Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

A+ Certification (2022) > Chapter 10 Quiz > Flashcards

Chapter 10 Quiz Flashcards

1
Q

Henry wants to build a computer that will allow him to run a hypervisor program.

What does Henry not need on his computer?

A. Maximum amount of RAM motherboard can accept.
B. High-end video card.
C. High-end processor with multiple cores.
D. Hard drives with large storage capacity.

A

B. High-end video card.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

The laser printer in your accounting department is printing faded prints that are getting lighter over time.
What is the MOST likely reason for the faded prints?
A. The paper pickup rollers are worn.
B. The printer is low on toner.
C. The fuser is not reaching the correct temperature.
D. The printer has foreign matter inside the printer.

A

B. The printer is low on toner.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

While servicing a laser printer, the technician notices that paper is jamming immediately after being pulled from the paper Tray.
What is the MOST likely cause of paper jams?
A. Image drums.
B. Paper feed rollers.
C. Transfer roller.
D. Fuser unit.

A

B. Paper feed rollers.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

A user contacted the help desk to report that the laser printer is his department is wrinkling the paper when printed. The user checked the paper is the supply tray, and it is smooth and unwrinkled.
Which of the following is the MOST likely reason for the wrinkle paper? (Select TWO).
A. The paper does not meet the requirements for the printer.
B. The user is selecting the wrong driver for the printer.
C. The paper is creased before it is installed in the printer.
D. The pages being printed are using too much toner.
E. The paper is damp when when run through the printer.
F. The printer does not have enough free memory.

A

A. The paper does not meet the requirements for the printer.
E. The paper is damp when when run through the printer.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

You are troubleshooting an Inkjet printer that prints areas on the page with random voids and missing colors.
Which of the following will BEST help resolve the problem. (Select TWO)
A. Printhead wires not firing.
B. Head cleaning utility.
C. Low toner level
D.Printer Calibration.
E. Printhead gap setting.
F. Defective ribbon.

A

B. Head cleaning utility.
D.Printer Calibration.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Mary’s company has asked her to research new computers. The company wants to provide workers with minimal computers that have an operating system and a browser that will allow the workers to connect to a server. The server will do most of the necessary processing.
What kind of COMPUTER should Mary recommend?
A. Thick Client.
B. Zero Client.
C. Virtual Client.
D. Thin Client.

A

D. Thin Client.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Mary’s company has asked her to research new computers. The company wants to provide workers with minimal computers that have an operating system and a browser that will allow the workers to connect to a server. The server will do most of the necessary processing.
What kind of COMPUTER should Mary recommend?
A. Thick Client.
B. Zero Client.
C. Virtual Client.
D. Thin Client.

A

D. Thin Client.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Which of the following is a cloud computing element that gives a service provider the ability to dynamically allocate shared physical resources to multiple customers based on each customer’s usage demand?
A. On-demand.
B. Resource pooling.
C. Measured Service.
D. Rapid Elasticity.

A

B. Resource pooling.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Which of the following creates an environment that behaves in a hardware-like manner to run software meant for other hardware?
A. Emulator.
B. Virtual desktop.
C. Zero client.
D. Virtualization.

A

A. Emulator.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What step in the laser printing process is responsible for conditioning the imaging drum in preparation for receiving an electrical charge?
A. Charging.
B. Transferring.
C. Cleaning.
D. Fusing

A

C. Cleaning.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Which of the following are advantages of implementing cloud computing over services hosted internally? )Select THREE)
A. Rapid elasticity.
B. On-demand services.
C. On-site servers.
D. Extensive technical configuration.
E. Metered services.
F. No internet connection required.

A

A. Rapid elasticity.
B. On-demand services.
E. Metered services.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

A help desk technician needs to run virtual machines on her laptop computer for several upcoming training sessions.
Which of the following must be completed before she can use virtualization on her laptop?
A. Add additional RAM to the laptop computer.
B. Enable virtualization support in the laptop’s UEFI.
C. Download and flash the laptop computer’s UEFI.
D. Upgrade the Windows operating system.

