27 inches (685 mm) above the floor or ground surface of the wheelchair space.
At amusement rides, objects are permitted to protrude a distance of ____ inches maximum along the front of the wheelchair space, where located more than ____ inches above the floor or ground surface of the wheelchair space.
25 INCHES, 27 INCHES
1002.4.4.3 Wheelchair Spaces in Amusement Rides, Permitted Protrusions in Wheelchair Spaces - Objects are permitted to protrude a distance of 6 inches (150 mm) maximum along the front of the wheelchair space, where located 9 inches (230 mm) minimum and 27 inches (685 mm) maximum above the floor or ground surface of the wheelchair space. Objects are permitted to protrude a distance of 25 inches (635 mm) maximum along the front of the wheelchair space, where located more than 27 inches (685 mm) above the floor or ground surface of the wheelchair space.
Openings providing entry to wheelchair spaces on amusement rides shall be ____ inches minimum clear.
32 INCHES
1002.4.5 Wheelchair Spaces in Amusement Rides, Ride Entry - Openings providing entry to wheelchair spaces on amusement rides shall be 32 inches (815 mm) minimum clear.
One side of the wheelchair space in amusement rides, shall ______ an accessible route when in the load and unload position.
ADJOIN
1002.4.6 Wheelchair Spaces in Amusement Rides, Approach - One side of the wheelchair space shall adjoin an accessible route when in the load and unload position.
Where an amusement ride provides shoulder-to-shoulder seating, _________ seats shall be shoulder-to-shoulder with the adjacent wheelchair space.
COMPANION
1002.4.7.1 Wheelchair Spaces in Amusement Rides, Shoulder-to-Shoulder Seating - Where an amusement ride provides shoulder-to-shoulder seating, companion seats shall be shoulder-to-shoulder with the adjacent wheelchair space.
At amusement rides, where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with the shoulder alignment requirement shall be required to the _______ extent practicable.
MAXIMUM
1002.4.7.1 Wheelchair Spaces in Amusement Rides, Shoulder-to-Shoulder Seating - Where an amusement ride provides shoulder-to-shoulder seating, companion seats shall be shoulder-to-shoulder with the adjacent wheelchair space.
EXCEPTION: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable.
Where the interior width of the amusement ride is greater than ____ inches, seating is provided for more than ___ rider, and the wheelchair is not required to be ________ within the amusement ride, a companion seat shall be provided for ____ wheelchair space.
53 INCHES, ONE, CENTERED, EACH
1002.4.7 Wheelchair Spaces in Amusement Rides, Companion Seats - Where the interior width of the amusement ride is greater than 53 inches (1345 mm), seating is provided for more than one rider, and the wheelchair is not required to be centered within the amusement ride, a companion seat shall be provided for each wheelchair space.
A clear floor or ground space complying with 305 shall be provided in the ____ and ______ area adjacent to the amusement ride seats designed for transfer.
LOAD, UNLOAD
1002.5.1 Amusement Ride Seats Designed for Transfer, Clear Floor or Ground Space - A clear floor or ground space complying with 305 shall be provided in the load and unload area adjacent to the amusement ride seats designed for transfer.
The height of amusement ride seats designed for transfer shall be ____ inches minimum and ____ inches maximum measured from the surface of the load and unload area.
14 INCHES, 24 INCHES
1002.5.2 Amusement Ride Seats Designed for Transfer, Transfer Height - The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area.
Where openings are provided for transfer to amusement ride seats, the openings shall provide _________ for transfer from a wheelchair or mobility aid to the amusement ride seat.
CLEARANCE
1002.5.3 Amusement Ride Seats Designed for Transfer, Transfer Entry - Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat.
Wheelchair storage spaces complying with 305 shall be provided in or adjacent to unload areas for each required amusement ride seat designed for ________ and shall not _______ any required means of egress or accessible route.
TRANSFER, OVERLAP
1002.5.4 Amusement Ride Seats Designed for Transfer, Wheelchair Storage Space - Wheelchair storage spaces complying with 305 shall be provided in or adjacent to unload areas for each required amusement ride seat designed for transfer and shall not overlap any required means of egress or accessible route.
At amusement rides, a clear floor or ground space complying with 305 shall be provided in the load and unload area ________ to the ________ ______.
ADJACENT, TRANSFER DEVICE
1002.6.1 Transfer Devices for Use with Amusement Rides, Clear Floor or Ground Space - A clear floor or ground space complying with 305 shall be provided in the load and unload area adjacent to the transfer device.
The height of amusement ride transfer device seats shall be ____ inches minimum and ____ inches maximum measured from the ____ and ______ surface.
14 INCHES, 24 INCHES, LOAD, UNLOAD
1002.6.2 Transfer Devices for Use with Amusement Rides, Transfer Height - The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface.
Wheelchair storage spaces complying with 305 shall be provided in or _______ to unload areas for ____ required transfer device and shall not _______ any required means of egress or accessible route.
ADJACENT, EACH, OVERLAP
1002.6.3 Transfer Devices for Use with Amusement Rides, Wheelchair Storage Space - Wheelchair storage spaces complying with 305 shall be provided in or adjacent to unload areas for each required transfer device and shall not overlap any required means of egress or accessible route.
1003.2.1 Recreational Boating Facilities, Boat Slips. Accessible routes serving boat slips shall be permitted to use the exceptions in 1003.2.1.
EXCEPTIONS:
1. Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4.
2. Gangways shall not be required to comply with the maximum rise specified in 405.6.
3. Where the total length of a gangway or series of gangways serving as part of a required accessible route is 80 feet (24 m) minimum, gangways shall not be required to comply with 405.2.
4. Where facilities contain fewer than 25 boat slips and the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2.
5. Where gangways connect to transition plates, landings specified by 405.7 shall not be required.
6. Where gangways and transition plates connect and are required to have handrails, handrail extensions shall not be required. Where handrail extensions are provided on gangways or transition plates, the handrail extensions shall not be required to be parallel with the ground or floor surface.
7. The cross slope specified in 403.3 and 405.3 for gangways, transition plates, and floating piers that are part of accessible routes shall be measured in the static position.
8. Changes in level complying with 303.3 and 303.4 shall be permitted on the surfaces of gangways and boat launch ramps.
T / F - Accessible routes serving floating boarding piers shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in 1003.2.1.
TRUE
1003.2.2 Recreational Boating Facilities, Boarding Piers at Boat Launch Ramps - Accessible routes serving boarding piers at boat launch ramps shall be permitted to use the exceptions in 1003.2.2.
EXCEPTIONS:
1. Accessible routes serving floating boarding piers shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in 1003.2.1.
2. Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2.
3. Where the accessible route serving a floating boarding pier or skid pier is located within a boat launch ramp, the portion of the accessible route located within the boat launch ramp shall not be required to comply with 405.
Where the total length of the gangway or series of gangways serving as part of a required accessible route is ____ feet minimum, gangways shall not be required to comply with 405.2.
30 FEET
1003.2.2 Recreational Boating Facilities, Boarding Piers at Boat Launch Ramps - Accessible routes serving boarding piers at boat launch ramps shall be permitted to use the exceptions in 1003.2.2.
EXCEPTIONS:
1. Accessible routes serving floating boarding piers shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in 1003.2.1.
2. Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2.
3. Where the accessible route serving a floating boarding pier or skid pier is located within a boat launch ramp, the portion of the accessible route located within the boat launch ramp shall not be required to comply with 405.
T / F - Where the accessible route serving a floating boarding pier or skid pier is located within a boat launch ramp, the portion of the accessible route located within the boat launch ramp shall not be required to comply with 405.
TRUE
1003.2.2 Recreational Boating Facilities, Boarding Piers at Boat Launch Ramps - Accessible routes serving boarding piers at boat launch ramps shall be permitted to use the exceptions in 1003.2.2.
EXCEPTIONS:
1. Accessible routes serving floating boarding piers shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in 1003.2.1.
2. Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2.
3. Where the accessible route serving a floating boarding pier or skid pier is located within a boat launch ramp, the portion of the accessible route located within the boat launch ramp shall not be required to comply with 405.
Boat slips shall provide clear pier space ____ inches wide minimum and at least as long as the boat slips.
60 INCHES
1003.3.1 Recreational Boating Facilities, Boat Slip Clearance - Boat slips shall provide clear pier space 60 inches (1525 mm) wide minimum and at least as long as the boat slips. Each 10 feet (3050 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum.
Each ____ feet maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening ____ inches wide minimum.
10 FEET, 60 INCHES
1003.3.1 Recreational Boating Facilities, Boat Slip Clearance - Boat slips shall provide clear pier space 60 inches (1525 mm) wide minimum and at least as long as the boat slips. Each 10 feet (3050 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum.
Clear pier space shall be permitted to be ____ inches wide minimum for a length of ____ inches maximum, provided that multiple ____ inch wide segments are separated by segments that are ____ inches wide minimum and ____ inches long minimum.
36 INCHES, 24 INCHES, 36 INCHES, 60 INCHES, 60 INCHES
1003.3.1 Recreational Boating Facilities, Boat Slip Clearance - Boat slips shall provide clear pier space 60 inches (1525 mm) wide minimum and at least as long as the boat slips. Each 10 feet (3050 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum.
EXCEPTIONS:
1. Clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (915 mm) wide segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum.