A

B. Enable virtualization support in the laptop’s UEFI.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

A small bank with several regional branches is searching for a solution to consolidate its business services into a single site with centralized management. The service should provide secure resources for use by the bank, and these resources must be isolated from any other organization using the same service provider.
Which of the following will best meet the needs of the bank?
A. Private Cloud.
B. Public Cloud.
C. Community Cloud.
D. Hybrid Cloud.

A

A. Private Cloud.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

A customer states that when she removes the printed pages from her laser printer output tray, the black ink smears all over her fingers.
Which of the following is the most likely problem?
A. Fuser Unit.
B. Inked Ribbon.
C. Primary Corona.
D. Erasure Lamps.
E. Cleaning Blade.

A

A. Fuser Unit.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Which of the following can provide a user with a cloud-based application that is integrated with a cloud-based virtual storage service and can be accessed through a web browser?
A. Hybrid.
B. Community.
C. SaaS.
D. IaaS.

A

C. SaaS.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Which of the following components provides the physical network connectivity for a virtual machine, managed by type 2 hypervisor, to connect to an Ethernet switch via a UTP patch cable?
A. Host computer’s physical network interface.
B. This type of connection is not possible using a VM.
C. Virtual machine’s physical network interface.
D. Host computer’s virtual network interface.

A

A. Host computer’s physical network interface.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Which of the following is a centrally hosted and managed desktop environment with the capability of spanning multiple offices across various countries in which each user’s desktop instance is dynamically provisioned?
A. VDI.
B. SaaS.
C. IaaS.
D. VPN.

A

A. VDI.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

A customer is looking to replace three aging network servers that are not able to keep up with the growing demand of the company’s user. The customer would also like to add three additional servers to provide on-site DNS, Internet, and file services. A technician is recommending a bare metal hypervisor as the best solution for this customer.
Which of the following describes the recommended solution?
A. Type 2 hypervisor installed on a windows or Linux host OS.
B. Type 1 hypervisor installed directly on server hardware.
C. Hosted hypervisor installed as an application.
D. Type 2 hypervisor installed directly on server hardware.

A

B. Type 1 hypervisor installed directly on server hardware.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

A company needs a way to convert 10 years of shipping records currently on paper into files that can be saved to its private cloud storage.

Which of the following will be the best choice to accomplish this goal with the least amount of employee effort?

A. Use a dedicated, network-attached laser with a Gigabit Ethernet connection.

B. Use a dedicated flatbed scanner that is connected a workstation via USB 3.0.

C. Use the flatbed scanner on a multifunction device connected to a workstation’s USB port.

D. Use a dedicated ADF scanner connected to either a workstation or the LAN.

A

D. Use a dedicated ADF scanner connected to either a workstation or the LAN.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

A client is asking for a printing solution that will print three sheets of paper with identical information on each page with a single pass of the printer. Furthermore, the client requests that the solution take the least amount of time and effort to maintain.
Which of the following printer types should be recommended?
A. Laser.
B. Inkjet.
C. Impact.
D. Thermal Transfer.

A

C. Impact.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

The accounting department has implemented thin clients and VDI. One of the users is complaining that each time she powers on her thin client, she has access only to a web browser.
Which of the following is the most likely reason for this behavior? (Select TWO).
A. The user has been assigned a persistent VDI account.
B. The user has entered incorrect credentials to the VDI server.
C. The user has been assigned a nonpersistent VDI account.
D. The user’s this client does not have an operating system configured.
E. The user has not signed in to the VDI server with her user account and password.

A

B. The user has entered incorrect credentials to the VDI server.
E. The user has not signed in to the VDI server with her user account and password.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

One of your sales employees is taking a trip to several conventions over the next several weeks and will need to have access to a printer at each of the locations. Each of the convention centers will be providing hassle-free printing for all Apple computer and IOS mobile device users.
Which of the following technologies will most likely be used to provide print services?
A. SaaS.
B. Printui.
C. Airprint.
D. Hybrid Cloud.