2. Edge protection shall be permitted at the continuous clear openings, provided that it is 4 inches (100 mm) high maximum and 2 inches (51 mm) wide maximum.
3. In existing piers, clear pier space shall be permitted to be located perpendicular to the boat slip and shall extend the width of the boat slip, where the facility has at least one boat slip complying with 1003.3, and further compliance with 1003.3 would result in a reduction in the number of boat slips available or result in a reduction of the widths of existing slips.
Edge protection at boat slips shall be permitted at the continuous clear openings, provided that it is ____ inches high maximum and ____ inches wide maximum.
4 INCHES, 2 INCHES
1003.3.1 Recreational Boating Facilities, Boat Slip Clearance - Boat slips shall provide clear pier space 60 inches (1525 mm) wide minimum and at least as long as the boat slips. Each 10 feet (3050 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum.
EXCEPTIONS:
1. Clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (915 mm) wide segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum.
2. Edge protection shall be permitted at the continuous clear openings, provided that it is 4 inches (100 mm) high maximum and 2 inches (51 mm) wide maximum.
3. In existing piers, clear pier space shall be permitted to be located perpendicular to the boat slip and shall extend the width of the boat slip, where the facility has at least one boat slip complying with 1003.3, and further compliance with 1003.3 would result in a reduction in the number of boat slips available or result in a reduction of the widths of existing slips.
In existing piers, clear pier space shall be permitted to be located _____________ to the boat slip and shall extend the _____ of the boat slip, where the facility has at least one boat slip complying with 1003.3, and further compliance with 1003.3 would result in a reduction in the number of boat slips available or result in a reduction of the widths of existing slips.
PERPENDICULAR, WIDTH
1003.3.1 Recreational Boating Facilities, Boat Slip Clearance - Boat slips shall provide clear pier space 60 inches (1525 mm) wide minimum and at least as long as the boat slips. Each 10 feet (3050 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum.
EXCEPTIONS:
1. Clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (915 mm) wide segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum.
2. Edge protection shall be permitted at the continuous clear openings, provided that it is 4 inches (100 mm) high maximum and 2 inches (51 mm) wide maximum.
3. In existing piers, clear pier space shall be permitted to be located perpendicular to the boat slip and shall extend the width of the boat slip, where the facility has at least one boat slip complying with 1003.3, and further compliance with 1003.3 would result in a reduction in the number of boat slips available or result in a reduction of the widths of existing slips.
Boarding piers at boat launch ramps shall provide clear pier space ____ inches wide minimum and shall extend the full ______ of the boarding pier.
60 INCHES, LENGTH
1003.3.2 Recreational Boating Facilities, Boarding Pier Clearances - Boarding piers at boat launch ramps shall provide clear pier space 60 inches (1525 mm) wide minimum and shall extend the full length of the boarding pier. Every 10 feet (3050 mm) maximum of linear pier edge shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum.
Every ____ feet maximum of linear pier edge shall contain at least one continuous clear opening ____ inches wide minimum.
10 FEET, 60 INCHES
1003.3.2 Recreational Boating Facilities, Boarding Pier Clearances - Boarding piers at boat launch ramps shall provide clear pier space 60 inches (1525 mm) wide minimum and shall extend the full length of the boarding pier. Every 10 feet (3050 mm) maximum of linear pier edge shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum.
The clear pier space shall be permitted to be ____ inches wide minimum for a length of ____ inches maximum provided that multiple ____ inch wide segments are separated by segments that are ____ inches wide minimum and ____ inches long minimum.
36 INCHES, 24 INCHES, 36 INCHES, 60 INCHES, 60 INCHES
1003.3.2 Recreational Boating Facilities, Boarding Pier Clearances - Boarding piers at boat launch ramps shall provide clear pier space 60 inches (1525 mm) wide minimum and shall extend the full length of the boarding pier. Every 10 feet (3050 mm) maximum of linear pier edge shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum.
EXCEPTIONS:
1. The clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum provided that multiple 36 inch (915 mm) wide segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum.
2. Edge protection shall be permitted at the continuous clear openings provided that it is 4 inches (100 mm) high maximum and 2 inches (51 mm) wide maximum.
Boarding pier edge protection shall be permitted at the continuous clear openings provided that it is ____ inches high maximum and ____ inches wide maximum.
4 INCHS; 2 INCHES
1003.3.2 Recreational Boating Facilities, Boarding Pier Clearances - Boarding piers at boat launch ramps shall provide clear pier space 60 inches (1525 mm) wide minimum and shall extend the full length of the boarding pier. Every 10 feet (3050 mm) maximum of linear pier edge shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum.
EXCEPTIONS:
1. The clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum provided that multiple 36 inch (915 mm) wide segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum.
2. Edge protection shall be permitted at the continuous clear openings provided that it is 4 inches (100 mm) high maximum and 2 inches (51 mm) wide maximum.
Exercise machines and equipment shall have a clear floor space complying with 305 positioned for ________ or for use by an individual ______ in a wheelchair.
TRANSFER, SEATED
1004.1 Exercise Machines and Equipment, Clear Floor Space - Exercise machines and equipment shall have a clear floor space complying with 305 positioned for transfer or for use by an individual seated in a wheelchair. Clear floor or ground spaces required at exercise machines and equipment shall be permitted to overlap.
T / F - Clear floor or ground spaces required at exercise machines and equipment shall not overlap.
FALSE
1004.1 Exercise Machines and Equipment, Clear Floor Space - Exercise machines and equipment shall have a clear floor space complying with 305 positioned for transfer or for use by an individual seated in a wheelchair. Clear floor or ground spaces required at exercise machines and equipment shall be permitted to overlap.
List the permitted exceptions to fishing pier and platform accessible routes.
1, 2, 5, 6, 7, AND 8 OF 1003.2.1
1005.1 Fishing Piers and Platforms, Accessible Routes - Accessible routes serving fishing piers and platforms, including gangways and floating piers, shall comply with Chapter 4.
EXCEPTIONS:
1. Accessible routes serving floating fishing piers and platforms shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in 1003.2.1.
2. Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2.
Where the total length of the gangway or series of gangways serving as part of a required accessible route at fishing piers and platforms is ____ feet minimum, gangways shall not be required to comply with 405.2 (Ramp slope).
30 FEET MINIMUM
1005.1 Fishing Piers and Platforms, Accessible Routes - Accessible routes serving fishing piers and platforms, including gangways and floating piers, shall comply with Chapter 4.
EXCEPTIONS:
1. Accessible routes serving floating fishing piers and platforms shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in 1003.2.1.
2. Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2.
At least ____ percent of the railings, guards, or handrails shall be ____ inches maximum above the ground or deck surface.
25 PERCENT, 34 INCHES
1005.2.1 Fishing Piers and Platforms, Height - At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface.
T / F - Where a 42 inch high guard limiting the passage of a 4 inch sphere is provided, the guard shall not be required to comply with 1005.2.1.
TRUE
1005.2.1 Fishing Piers and Platforms, Height - At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface.
EXCEPTION: Where a guard complying with sections 1003.2.12.1 and 1003.2.12.2 of the International Building Code (2000 edition) or sections 1012.2 and 1012.3 of the International Building Code (2003 edition) (incorporated by reference, see “Referenced Standards” in Chapter 1) is provided, the guard shall not be required to comply with 1005.2.1.
34 inch high railings, guards, or handrails required to comply with 1005.2.1 shall be _________ throughout the fishing pier or platform.
DISPERSED
1005.2.1.1 Fishing Piers and Platforms, Dispersion - Railings, guards, or handrails required to comply with 1005.2.1 shall be dispersed throughout the fishing pier or platform.
T / F - Where railings, guards, or handrails complying with 1005.2 are provided, edge protection complying with 1005.3.1 or 1005.3.2 shall be provided.
TRUE
1005.3 Fishing Piers and Platforms, Edge Protection - Where railings, guards, or handrails complying with 1005.2 are provided, edge protection complying with 1005.3.1 or 1005.3.2 shall be provided.
At fishing piers and platforms, curbs or barriers shall extend ____ inches minimum above the surface of the fishing pier or platform.
2 INCHES
1005.3.1 Fishing Piers and Platforms, Curb or Barrier - Curbs or barriers shall extend 2 inches (51 mm) minimum above the surface of the fishing pier or platform.
The ground or deck surface of fishing piers and platforms shall extend ____ inches minimum beyond the inside face of the railing.
12 INCHES MINIMUM
1005.3.2 Fishing Piers and Platforms, Extended Ground or Deck Surface - The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing. Toe clearance shall be provided and shall be 30 inches (760 mm) wide minimum and 9 inches (230 mm) minimum above the ground or deck surface beyond the railing.
At fishing piers and platforms, toe clearance shall be provided and shall be ____ inches wide minimum and ____ inches minimum above the ground or deck surface beyond the railing.
30 INCHES, 9 INCHES
1005.3.2 Fishing Piers and Platforms, Extended Ground or Deck Surface - The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing. Toe clearance shall be provided and shall be 30 inches (760 mm) wide minimum and 9 inches (230 mm) minimum above the ground or deck surface beyond the railing.
At each fishing pier and platform location where there are ________, ______, or _________ complying with 1005.2.1, a _____ _____ __ ______ _____ complying with 305 shall be provided.