A

C. Airprint.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

A company is in the middle of an operating system update windows 10 from windows XP, windows 7, and windows 8.x. The diverse nature of the update has made it imperative that the help desk techs have the ability to run several concurrent VMs. A few of the techs are experiencing frequent and extended periods of 100% CPU usage on their ability to assist users in a timely manner

A. Dynamic allocation of RAM is disabled
B. One or more VHDs are running out of free disk space
C. Insufficient number of physical processor cores
D. Disable hardware-assisted virtualization

A

C. Insufficient number of physical processor cores

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

A user is experiencing garbled print on each page printed from her printer (pick 2)

A. ink cartridge has clogged nozzles
B. Printer paper does not meet specifications
C. Print drivers are corrupt or need to be updated
D. Printer needs to be calibrated
E. An application on the computer is sending garbled print
F. Printer needs to be cleaned

A

C. Print drivers are corrupt or need to be updated

E. An application on the computer is sending garbled print

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

A software developer is testing an application on a Windows 10 desktop computer and needs to perform testing of this same application on Windows 7, Windows 8.1, and Linux operating systems. Due to company policy, the developer must use her existing computer and must be disconnected from the company network while performing these tests.

Which of the following will best meet these requirements while providing the developer the same level of usability she is accustomed to?

A. Boot a Type 1 hypervisor from a flash drive and create the Windows VMs and a Linux VM.

B. Install a Type 1 hypervisor and create a Windows 10 VM and the remaining VMs.

C. Create a multi-boot system using Windows 10, Windos 8.1, and Window 7 and then create a Linux VM.

D. Install a Type 2 hypervisor and create the Windows VMs and a Linux VM.

A

D. Install a Type 2 hypervisor and create the Windows VMs and a Linux VM.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

Which of the following technologies provides a method for personalizing network-connected laptop and desktop computers with only the apps each individuals users needs without complicated customization? (select TWO)

A. Measured Service
B. Application virtualization
C. Off-site email application
D. Cloud-based applications
E Metered service

A

B. Application virtualization
D. Cloud-based applications

26
Q

A company purchased a high-quality color laser printer to print color Brochures and sales proposals. The printer is connected to a marketing PC via USB and is configured as a shared local printer for use by the sales and marketing teams. The manager is concerned about the cost of consumables for the printer and does not want users to unintentionally print to the printer.What can be done to ensure that only authorized users can send print jobs to the printer?

A. Disable print spooling on the marketing PC
B. Disable the local share on the marketing PC
C. Set security permissions for the marketing PC signed-in user
D. Enabled user authentication on the printer share

A

D. Enabled user authentication on the printer share

27
Q

A technician is performing routine preventative maintenance on a laser printer and has been asked by the client to check the printer’s paper feeder for issues.

Which of the following printer parts should the technician check first for problems related to paper feeding? (Select TWO.)

A. Transfer belt
B. Separation pad
C. Tractor feed
D. print head
E. toner cartridge
F. pickup rollers

A

B. Separation pad
F. pickup rollers

28
Q

what type of computer is recommended when you want to allow the server to do most of the computing but would like to connect to the server via browser
A. virtual client
B. Thin client
C. zero client
D. thick client

A

B. Thin client

29
Q

A technician wants to use a hosted virtual machine to provide shared files and folders on the company LAN
A. isolate the virtual NIC on its own network subnet
B. Connect the virtual NIC to the host physical NIC
C. disable the physical NIC and enable the virtual NIC
D. disable the virtual NIC and enable the physical NIC

A

B. Connect the virtual NIC to the host physical NIC

30
Q

You were hired by a design firm the uses mac equipment exclusively. You prefer to use your windows laptop and would like to print to the printers already in use. When you open the list of shared printers, nothing is shown
A. stop and restart the print spooler on your laptop
B.set the printer you prefer to use as default
C. download and install Bonjour Print Services
D. install the printer using windows update

A

C. download and install Bonjour Print Services

31
Q

Which of the following could be a major concern for implementing cloud computing for business-critical services?

A. Being charged for computing services that go unused
B. An intermittent or unavailable Internet connection
C. Incompatible software, hardware, or Operating systems
D. A cloud provider’s inability to scale up or down

A

B. An intermittent or unavailable Internet connection

32
Q

Which of the following terms describes the software layer that is responsible for creating and running a VM on a host?

A. Virtual machine
B. physical Machine
C. Intel VT
D. Hypervisor
E. Virtual hard disks

A

D. Hypervisor

33
Q

A technician is troubleshooting a printer connected to a computer via USB. The printer will print using the controls at the printer but fails to print from the computer. Which of the following steps should be taken next?

A. Verify the USB cable is attached
B. check for low memory errors on the printer
C. Make sure the printing paper is installed
D. verify the printer is powered on

A

A. Verify the USB cable is attached

34
Q

A technician is installing a hypervisor on a host system with a single physical NIC that runs a high-bandwidth network application. The host NIC is running at optimum bandwidth and cannot support additional network traffic. The technician will be configuring eight networked VMs that will be interconnected and on their own dedicated virtual subnet separate from the existing physical LAN subnet. When networking the VMs, what will the technician need to do to guarantee that the host network’s performance is not affected without adding complexity or additional cost to the host configuration?

A. Isolate all VM virtual NICs from the physical NIC
B. Connect each VM to a different physical switch port on he LAN subnet
C. Connect only the VMs that are running on he hos’s physical NIC
D. Install one new physical NIC for each VM

A

A. Isolate all VM virtual NICs from the physical NIC

35
Q

Which of the following is considered a security benefit when utilizing virtualization

A. Allowing multiple applications to be installed on physical machines
B. Consolidation multiple OSs onto the same physical hardware
C. Simulating a single operating system on multiple hardware platforms
D. Isolating operating system when running multiple concurrent VMs

A

D. Isolating operating system when running multiple concurrent VMs

36
Q

A technician has connected a USB printer to a workstation and shared the printer on the on the local workstation for the other users on the network to utilize. The technician successfully printed a test print from the printer’s console and the workstation that and the workstation that the printer is physically connected to. After leaving the customer’s site, the technician received a call from the customer stating no one other than the local user can print to the printer. Each time they attempt to print, they receive an “Access Denied” message. Which of the following is the most likely reason to the other users cannot print?

A. The printer is malfunctioning and requires service
B. the other users lack sufficient permissions for the shared printer
C. the other users need to have the print drivers updated for the printer
D. the USB cable is defective and needs to be replaced

A

B. the other users lack sufficient permissions for the shared printer

37
Q

A laser printer is displaying a message indicating a maintenance kit is due for replacement. Which of the following will be a part of the replacement process?

A.replace he print head
B. reset the page counter
C. replace the print ribbon
D. clean the heating element

A

B. reset the page counter

38
Q

A customer has contacted you to help him alleviate the large amount of time and effort that goes into adding and removing users who require access to a business productivity suite. The suite of applications includes word processing, spreadsheet, presentation, and email. Each time an employee is hired, a technician spends over an hour preparing a computer for the user. Likewise, when an employee leaves the company, a technician spends an hour decommissioning the computer. What aspect of cloud computing will be most beneficial in reducing a technician’s time and effort while still giving the technician the ability to create and delete user account?

A. Meter service
B. On-demand
C. Measure service
D. Hybrid cloud

A

B. On-demand

39
Q

You connected a printer directly to the network using the printer’s integrated NIC. The printer was configured with an IP address for users on the local subnet to utilize.

Which of the following best describes the printing method used by this printer?

A. Cloud printing
B remote printing
C. Local Printing
D. Shared local printing

A

B remote printing

40
Q

Which of the following aspects of cloud computing allows a service provider limit a customer’s use of a particular resource based on a service agreement between the provider and the customer?

A. Metered service
B. On-demand
C. Rapid elasticity
D. Measured service

A

D. Measured service

41
Q

A technician is using a network-attached desktop computer with a type 2 hypervisor to run two VM’s. One of the VMs is infected with multiple worms and other forms of known malware. The second VM is a clean installation of Windows. The technician has been tasked with logging the impact on the clean Windows VM when the infected VM attempts to infiltrate the clean VM through the network.
What should the technician do to best protect the company LAN while preforming these tests?