RAILINGS, GUARDS, HANDRAILS, CLEAR FLOOR OR GROUND SPACE
1005.4 Fishing Piers and Platforms, Clear Floor or Ground Space - At each location where there are railings, guards, or handrails complying with 1005.2.1, a clear floor or ground space complying with 305 shall be provided. Where there are no railings, guards, or handrails, at least one clear floor or ground space complying with 305 shall be provided on the fishing pier or platform.
Where there are no railings, guards, or handrails at fishing pier and platform location, at least one _____ _____ __ ______ _____ complying with 305 shall be provided on the fishing pier or platform.
CLEAR FLOOR OR GROUND SPACE
1005.4 Fishing Piers and Platforms, Clear Floor or Ground Space - At each location where there are railings, guards, or handrails complying with 1005.2.1, a clear floor or ground space complying with 305 shall be provided. Where there are no railings, guards, or handrails, at least one clear floor or ground space complying with 305 shall be provided on the fishing pier or platform.
At least one _______ _____ complying with 304.3 shall be provided on fishing piers and platforms.
TURNING SPACE
1005.5 Fishing Piers and Platforms, Turning Space - At least one turning space complying with 304.3 shall be provided on fishing piers and platforms.
Accessible routes serving _____ _______, ________ ______ _______, _______ ______, ________ _______ ______, ______ ________ at driving ranges, course _______ ________, golf car ______ _____, ___ ____ areas, and course ______ _____ shall comply with Chapter 4 and shall be 48 inches (1220 mm) wide minimum.
TEEING GROUNDS, PRACTICE TEEING GROUNDS, PUTTING GREENS, PRACTICE PUTTING GREENS, TEEING STATIONS, WEATHER SHELTERS, RENTAL AREAS, BAG DROP, TOILET ROOMS
1006.2 Golf Facilities, Accessible Routes - Accessible routes serving teeing grounds, practice teeing grounds, putting greens, practice putting greens, teeing stations at driving ranges, course weather shelters, golf car rental areas, bag drop areas, and course toilet rooms shall comply with Chapter 4 and shall be 48 inches (1220 mm) wide minimum. Where handrails are provided, accessible routes shall be 60 inches (1525 mm) wide minimum.
Where handrails are provided, accessible routes shall be ____ inches wide minimum.
60 INCHES MINIMUM
1006.2 Golf Facilities, Accessible Routes - Accessible routes serving teeing grounds, practice teeing grounds, putting greens, practice putting greens, teeing stations at driving ranges, course weather shelters, golf car rental areas, bag drop areas, and course toilet rooms shall comply with Chapter 4 and shall be 48 inches (1220 mm) wide minimum. Where handrails are provided, accessible routes shall be 60 inches (1525 mm) wide minimum.
Handrails shall not be required on ____ _______. Where handrails are provided on golf courses, the handrails shall not be required to comply with 505.
GOLF COURSES
1006.2 Golf Facilities, Accessible Routes - Accessible routes serving teeing grounds, practice teeing grounds, putting greens, practice putting greens, teeing stations at driving ranges, course weather shelters, golf car rental areas, bag drop areas, and course toilet rooms shall comply with Chapter 4 and shall be 48 inches (1220 mm) wide minimum. Where handrails are provided, accessible routes shall be 60 inches (1525 mm) wide minimum.
EXCEPTION: Handrails shall not be required on golf courses. Where handrails are provided on golf courses, the handrails shall not be required to comply with 505.
The clear width of golf car passages shall be ____ inches minimum.
48 INCHES MINIMUM
1006.3.1 Golf Car Passages, Clear Width - The clear width of golf car passages shall be 48 inches (1220 mm) minimum.
Where curbs or other constructed barriers prevent golf cars from entering a fairway, openings ____ inches wide minimum shall be provided at intervals not to exceed ____ yards.
60 INCHES, 75 YARDS
1006.3.2 Golf Car Passages, Barriers - Where curbs or other constructed barriers prevent golf cars from entering a fairway, openings 60 inches (1525 mm) wide minimum shall be provided at intervals not to exceed 75 yards (69 m).
A clear floor or ground space ____ inches minimum by ____ inches minimum shall be provided within weather shelters.
60 INCHES MINIMUM, 96 INCHES MINIMUM
1006.4 Golf Car Passages, Weather Shelters - A clear floor or ground space 60 inches (1525 mm) minimum by 96 inches (2440 mm) minimum shall be provided within weather shelters.
Playing surfaces shall not be required to comply with 302.2 (______).
CARPET
1007.2 Miniature Golf Facilities, Accessible Routes - Accessible routes serving holes on miniature golf courses shall comply with Chapter 4. Accessible routes located on playing surfaces of miniature golf holes shall be permitted to use the exceptions in 1007.2.
EXCEPTIONS:
1. Playing surfaces shall not be required to comply with 302.2.
2. Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum.
3. A slope not steeper than 1:4 for a 4 inch (100 mm) maximum rise shall be permitted.
4. Ramp landing slopes specified by 405.7.1 shall be permitted to be 1:20 maximum.
5. Ramp landing length specified by 405.7.3 shall be permitted to be 48 inches (1220 mm) long minimum.
6. Ramp landing size specified by 405.7.4 shall be permitted to be 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum.
7. Handrails shall not be required on holes. Where handrails are provided on holes, the handrails shall not be required to comply with 505.
Where accessible routes intersect playing surfaces of miniature golf holes, a ____ inch maximum curb shall be permitted for a width of ____ inches minimum.
1 INCH MAXIMUM, 32 INCHES MINIMUM
1007.2 Miniature Golf Facilities, Accessible Routes - Accessible routes serving holes on miniature golf courses shall comply with Chapter 4. Accessible routes located on playing surfaces of miniature golf holes shall be permitted to use the exceptions in 1007.2.
EXCEPTIONS:
1. Playing surfaces shall not be required to comply with 302.2.
2. Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum.
3. A slope not steeper than 1:4 for a 4 inch (100 mm) maximum rise shall be permitted.
4. Ramp landing slopes specified by 405.7.1 shall be permitted to be 1:20 maximum.
5. Ramp landing length specified by 405.7.3 shall be permitted to be 48 inches (1220 mm) long minimum.
6. Ramp landing size specified by 405.7.4 shall be permitted to be 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum.
7. Handrails shall not be required on holes. Where handrails are provided on holes, the handrails shall not be required to comply with 505.
At miniature golf holes, a slope not steeper than ____ for a ____ inch maximum rise shall be permitted.
1:4, 4 INCH MAXIMUM
1007.2 Miniature Golf Facilities, Accessible Routes - Accessible routes serving holes on miniature golf courses shall comply with Chapter 4. Accessible routes located on playing surfaces of miniature golf holes shall be permitted to use the exceptions in 1007.2.
EXCEPTIONS:
1. Playing surfaces shall not be required to comply with 302.2.
2. Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum.
3. A slope not steeper than 1:4 for a 4 inch (100 mm) maximum rise shall be permitted.
4. Ramp landing slopes specified by 405.7.1 shall be permitted to be 1:20 maximum.
5. Ramp landing length specified by 405.7.3 shall be permitted to be 48 inches (1220 mm) long minimum.
6. Ramp landing size specified by 405.7.4 shall be permitted to be 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum.
7. Handrails shall not be required on holes. Where handrails are provided on holes, the handrails shall not be required to comply with 505.
At miniature golf holes, ramp landing slopes specified by 405.7.1 shall be permitted to be ____ maximum.
1:20
1007.2 Miniature Golf Facilities, Accessible Routes - Accessible routes serving holes on miniature golf courses shall comply with Chapter 4. Accessible routes located on playing surfaces of miniature golf holes shall be permitted to use the exceptions in 1007.2.
EXCEPTIONS:
1. Playing surfaces shall not be required to comply with 302.2.
2. Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum.
3. A slope not steeper than 1:4 for a 4 inch (100 mm) maximum rise shall be permitted.
4. Ramp landing slopes specified by 405.7.1 shall be permitted to be 1:20 maximum.
5. Ramp landing length specified by 405.7.3 shall be permitted to be 48 inches (1220 mm) long minimum.
6. Ramp landing size specified by 405.7.4 shall be permitted to be 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum.
7. Handrails shall not be required on holes. Where handrails are provided on holes, the handrails shall not be required to comply with 505.
At miniature golf holes, ramp landing length specified by 405.7.3 shall be permitted to be ____ inches long minimum.
48 INCHES
1007.2 Miniature Golf Facilities, Accessible Routes - Accessible routes serving holes on miniature golf courses shall comply with Chapter 4. Accessible routes located on playing surfaces of miniature golf holes shall be permitted to use the exceptions in 1007.2.
EXCEPTIONS:
1. Playing surfaces shall not be required to comply with 302.2.
2. Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum.
3. A slope not steeper than 1:4 for a 4 inch (100 mm) maximum rise shall be permitted.
4. Ramp landing slopes specified by 405.7.1 shall be permitted to be 1:20 maximum.
5. Ramp landing length specified by 405.7.3 shall be permitted to be 48 inches (1220 mm) long minimum.
6. Ramp landing size specified by 405.7.4 shall be permitted to be 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum.
7. Handrails shall not be required on holes. Where handrails are provided on holes, the handrails shall not be required to comply with 505.
At miniature golf holes, ramp landing size specified by 405.7.4 shall be permitted to be ____ inches minimum by ____ inches minimum.