A. place both VMs on virtual NICs that are isolated from the company LAN.
B. Disable the virtual network Interface controller in ecah VM OS
C. Encrypt each VM and the host OS using disk-based encryption
D. Enable the software firewalls on each VM OS and on the host OS

A

A. place both VMs on virtual NICs that are isolated from the company LAN.

42
Q

Which of the following technologies can provide an application to remote users without the need to install application on the users’ systems?
a. Virtual network interface
b. Application virtualization
c. Synchronization app
d. Infrastructure mode

A

b. Application virtualization

43
Q

A company is hiring several remote employees who will be working primarily from their homes but will need to come into the office once a month. The company is providing the workers with laptop computers and wants a way for them to access their email account whether they are at home, on the road, or in the office.
Which of the following will be the best solution?
A. off-site email application
B. Internal shared resource
C. Virtual desktop infrastructure
D. Private cloud model

A

A. off-site email application

44
Q

small company has hired you to take over its IT needs. The company currently has seven on-site employees and 12 remote employees working from their homes and is looking to hire an additional 20 employees in the next six to eight months. The owners of the company are asking you to obtain a business service that will meet the needs of the current staff as well as scale up when the company grows. The service must provide provide adequate and scalable computing power and storage.
Which clod service model should you implement?
A. XaaS
B. PaaS
C. SaaS
D. IaaS

A

D. IaaS

45
Q

Which of the following is a cloud computing service model that relies most heavily on the cloud vendor to manage and maintain its services?
A. PaaS
B. Traditional
C. IaaS
D. SaaS

A

D. SaaS

46
Q

One of the users in your company is asking if he can install an app on his company-provided mobile device. The installation of apps by users is blocked on the company’s mobile devices, but you have tested and confirmed this app would be useful for everyone.

Which of the following will allow users to request a minimal version of the app that downloads only what is required to run?

A. Rapid elasticity
B. Resource pooling
C. Off-site email application
D. Application streaming

A

D. Application streaming

47
Q

You have been tasked with preforming routine maintenance on an inkjet printer. After printing test page, you notice the missing lines of print in various areas throughout the page.
which of the following should you do to resolve this issue? (Select TWO)
A. Manually clean the print nozzles
B. Replace the toner cartridge
C. Change the image drum
D. Run the head cleaning utility
E. Clean the dot matrix print head
F. Replace the fuser assembly

A

A. Manually clean the print nozzles
D. Run the head cleaning utility

48
Q

A customer is experiencing intervals during the day when the file server on her local network cannot keep up with the demands of the users. During these times, some users have to wait for files to open or save, and some users get errors stating their application has timed out.

Which of the following could be a possible solution to this ongoing issue? (Select TWO.)

A. Contact the cloud service provider to increase resource pooling
B. add additional file servers to the local network to handle the demand
C. ask half of the users to stop using the application during the problem time
D. Implement an off-site cloud-based email application
E. Implement a cloud-based model with rapid elasticity

A

B. add additional file servers to the local network to handle the demand

E. Implement a cloud-based model with rapid elasticity

49
Q

Kendra, a user, would like to share her serial printer that has not networking connectivity with the other users in her small office.
which of the following would be the best choice for providing this functionality with the least effort and cost to the user?
A. install an integrated printer
B. enable print sharing on the computer
c. enable print sharing on the Printer
D. update the current print drives

A

B. enable print sharing on the computer

50
Q

A technician is troubleshooting a Windows 10 x64 desktop system with a Type 2 hypervisor that is hosting four VMs that must be run simultaneously. The technician suspects the sluggish performance is due to insufficient physical RAM in the host computer and has disabled dynamic RAM allocation in the hypervisor.

Assuming each operating system installed requires 2GB of RAM, what is the minimum amount of physical RAM that will need to be installed in the host system to meet the requirements of this scenario?

A. 2048MB
B. 8192MB
C. 12288MB
D. 4096MB
E. 10240MB

A

E. 10240MB

51
Q

The receptionist’s directly connected laser printer is printing blank sheets. The technician assigned to the trouble ticket has replaced the toner. However, blank pages continue to print from the receptionist’s PC.
What steps should be performed next?
A. Redirect the print to the primary LPT port
B. Print a test print from the printer’s console
C. Remove the fuser unit and clean the fuser rollers
D. Flip the paper over in the paper tray

A

B. Print a test print from the printer’s console

52
Q

You are installing several VMs on your desktop computer and need to determine whether you system can support running all the VMs at the same time. Your host OS is Windows 10 Pro, and your system has 16GB of physical RAM installed.
What is the best approach in making this determination, assuming dynamic allocation of RAM is disabled?