48 INCHES, 60 INCHES
1007.2 Miniature Golf Facilities, Accessible Routes - Accessible routes serving holes on miniature golf courses shall comply with Chapter 4. Accessible routes located on playing surfaces of miniature golf holes shall be permitted to use the exceptions in 1007.2.
EXCEPTIONS:
1. Playing surfaces shall not be required to comply with 302.2.
2. Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum.
3. A slope not steeper than 1:4 for a 4 inch (100 mm) maximum rise shall be permitted.
4. Ramp landing slopes specified by 405.7.1 shall be permitted to be 1:20 maximum.
5. Ramp landing length specified by 405.7.3 shall be permitted to be 48 inches (1220 mm) long minimum.
6. Ramp landing size specified by 405.7.4 shall be permitted to be 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum.
7. Handrails shall not be required on holes. Where handrails are provided on holes, the handrails shall not be required to comply with 505.
T / F - Handrails shall not be required on miniature golf holes. Where handrails are provided on holes, the handrails shall not be required to comply with 505.
TRUE
1007.2 Miniature Golf Facilities, Accessible Routes - Accessible routes serving holes on miniature golf courses shall comply with Chapter 4. Accessible routes located on playing surfaces of miniature golf holes shall be permitted to use the exceptions in 1007.2.
EXCEPTIONS:
1. Playing surfaces shall not be required to comply with 302.2.
2. Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum.
3. A slope not steeper than 1:4 for a 4 inch (100 mm) maximum rise shall be permitted.
4. Ramp landing slopes specified by 405.7.1 shall be permitted to be 1:20 maximum.
5. Ramp landing length specified by 405.7.3 shall be permitted to be 48 inches (1220 mm) long minimum.
6. Ramp landing size specified by 405.7.4 shall be permitted to be 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum.
7. Handrails shall not be required on holes. Where handrails are provided on holes, the handrails shall not be required to comply with 505.
A clear floor or ground space ____ inches minimum by ____ inches minimum with slopes not steeper than ____ shall be provided at the start of play.
48 INCHES, 60 INCHES, 1:48
1007.3.1 Miniature Golf Holes, Start of Play - A clear floor or ground space 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum with slopes not steeper than 1:48 shall be provided at the start of play.
All areas within holes where golf balls rest shall be within ____ inches maximum of a clear floor or ground space ____ inches wide minimum and ____ inches long minimum having a running slope not steeper than ____.
36 INCHES, 36 INCHES WIDE, 48 INCHES LONG, 1:20
1007.3.2 Miniature Golf Holes, Golf Club Reach Range Area - All areas within holes where golf balls rest shall be within 36 inches (915 mm) maximum of a clear floor or ground space 36 inches (915 mm) wide minimum and 48 inches (1220 mm) long minimum having a running slope not steeper than 1:20. The clear floor or ground space shall be served by an accessible route.
The clear floor or ground space at miniature golf holes shall be served by an __________ _____.
ACCESSIBLE ROUTE
1007.3.2 Miniature Golf Holes, Golf Club Reach Range Area - All areas within holes where golf balls rest shall be within 36 inches (915 mm) maximum of a clear floor or ground space 36 inches (915 mm) wide minimum and 48 inches (1220 mm) long minimum having a running slope not steeper than 1:20. The clear floor or ground space shall be served by an accessible route.
Where accessible routes serve ground level play components, the vertical clearance shall be ____ inches high minimum.
80 INCHES
1008.2 Play Areas, Accessible Routes - Accessible routes serving play areas shall comply with Chapter 4 and 1008.2 and shall be permitted to use the exceptions in 1008.2.1 through 1008.2.3. Where accessible routes serve ground level play components, the vertical clearance shall be 80 inches high (2030 mm) minimum.
Ground level play components shall be permitted to use transfer systems to connect ____ or less elevated play components. Where ____ or more elevated play components are provided, ____ percent of the elevated play components shall be permitted to be connected by transfer systems.
19 OR LESS, 20 OR MORE, 25 PERCENT
1008.2.1 Play Areas, Ground Level and Elevated Play Components - Accessible routes serving ground level play components and elevated play components shall be permitted to use the exceptions in 1008.2.1.
EXCEPTIONS:
1. Transfer systems complying with 1008.3 shall be permitted to connect elevated play components except where 20 or more elevated play components are provided no more than 25 percent of the elevated play components shall be permitted to be connected by transfer systems.
2. Where transfer systems are provided, an elevated play component shall be permitted to connect to another elevated play component as part of an accessible route.
T /F - Where transfer systems are provided, an elevated play component shall be permitted to connect to another elevated play component as part of an accessible route.
TRUE
1008.2.1 Play Areas, Ground Level and Elevated Play Components - Accessible routes serving ground level play components and elevated play components shall be permitted to use the exceptions in 1008.2.1.
EXCEPTIONS:
1. Transfer systems complying with 1008.3 shall be permitted to connect elevated play components except where 20 or more elevated play components are provided no more than 25 percent of the elevated play components shall be permitted to be connected by transfer systems.
2. Where transfer systems are provided, an elevated play component shall be permitted to connect to another elevated play component as part of an accessible route.
T /F - Soft contained play structures shall be permitted to use transfer systems as part of an accessible route.
TRUE
1008.2.2 Play Areas, Soft Contained Play Structures - Accessible routes serving soft contained play structures shall be permitted to use the exception in 1008.2.2.
EXCEPTION: Transfer systems complying with 1008.3 shall be permitted to be used as part of an accessible route.
Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is _________, compliance with 302, 403.3, 405.2, 405.3, and 1008.2.6 shall not be required.
SUBMERGED
1008.2.3 Play Areas, Water Play Components - Accessible routes serving water play components shall be permitted to use the exceptions in 1008.2.3.
EXCEPTIONS:
1. Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is submerged, compliance with 302, 403.3, 405.2, 405.3, and 1008.2.6 shall not be required.
2. Transfer systems complying with 1008.3 shall be permitted to connect elevated play components in water.
List the aspects of an accessible route, clear floor or ground surface, or turning space serving water play components that are not required to comply when the surface is submerged.
302 (Floor or Ground Surfaces)
403.3 (Clear Floor or Ground Slope)
405.2 (Ramp Slope)
405.3 (Cross Slope)
1008.2.6 (Ground Surfaces)
EXCEPTIONS:
1. Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is submerged, compliance with 302, 403.3, 405.2, 405.3, and 1008.2.6 shall not be required.
2. Transfer systems complying with 1008.3 shall be permitted to connect elevated play components in water.
Transfer systems complying with 1008.3 shall be permitted to connect elevated play components in _____.
WATER
1008.2.3 Play Areas, Water Play Components - Accessible routes serving water play components shall be permitted to use the exceptions in 1008.2.3.
EXCEPTIONS:
1. Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is submerged, compliance with 302, 403.3, 405.2, 405.3, and 1008.2.6 shall not be required.
2. Transfer systems complying with 1008.3 shall be permitted to connect elevated play components in water.
At ground level, the clear width of play area accessible routes shall be ____ inches minimum.
60 INCHES
1008.2.4.1 Play Areas, Ground Level - At ground level, the clear width of accessible routes shall be 60 inches (1525 mm) minimum.
In play areas less than ____ square feet, the clear width of accessible routes shall be permitted to be ____ inches minimum, if at least one turning space complying with 304.3 is provided where the restricted accessible route exceeds ____ feet in length.
1000 SQUARE FEET, 44 INCHES, 30 FEET
1008.2.4.1 Play Areas, Ground Level - At ground level, the clear width of accessible routes shall be 60 inches (1525 mm) minimum.
EXCEPTIONS:
1. In play areas less than 1000 square feet (93 m), the clear width of accessible routes shall be permitted to be 44 inches (1120 mm) minimum, if at least one turning space complying with 304.3 is provided where the restricted accessible route exceeds 30 feet (9145 mm) in length.
2. The clear width of accessible routes shall be permitted to be 36 inches (915 mm) minimum for a distance of 60 inches (1525 mm) maximum provided that multiple reduced width segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum.
In play areas, the clear width of accessible routes shall be permitted to be ____ inches minimum for a distance of ____ inches maximum provided that multiple reduced width segments are separated by segments that are ____ inches wide minimum and ____ inches long minimum.
36 INCHES, 60 INCHES, 60 INCHES, 60 INCHES
1008.2.4.1 Play Areas, Ground Level - At ground level, the clear width of accessible routes shall be 60 inches (1525 mm) minimum.
EXCEPTIONS:
1. In play areas less than 1000 square feet (93 m), the clear width of accessible routes shall be permitted to be 44 inches (1120 mm) minimum, if at least one turning space complying with 304.3 is provided where the restricted accessible route exceeds 30 feet (9145 mm) in length.
2. The clear width of accessible routes shall be permitted to be 36 inches (915 mm) minimum for a distance of 60 inches (1525 mm) maximum provided that multiple reduced width segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum.
The clear width of accessible routes connecting elevated play components shall be ____ inches minimum.
36 INCHES
1008.2.4.2 Play Areas, Elevated - The clear width of accessible routes connecting elevated play components shall be 36 inches (915 mm) minimum.
The clear width of accessible routes connecting elevated play components shall be permitted to be reduced to ____ inches minimum for a distance of ____ inches maximum provided that reduced width segments are separated by segments that are ____ inches long minimum and ____ inches wide minimum.
32 INCHES, 24 INCHES, 48 INCHES, 36 INCHES
1008.2.4.2 Play Areas, Elevated - The clear width of accessible routes connecting elevated play components shall be 36 inches (915 mm) minimum.
EXCEPTIONS:
1. The clear width of accessible routes connecting elevated play components shall be permitted to be reduced to 32 inches (815 mm) minimum for a distance of 24 inches (610 mm) maximum provided that reduced width segments are separated by segments that are 48 inches (1220 mm) long minimum and 36 inches (915 mm) wide minimum.
2. The clear width of transfer systems connecting elevated play components shall be permitted to be 24 inches (610 mm) minimum.
The clear width of transfer systems connecting elevated play components shall be permitted to be ____ inches minimum.
24 INCHES
1008.2.4.2 Play Areas, Elevated - The clear width of accessible routes connecting elevated play components shall be 36 inches (915 mm) minimum.
EXCEPTIONS:
1. The clear width of accessible routes connecting elevated play components shall be permitted to be reduced to 32 inches (815 mm) minimum for a distance of 24 inches (610 mm) maximum provided that reduced width segments are separated by segments that are 48 inches (1220 mm) long minimum and 36 inches (915 mm) wide minimum.
2. The clear width of transfer systems connecting elevated play components shall be permitted to be 24 inches (610 mm) minimum.
Within play areas, ramps connecting ______ _____ play components and ramps connecting ________ play components shall comply.
GROUND LEVEL, ELEVATED
1008.2.5 Play Areas, Ramps - Within play areas, ramps connecting ground level play components and ramps connecting elevated play components shall comply with 1008.2.5.
Ramp runs connecting ______ _____ play components shall have a running slope not steeper than ____.
GROUND LEVEL, 1:16
1008.2.5.1 Play Areas, Ground Level - Ramp runs connecting ground level play components shall have a running slope not steeper than 1:16.
The rise for any ramp run connecting elevated play components shall be ____ inches maximum.
12 INCHES
1008.2.5.2 Play Areas, Elevated - The rise for any ramp run connecting elevated play components shall be 12 inches (305 mm) maximum.
Where required on ramps serving ____ __________, the handrails shall comply with 505 except as modified by 1008.2.5.3.
PLAY COMPONENTS
1008.2.5.3 Play Areas, Handrails - Where required on ramps serving play components, the handrails shall comply with 505 except as modified by 1008.2.5.3.
Handrails shall not be required on ramps serving play components located within ______ _____ use zones.
GROUND LEVEL
1008.2.5.3 Play Areas, Handrails - Where required on ramps serving play components, the handrails shall comply with 505 except as modified by 1008.2.5.3.
EXCEPTIONS:
1. Handrails shall not be required on ramps located within ground level use zones.
2. Handrail extensions shall not be required.
_________ __________ shall not be required at ramps serving play components.
HANDRAIL EXTENSIONS
1008.2.5.3 Play Areas, Handrails - Where required on ramps serving play components, the handrails shall comply with 505 except as modified by 1008.2.5.3.
EXCEPTIONS:
1. Handrails shall not be required on ramps located within ground level use zones.
2. Handrail extensions shall not be required.
Play area handrail gripping surfaces with a ________ cross section shall have an outside diameter of ____ inch minimum and ____ inches maximum.
CIRCULAR, 0.95 INCH, 1.55 INCHES
1008.2.5.3.1 Play Areas, Handrail Gripping Surfaces - Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum. Where the shape of the gripping surface is non-circular, the handrail shall provide an equivalent gripping surface.
Where the shape of the gripping surface of play area ramps is ____________, the handrail shall provide an _________ gripping surface.
NON-CIRCULAR, EQUIVALENT
1008.2.5.3.1 Play Areas, Handrail Gripping Surfaces - Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum. Where the shape of the gripping surface is non-circular, the handrail shall provide an equivalent gripping surface.
The top of handrail gripping surfaces of play area ramps shall be ____ inches minimum and ____ inches maximum above the ramp surface.
20 INCHES, 28 INCHES
1008.2.5.3.2 Play Areas, Handrail Height - The top of handrail gripping surfaces shall be 20 inches (510 mm) minimum and 28 inches (710 mm) maximum above the ramp surface.
Ground surfaces on __________ ______, _____ _____ __ ______ ______, and _______ ______shall comply with ASTM F 1951 and ASTM F 1292.
ACCESSIBLE ROUTES, CLEAR FLOOR OR GROUND SPACES, TURNING SPACES
1008.2.6 Play Areas, Ground Surfaces - Ground surfaces on accessible routes, clear floor or ground spaces, and turning spaces shall comply with 1008.2.6.
Ground surfaces located under and around play areas shall comply with ___________.
ASTM F 1951
1008.2.6.1 Play Areas, Accessibility - Ground surfaces shall comply with ASTM F 1951 (incorporated by reference, see “Referenced Standards” in Chapter 1). Ground surfaces shall be inspected and maintained regularly and frequently to ensure continued compliance with ASTM F 1951.
Ground surfaces located within play area use zones shall comply with ___________.
ASTM F 1292
1008.2.6.2 Play Areas, Use Zones - Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see “Referenced Standards” in Chapter 1).
________ _________ shall be provided where ________ is intended from wheelchairs or other mobility aids.
TRANSFER PLATFORMS, TRANSFER
1008.3.1 Transfer Systems, Transfer Platforms - Transfer platforms shall be provided where transfer is intended from wheelchairs or other mobility aids. Transfer platforms shall comply with 1008.3.1.
At elevated play components, transfer platforms shall have level surfaces ____ inches deep minimum and ____ inches wide minimum.
14 INCHES DEEP, 24 INCHES WIDE
1008.3.1.1 Transfer Platforms, Size - Transfer platforms shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum.
At elevated play components, the height of transfer platforms shall be ____ inches minimum and ____ inches maximum measured to the top of the surface from the ground or floor surface.
11 INCHES, 18 INCHES
1008.3.1.2 Transfer Platforms, Height - The height of transfer platforms shall be 11 inches (280 mm) minimum and 18 inches (455 mm) maximum measured to the top of the surface from the ground or floor surface.
At elevated play components, a transfer space complying with 305.2 and 305.3 shall be provided adjacent to the ________ ________.
TRANSFER PLATFORM
1008.3.1.3 Transfer Platforms, Transfer Space - A transfer space complying with 305.2 and 305.3 shall be provided adjacent to the transfer platform. The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform. The side of the transfer platform serving the transfer space shall be unobstructed.
The ____ inch long minimum dimension of the transfer space shall be ________ on and ________ to the ___ inch (610 mm) long minimum side of the transfer platform.
48 INCH, CENTERED, PARALLEL 24 INCH
1008.3.1.3 Transfer Platforms, Transfer Space - A transfer space complying with 305.2 and 305.3 shall be provided adjacent to the transfer platform. The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform. The side of the transfer platform serving the transfer space shall be unobstructed.
At elevated play components the side of the transfer platform serving the transfer space shall be ____________.
UNOBSTRUCTED
1008.3.1.3 Transfer Platforms, Transfer Space - A transfer space complying with 305.2 and 305.3 shall be provided adjacent to the transfer platform. The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform. The side of the transfer platform serving the transfer space shall be unobstructed.
At elevated play component transfer platforms, at least ____ means of support for transferring shall be provided.
ONE
1008.3.1.4 Transfer Platforms, Transfer Supports - At least one means of support for transferring shall be provided.
________ _____ shall be provided where movement is intended from transfer platforms to levels with ________ ____ __________ required to be on accessible routes.
TRANSFER STEPS, ELEVATED PLAY COMPONENT
1008.3.2 Transfer Platforms, Transfer Steps - Transfer steps shall be provided where movement is intended from transfer platforms to levels with elevated play components required to be on accessible routes. Transfer steps shall comply with 1008.3.2.
Transfer steps at elevated play components shall have level surfaces ____ inches deep minimum and ____ inches wide minimum.
14 INCHES, 24 INCHES
1008.3.2.1 Transfer Steps, Size - Transfer steps shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum.
Each transfer step at an elevated play component shall be ____ inches high maximum.
8 INCHES
1008.3.2.2 Transfer Steps, Height - Each transfer step shall be 8 inches (205 mm) high maximum.
At elevated play component transfer steps, at least one means of support for ____________ shall be provided.
TRANSFERRING
1008.3.2.3 Transfer Steps, Transfer Supports - At least one means of support for transferring shall be provided.
At least one _______ _____ complying with 304 shall be provided on the same level as play components.
TURNING SPACE
1008.4.1 Play Components, Turning Space - At least one turning space complying with 304 shall be provided on the same level as play components. Where swings are provided, the turning space shall be located immediately adjacent to the swing.
Where ______ are provided, the turning space shall be located immediately _______ to the _____.
SWINGS, ADJACENT, SWING
1008.4.1 Play Components, Turning Space - At least one turning space complying with 304 shall be provided on the same level as play components. Where swings are provided, the turning space shall be located immediately adjacent to the swing.
A ____ inches minimum by ____ inches minimum clear floor or ground space shall be provided at ____ __________ with no change in level other than a ____ slope.
30 INCHES, 48 INCHES, PLAY COMPONENTS, 1:48
1008.4.2 Play Components, Clear Floor or Ground Space - Clear floor or ground space complying with 305.2 and 305.3 shall be provided at play components.
Where play tables are provided, knee clearance ____ inches high minimum, ____ inches deep minimum, and ____ inches wide minimum shall be provided.
24 INCHES HIGH, 17 INCHES DEEP, 30 INCHES WIDE
1008.4.3 Play Components, Play Tables - Where play tables are provided, knee clearance 24 inches (610 mm) high minimum, 17 inches deep (430 mm) minimum, and 30 inches (760 mm) wide minimum shall be provided. The tops of rims, curbs, or other obstructions shall be 31 inches (785 mm) high maximum.
The tops of rims, curbs, or other obstructions at play tables shall be ____ inches high maximum.
31 INCHES
1008.4.3 Play Components, Play Tables - Where play tables are provided, knee clearance 24 inches (610 mm) high minimum, 17 inches deep (430 mm) minimum, and 30 inches (760 mm) wide minimum shall be provided. The tops of rims, curbs, or other obstructions shall be 31 inches (785 mm) high maximum.
Play tables designed and constructed primarily for children ___ years and younger shall not be required to provide ____ clearance where the clear floor or ground space required by 1008.4.2 is arranged for a ________ approach.
5 YEARS, KNEE, PARALLEL
1008.4.3 Play Components, Play Tables - Where play tables are provided, knee clearance 24 inches (610 mm) high minimum, 17 inches deep (430 mm) minimum, and 30 inches (760 mm) wide minimum shall be provided. The tops of rims, curbs, or other obstructions shall be 31 inches (785 mm) high maximum.
EXCEPTION: Play tables designed and constructed primarily for children 5 years and younger shall not be required to provide knee clearance where the clear floor or ground space required by 1008.4.2 is arranged for a parallel approach.
Where play components require ________ to entry points or seats, the entry points or seats shall be ____ inches minimum and ____ inches maximum from the clear floor or ground space.
TRANSFER, 11 INCHES, 24 INCHES
1008.4.4 Play Components, Entry Points and Seats - Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground space.
T / F - Entry points of slides shall not be required to comply distance requirements to clear floor or ground space.
TRUE
1008.4.4 Play Components, Entry Points and Seats - Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground space.
EXCEPTION: Entry points of slides shall not be required to comply with 1008.4.4.
Where play components require transfer to entry points or seats, at least ____ means of support for transferring shall be provided.
ONE
1008.4.5 Play Components, Transfer Supports - Where play components require transfer to entry points or seats, at least one means of support for transferring shall be provided.
Swimming pool, wading pool, and spa lifts shall be located where the water level does not exceed ____ inches.
48 INCHES
1009.2.1 Pool Lifts, Pool Lift Location. Pool lifts shall be located where the water level does not exceed 48 inches (1220 mm).
Where the entire pool depth is greater than ____ inches (1220 mm), compliance with 1009.2.1 shall ___ __ ________.
48 INCHES, NOT BE REQUIRED
1009.2.1 Pool Lifts, Pool Lift Location. Pool lifts shall be located where the water level does not exceed 48 inches (1220 mm).
EXCEPTIONS:
1. Where the entire pool depth is greater than 48 inches (1220 mm), compliance with 1009.2.1 shall not be required.
2. Where multiple pool lift locations are provided, no more than one pool lift shall be required to be located in an area where the water level is 48 inches (1220 mm) maximum.
Where multiple swimming pool, wading pool, and spa lift locations are provided, no more than ___ pool lift shall be required to be located in an area where the water level is ____ inches maximum.
ONE, 48 INCHES
1009.2.1 Pool Lifts, Pool Lift Location. Pool lifts shall be located where the water level does not exceed 48 inches (1220 mm).
EXCEPTIONS:
1. Where the entire pool depth is greater than 48 inches (1220 mm), compliance with 1009.2.1 shall not be required.
2. Where multiple pool lift locations are provided, no more than one pool lift shall be required to be located in an area where the water level is 48 inches (1220 mm) maximum.
In the raised position, the centerline of the seat of a swimming pool, wading pool, and spa lift shall be located over the deck and ____ inches minimum from the edge of the ____.
16 INCHES, POOL
1009.2.2 Pool Lifts, Seat Location - In the raised position, the centerline of the seat shall be located over the deck and 16 inches (405 mm) minimum from the edge of the pool. The deck surface between the centerline of the seat and the pool edge shall have a slope not steeper than 1:48.
The deck surface of a swimming pool, wading pool, and spa lift seat location, between the __________ of the seat and the ____ edge, shall have a slope not steeper than ____.
CENTERLINE, POOL, 1:48
1009.2.2 Pool Lifts, Seat Location - In the raised position, the centerline of the seat shall be located over the deck and 16 inches (405 mm) minimum from the edge of the pool. The deck surface between the centerline of the seat and the pool edge shall have a slope not steeper than 1:48.
Swimming pool, wading pool, and spa lifts shall provide a clear deck space ________ with the seat, on the side of the seat ________ the water.
PARALLEL, OPPOSITE
1009.2.3 Pool Lifts, Clear Deck Space - On the side of the seat opposite the water, a clear deck space shall be provided parallel with the seat. The space shall be 36 inches (915 mm) wide minimum and shall extend forward 48 inches (1220 mm) minimum from a line located 12 inches (305 mm) behind the rear edge of the seat. The clear deck space shall have a slope not steeper than 1:48.
The clear deck space at a swimming pool, wading pool, and spa shall be ____ inches wide minimum and shall extend forward ____ inches minimum from a line located ____ inches behind the rear edge of the seat.
36 INCHES, 48 INCHES, 12 INCHES
1009.2.3 Pool Lifts, Clear Deck Space - On the side of the seat opposite the water, a clear deck space shall be provided parallel with the seat. The space shall be 36 inches (915 mm) wide minimum and shall extend forward 48 inches (1220 mm) minimum from a line located 12 inches (305 mm) behind the rear edge of the seat. The clear deck space shall have a slope not steeper than 1:48.
T / F - The clear deck space at a swimming pool, wading pool, and spa lift shall have a slope not steeper than 1:48.
TRUE
1009.2.3 Pool Lifts, Clear Deck Space - On the side of the seat opposite the water, a clear deck space shall be provided parallel with the seat. The space shall be 36 inches (915 mm) wide minimum and shall extend forward 48 inches (1220 mm) minimum from a line located 12 inches (305 mm) behind the rear edge of the seat. The clear deck space shall have a slope not steeper than 1:48.
The height of the swimming pool, wading pool, and spa lift seat shall be designed to allow a stop at ____ inches minimum to ____ inches maximum measured from the ____ to the top of the seat surface when in the raised (load) position.
16 INCHES, 19 INCHES, DECK
1009.2.4 Pool Lifts, Seat Height - The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the raised (load) position.
The seat of a swimming pool, wading pool, and spa lift shall be ____ inches wide minimum.
16 INCHES
1009.2.5 Pool Lifts, Seat Width - The seat shall be 16 inches (405 mm) wide minimum.
_________ shall be provided on swimming pool and wading pool lifts and shall ____ with the seat.
FOOTRESTS, MOVE
1009.2.6 Pool Lifts, Footrests and Armrests - Footrests shall be provided and shall move with the seat. If provided, the armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position.
If provided, the _______ positioned ________ the water shall be removable or shall fold clear of the seat when the seat is in the ______ position.
ARMREST, OPPOSITE, RAISED
1009.2.6 Pool Lifts, Footrests and Armrests - Footrests shall be provided and shall move with the seat. If provided, the armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position.
T / F - Footrests shall not be required on pool lifts provided in spas.
TRUE
1009.2.6 Pool Lifts, Footrests and Armrests - Footrests shall be provided and shall move with the seat. If provided, the armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position.
EXCEPTION: Footrests shall not be required on pool lifts provided in spas.
The swimming pool, wading pool, and spa lift shall be capable of __________ operation from both the ____ and _____ levels.
UNASSISTED, DECK, WATER
1009.2.7 Pool Lifts, Operation - The lift shall be capable of unassisted operation from both the deck and water levels. Controls and operating mechanisms shall be unobstructed when the lift is in use and shall comply with 309.4.
Controls and operating mechanisms shall be ____________ when the swimming pool, wading pool, and spa lift is in use and shall comply with 309.4.
UNOBSTRUCTED
1009.2.7 Pool Lifts, Operation - The lift shall be capable of unassisted operation from both the deck and water levels. Controls and operating mechanisms shall be unobstructed when the lift is in use and shall comply with 309.4.
Controls and operating mechanisms shall be unobstructed when the swimming pool, wading pool, and spa lift is in use and shall not require _____ ________, ________, or ________ of the _____.
TIGHT GRASPING, PINCHING, TWISTING, WRIST
1009.2.7 Pool Lifts, Operation - The lift shall be capable of unassisted operation from both the deck and water levels. Controls and operating mechanisms shall be unobstructed when the lift is in use and shall comply with 309.4.
The swimming pool, wading pool, and spa lift shall be designed so that the seat will submerge to a water depth of ___ inches minimum below the stationary water level.
18 INCHES
1009.2.8 Pool Lifts, Submerged Depth - The lift shall be designed so that the seat will submerge to a water depth of 18 inches (455 mm) minimum below the stationary water level.
Single person swimming pool, wading pool, and spa lifts shall have a weight capacity of ___ pounds minimum and be capable of sustaining a static load of at least ___ _____ the rated load.
300 POUNDS, 1.5 TIMES
1009.2.9 Pool Lifts, Lifting Capacity - Single person pool lifts shall have a weight capacity of 300 pounds. (136 kg) minimum and be capable of sustaining a static load of at least one and a half times the rated load.
T / F - Where sloped entries are provide to swimming pools, wading pools, and spas, the surface shall be slip resistant.
FALSE
1009.3.1 Sloped Entries - Sloped entries shall comply with Chapter 4 except as modified in 1109.3.1 through 1109.3.3.
EXCEPTION: Where sloped entries are provided, the surfaces shall not be required to be slip resistant.
Swimming pool, wading pool, and spa sloped entries shall extend to a depth of ____ inches minimum and ____ inches maximum below the __________ water level.
24 INCHES, 30 INCHES, STATIONARY
1009.3.2 Sloped Entries, Submerged Depth - Sloped entries shall extend to a depth of 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level. Where landings are required by 405.7, at least one landing shall be located 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level.
Where landings are required by 405.7, at least ____ landing shall be located ____ inches minimum and ____ inches maximum below the __________ water level.
ONE, 24 INCHES, 30 INCHES, STATIONARY
1009.3.2 Sloped Entries, Submerged Depth - Sloped entries shall extend to a depth of 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level. Where landings are required by 405.7, at least one landing shall be located 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level.
T / F - In wading pools, the sloped entry and landings, if provided, shall extend to the deepest part of the wading pool.
TRUE
1009.3.2 Sloped Entries, Submerged Depth - Sloped entries shall extend to a depth of 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level. Where landings are required by 405.7, at least one landing shall be located 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level.
EXCEPTION: In wading pools, the sloped entry and landings, if provided, shall extend to the deepest part of the wading pool.
At least ___ handrails complying with 505 shall be provided on the swimming pool, wading pool, and spa ______ entry.
TWO, SLOPED
1009.3.3 Sloped Entries, Handrails - At least two handrails complying with 505 shall be provided on the sloped entry. The clear width between required handrails shall be 33 inches (840 mm) minimum and 38 inches (965 mm) maximum.
The clear width between required handrails shall be ____ inches minimum and ____ inches maximum.
33 INCHES, 38 INCHES
1009.3.3 Sloped Entries, Handrails - At least two handrails complying with 505 shall be provided on the sloped entry. The clear width between required handrails shall be 33 inches (840 mm) minimum and 38 inches (965 mm) maximum.
Handrail __________ specified by 505.10.1 shall not be required at the ______ landing serving a sloped entry.
EXTENSIONS, BOTTOM
1009.3.3 Sloped Entries, Handrails - At least two handrails complying with 505 shall be provided on the sloped entry. The clear width between required handrails shall be 33 inches (840 mm) minimum and 38 inches (965 mm) maximum.
EXCEPTIONS:
1. Handrail extensions specified by 505.10.1 shall not be required at the bottom landing serving a sloped entry.
2. Where a sloped entry is provided for wave action pools, leisure rivers, sand bottom pools, and other pools where user access is limited to one area, the handrails shall not be required to comply with the clear width requirements of 1009.3.3.
3. Sloped entries in wading pools shall not be required to provide handrails complying with 1009.3.3. If provided, handrails on sloped entries in wading pools shall not be required to comply with 505.
Where a sloped entry is provided for ____ ______ pools, _______ ______, ____ ______ pools, and other pools where user access is limited to ___ area, the handrails shall not be required to comply with the clear width requirements of 33 inches (840 mm) minimum and 38 inches (965 mm) maximum.
WAVE ACTION, LEISURE RIVERS, SAND BOTTOM, ONE
1009.3.3 Sloped Entries, Handrails - At least two handrails complying with 505 shall be provided on the sloped entry. The clear width between required handrails shall be 33 inches (840 mm) minimum and 38 inches (965 mm) maximum.
EXCEPTIONS:
1. Handrail extensions specified by 505.10.1 shall not be required at the bottom landing serving a sloped entry.
2. Where a sloped entry is provided for wave action pools, leisure rivers, sand bottom pools, and other pools where user access is limited to one area, the handrails shall not be required to comply with the clear width requirements of 1009.3.3.
3. Sloped entries in wading pools shall not be required to provide handrails complying with 1009.3.3. If provided, handrails on sloped entries in wading pools shall not be required to comply with 505.
Sloped entries in wading pools shall not be required to provide _________ complying with the clear width of 33 inches (840 mm) minimum and 38 inches (965 mm) maximum.
If provided, handrails on sloped entries in ______ pools shall not be required to comply with 505.
HANDRAILS, WADING
1009.3.3 Sloped Entries, Handrails - At least two handrails complying with 505 shall be provided on the sloped entry. The clear width between required handrails shall be 33 inches (840 mm) minimum and 38 inches (965 mm) maximum.
EXCEPTIONS:
1. Handrail extensions specified by 505.10.1 shall not be required at the bottom landing serving a sloped entry.
2. Where a sloped entry is provided for wave action pools, leisure rivers, sand bottom pools, and other pools where user access is limited to one area, the handrails shall not be required to comply with the clear width requirements of 1009.3.3.
3. Sloped entries in wading pools shall not be required to provide handrails complying with 1009.3.3. If provided, handrails on sloped entries in wading pools shall not be required to comply with 505.
A clear deck space of ____ inches minimum by ____ inches minimum with a slope not steeper than ____ shall be provided at the base of the swimming pool, wading pool, and spa transfer wall.
60 INCHES, 60 INCHES, 1:48
1009.4.1 Transfer Walls, Clear Deck Space - A clear deck space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall. Where one grab bar is provided, the clear deck space shall be centered on the grab bar. Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars.
Where ___ grab bar is provided at a swimming pool, wading pool, and spa transfer wall, the clear deck space shall be centered on the grab bar.
ONE
1009.4.1 Transfer Walls, Clear Deck Space - A clear deck space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall. Where one grab bar is provided, the clear deck space shall be centered on the grab bar. Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars.
Where ___ grab bars are provided at a swimming pool, wading pool, and spa transfer wall, the clear deck space shall be centered on the clearance between the grab bar.
TWO
1009.4.1 Transfer Walls, Clear Deck Space - A clear deck space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall. Where one grab bar is provided, the clear deck space shall be centered on the grab bar. Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars.
The height of the swimming pool, wading pool, and spa transfer wall shall be ____ inches minimum and ____ inches maximum measured from the deck.
16 INCHES, 19 INCHES
1009.4.2 Transfer Walls, Height - The height of the transfer wall shall be 16 inches (405 mm) minimum and 19 inches (485 mm) maximum measured from the deck.
The depth of the swimming pool, wading pool, and spa transfer wall shall be ____ inches minimum and ____ inches maximum.
12 INCHES, 16 INCHES
1009.4.3 Transfer Walls, Wall Depth and Length - The depth of the transfer wall shall be 12 inches (305 mm) minimum and 16 inches (405 mm) maximum. The length of the transfer wall shall be 60 inches (1525 mm) minimum and shall be centered on the clear deck space.
The length of the swimming pool, wading pool, and spa transfer wall shall be ____ inches minimum and shall be ________ on the clear deck space.
60 INCHES, CENTERED
1009.4.3 Transfer Walls, Wall Depth and Length - The depth of the transfer wall shall be 12 inches (305 mm) minimum and 16 inches (405 mm) maximum. The length of the transfer wall shall be 60 inches (1525 mm) minimum and shall be centered on the clear deck space.
Surfaces of swimming pool, wading pool, and spa transfer walls shall not be _____ and shall have _______ edges.
SHARP, ROUNDED
1009.4.4 Transfer Walls, Surface - Surfaces of transfer walls shall not be sharp and shall have rounded edges.
T / F - At least one grab bar complying with 609 shall be provided on the swimming pool, wading pool, and spa transfer wall.
TRUE
1009.4.5 Transfer Walls, Grab Bars - At least one grab bar complying with 609 shall be provided on the transfer wall. Grab bars shall be perpendicular to the pool wall and shall extend the full depth of the transfer wall. The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls. Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar. Where two grab bars are provided, clearance between grab bars shall be 24 inches (610 mm) minimum.
EXCEPTION: Grab bars on transfer walls shall not be required to comply with 609.4.
Grab bars shall be _____________ to the pool wall and shall extend the full _____ of the swimming pool, wading pool, and spa transfer wall.
PERPENDICULAR, DEPTH
1009.4.5 Transfer Walls, Grab Bars - At least one grab bar complying with 609 shall be provided on the transfer wall. Grab bars shall be perpendicular to the pool wall and shall extend the full depth of the transfer wall. The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls. Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar. Where two grab bars are provided, clearance between grab bars shall be 24 inches (610 mm) minimum.
EXCEPTION: Grab bars on transfer walls shall not be required to comply with 609.4.
The top of the gripping surface shall be ____ inches minimum and ____ inches maximum above swimming pool, wading pool, and spa transfer walls.
4 INCHES, 6 INCHES
1009.4.5 Transfer Walls, Grab Bars - At least one grab bar complying with 609 shall be provided on the transfer wall. Grab bars shall be perpendicular to the pool wall and shall extend the full depth of the transfer wall. The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls. Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar. Where two grab bars are provided, clearance between grab bars shall be 24 inches (610 mm) minimum.
EXCEPTION: Grab bars on transfer walls shall not be required to comply with 609.4.
Where one grab bar is provided, clearance shall be ____ inches minimum on ____ sides of the grab bar.
24 INCHES, BOTH
1009.4.5 Transfer Walls, Grab Bars - At least one grab bar complying with 609 shall be provided on the transfer wall. Grab bars shall be perpendicular to the pool wall and shall extend the full depth of the transfer wall. The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls. Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar. Where two grab bars are provided, clearance between grab bars shall be 24 inches (610 mm) minimum.
EXCEPTION: Grab bars on transfer walls shall not be required to comply with 609.4.
Where two grab bars are provided, clearance _______ grab bars shall be ____ inches minimum.
BETWEEN, 24 INCHES
1009.4.5 Transfer Walls, Grab Bars - At least one grab bar complying with 609 shall be provided on the transfer wall. Grab bars shall be perpendicular to the pool wall and shall extend the full depth of the transfer wall. The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls. Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar. Where two grab bars are provided, clearance between grab bars shall be 24 inches (610 mm) minimum.
EXCEPTION: Grab bars on transfer walls shall not be required to comply with 609.4.
T / F - Grab bars on swimming pool, wading pool, and spa transfer walls shall comply with 609.4.
FALSE
1009.4.5 Transfer Walls, Grab Bars - At least one grab bar complying with 609 shall be provided on the transfer wall. Grab bars shall be perpendicular to the pool wall and shall extend the full depth of the transfer wall. The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls. Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar. Where two grab bars are provided, clearance between grab bars shall be 24 inches (610 mm) minimum.
EXCEPTION: Grab bars on transfer walls shall not be required to comply with 609.4.
A transfer ________ shall be provided at the head of each swimming pool, wading pool, and spa transfer system.
PLATFORM
1009.5.1 Transfer Systems, Transfer Platform - A transfer platform shall be provided at the head of each transfer system. Transfer platforms shall provide 19 inches (485 mm) minimum clear depth and 24 inches (610 mm) minimum clear width.
Transfer platforms at swimming pool, wading pool, and spa transfer systems shall provide ____ inches minimum clear depth and ____ inches minimum clear width.
19 INCHES, 24 INCHES
1009.5.1 Transfer Systems, Transfer Platform - A transfer platform shall be provided at the head of each transfer system. Transfer platforms shall provide 19 inches (485 mm) minimum clear depth and 24 inches (610 mm) minimum clear width.
The transfer space at a swimming pool, wading pool, and spa transfer system shall be ____ inches minimum by ____ inches minimum with a slope not steeper than ____ shall be provided at the base of the transfer platform surface and shall be centered along a ____ inch minimum side of the transfer platform.
60 INCHES, 60 INCHES, 1:48, 24 INCHES
1009.5.2 Transfer Systems, Transfer Space - A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall be centered along a 24 inch (610 mm) minimum side of the transfer platform. The side of the transfer platform serving the transfer space shall be unobstructed.
The side of a swimming pool, wading pool, and spa transfer platform serving the transfer space shall be ____________.
UNOBSTRUCTED
1009.5.2 Transfer Systems, Transfer Space - A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall be centered along a 24 inch (610 mm) minimum side of the transfer platform. The side of the transfer platform serving the transfer space shall be unobstructed.
The height of the transfer wall of a swimming pool, wading pool, and spa transfer system shall be ____ inches minimum and ____ inches maximum measured from the deck.
16 INCHES, 19 INCHES
1009.5.3 Transfer Systems, Height - The height of the transfer platform shall comply with 1009.4.2.
The transfer step height of a swimming pool, wading pool, and spa transfer system shall be ___ inches maximum.
8 INCHES
1009.5.4 Transfer Systems, Transfer Steps - Transfer step height shall be 8 inches (205 mm) maximum. The surface of the bottom tread shall extend to a water depth of 18 inches (455 mm) minimum below the stationary water level.
The surface of the bottom tread of a swimming pool, wading pool, and spa transfer system shall extend to a water depth of ____ inches minimum below the stationary water level.
18 INCHES
1009.5.4 Transfer Systems, Transfer Steps - Transfer step height shall be 8 inches (205 mm) maximum. The surface of the bottom tread shall extend to a water depth of 18 inches (455 mm) minimum below the stationary water level.
The surface of the swimming pool, wading pool, and spa transfer system shall not be _____ and shall have _______ edges.
SHARP, ROUNDED
1009.5.5 Transfer Systems, Surface - The surface of the transfer system shall not be sharp and shall have rounded edges.
Each transfer step of a swimming pool, wading pool and spa transfer system shall have a tread clear depth of ___ inches minimum and ___ inches maximum and shall have a tread clear width of ___ inches minimum.
14 INCHES, 17 INCHES, 24 INCHES
1009.5.6 Transfer Systems, Size - Each transfer step shall have a tread clear depth of 14 inches (355 mm) minimum and 17 inches (430 mm) maximum and shall have a tread clear width of 24 inches (610 mm) minimum.
At least one grab bar on each transfer ____ and the transfer ________ or a __________ grab bar serving each transfer step and the transfer platform shall be provided.
STEP, PLATFORM, CONTINUOUS
1009.5.7 Transfer Systems, Grab Bars - At least one grab bar on each transfer step and the transfer platform or a continuous grab bar serving each transfer step and the transfer platform shall be provided. Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above each step and transfer platform. Where a continuous grab bar is provided, the top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above the step nosing and transfer platform. Grab bars shall comply with 609 and be located on at least one side of the transfer system. The grab bar located at the transfer platform shall not obstruct transfer.
Where a grab bar is provided on each step of a swimming pool wading pool and spa transfer system, the tops of gripping surfaces shall be __ inches (100 mm) minimum and __ inches (150 mm) maximum above each step and transfer platform.
4 INCHES, 6 INCHES
1009.5.7 Transfer Systems, Grab Bars - At least one grab bar on each transfer step and the transfer platform or a continuous grab bar serving each transfer step and the transfer platform shall be provided. Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above each step and transfer platform. Where a continuous grab bar is provided, the top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above the step nosing and transfer platform. Grab bars shall comply with 609 and be located on at least one side of the transfer system. The grab bar located at the transfer platform shall not obstruct transfer.
Where a continuous grab bar is provided at swimming pool, wading pool, and spa transfer systems, the top of the gripping surface shall be __ inches minimum and __ inches maximum above the step nosing and transfer platform.
4 INCHES, 6 INCHES
1009.5.7 Transfer Systems, Grab Bars - At least one grab bar on each transfer step and the transfer platform or a continuous grab bar serving each transfer step and the transfer platform shall be provided. Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above each step and transfer platform. Where a continuous grab bar is provided, the top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above the step nosing and transfer platform. Grab bars shall comply with 609 and be located on at least one side of the transfer system. The grab bar located at the transfer platform shall not obstruct transfer.
Grab bars at swimming pool, wading pool, and spa transfer systems shall comply with 609 - Grab Bars, and be located on __ _____ ___ ____ of the transfer system.
AT LEAST ONE SIDE
1009.5.7 Transfer Systems, Grab Bars - At least one grab bar on each transfer step and the transfer platform or a continuous grab bar serving each transfer step and the transfer platform shall be provided. Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above each step and transfer platform. Where a continuous grab bar is provided, the top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above the step nosing and transfer platform. Grab bars shall comply with 609 and be located on at least one side of the transfer system. The grab bar located at the transfer platform shall not obstruct transfer.
T / F - Grab bars at swimming pools, wading pools, and spas are required to comply with mounting heights of 609.4.
FALSE
1009.5.7 Transfer Systems, Grab Bars - At least one grab bar on each transfer step and the transfer platform or a continuous grab bar serving each transfer step and the transfer platform shall be provided. Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above each step and transfer platform. Where a continuous grab bar is provided, the top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above the step nosing and transfer platform. Grab bars shall comply with 609 and be located on at least one side of the transfer system. The grab bar located at the transfer platform shall not obstruct transfer.
EXCEPTION: Grab bars on transfer systems shall not be required to comply with 609.4.
T / F - When pool risers heights are uniform, the minimum height is 4 inches (100 mm) and the maximum height is 7 inches (180 mm).
FALSE
1009.6.1 Pool Stairs. Pool stairs shall comply with 504.
EXCEPTION: Pool step riser heights shall not be required to be 4 inches (100 mm) high minimum and 7 inches (180 mm) high maximum provided that riser heights are uniform.
The width between handrails shall be ___ inches minimum and ___ inches maximum.
20 INCHES, 24 INCHES
1009.6.2 Pool Stairs, Handrails - The width between handrails shall be 20 inches (510 mm) minimum and 24 inches (610 mm) maximum. Handrail extensions required by 505.10.3 shall not be required on pool stairs.
T / F - Handrail extensions are required on pool stairs.
FALSE
1009.6.2 Pool Stairs, Handrails - The width between handrails shall be 20 inches (510 mm) minimum and 24 inches (610 mm) maximum. Handrail extensions required by 505.10.3 shall not be required on pool stairs.
A circular turning space ___ inches diameter minimum with slopes not steeper than ____ shall be provided at shooting facilities with firing positions.
60 INCHES, 1:48
1010.1 Shooting Facilities with Firing Positions, Turning Space - A circular turning space 60 inches (1525 mm) diameter minimum with slopes not steeper than 1:48 shall be provided at shooting facilities with firing positions.