A. multiply 2GB by the number of guest VMs you want to run at the same time and subtract the RAM required by your host OS

B. Add up to the required RAM for each of the guest VM OS you want to run at the same time and add to RAM required by your host OS

C. add up the minimum required RAM for each of the guest VM operating systems you will run simultaneously and subtract the RAM required by the host OS

D. add up the maximum supported RAM for a 64-bit version of each VM operating system you want to run simultaneously

A

B. Add up to the required RAM for each of the guest VM OS you want to run at the same time and add to RAM required by your host OS

53
Q

The help desk received a call from a user who cannot get any print jobs to print on the locally shared printer. While questioning the user, the technician determines that no users can print to the printer, and the printer indicates it is “Offline.” The technician instructs the user on how to place the printer in the “Online” mode, but print jobs are still not printing on the printer.

Which of the following is the next step to take to resolve this issue?

A. Replace the printer cable
B. Replace the printer toner cartridge
C. Power cycle the printer
D. delete and re-create the printer share

A

C. Power cycle the printer

54
Q

You are on a committee tasked with researching and recommending a service that will allow employees the opportunity to save files from their mobile phones, laptops, and workstation computers to cloud file storage devices.
what will need to be researched and considered in order to make a comprehensive recommendation?
A. virtualization application streaming
B. Type 1 hypervisor
C. Synchronization apps
D. Type 2 hypervisor application
E. off-site email applications

A

C. Synchronization apps

55
Q

What is the correct order for the steps of laser printing?
A. Charging, Processing, Developing, Exposing, Transferring, Cleaning, fusing

B. processing, developing, charging, exposing, fusing, transferring, cleaning

C. Processing, Charging, Developing, Exposing, Transferring, Fusing, Cleaning

D. Charging, Processing, Exposing, Developing, Transferring, Fusing, Cleaning

E. Processing, Charging, Exposing, Developing, Transferring, Fusing, Cleaning

A

E. Processing, Charging, Exposing, Developing, Transferring, Fusing, Cleaning

56
Q

A Windows computer is shared between several users, each with his own local user account. Each user has his own dedicated, uniquely configured VM stored in a public folder on the computer.
What steps should be taken to secure the VMs so no user can copy or delete another user’s VM files? (select 2)
A. install anti-malware software on each VM OS
B. Secure the VM files with permissions
C. Apply encryption to the VM files
D. install anti-malware software on the host OS
E.configure BIOS/UEFI passwords on the host computer
F. connect each VM to separate, dedicated virtual NIC

A

B. Secure the VM files with permissions
C. Apply encryption to the VM files

57
Q

A new printer has been added in your office and connected to a WAP for use by all users in the company.
What best describes the method of connectivity for the new printer?
A. Wireless infrastructure mode
B.wireless Bluetooth
C. wireless ad hoc mode
D. wired ethernet

A

A. Wireless infrastructure mode

58
Q

A user is unable to install virtualization software on a Windows 8.1 computer. The user verified the host has sufficient RAM, plenty of available free disk space, and a multicore processor.

Which of the following is the most likely cause for this behavior?

A. the user does not have a valid product license key
B. the system is incompatible with Type 1 hypervisor
C. The motherboard does not support hardware-assisted virtualization
D. window 8.1 does not support Type 2 hypervisor

A

C. The motherboard does not support hardware-assisted virtualization

59
Q

The administrative assistant of the company’s CEO is asking about a printer for her use only. It seems the shared department printer is overused, making the assistant wait to print the CEO’s last minute documents.
What will best meet the administrative assistant’s request?(select 2)
A. remote printer
B. Bluetooth printer
C. Local printer
D. wireless printer
E. network printer
F. cloud printing

A

B. Bluetooth printer
C. Local printer

60
Q

Molly, a technician, has been asked with researching an emulator for the software developers to test cross-platform applications on various PCs and a variety of mobile devices.
what will be a required step in selecting an emulator?(select 2)
A. Verify the system requirements of the hypervisor
B. Verify the hypervisor software supports the emulator needed for testing
C. verify the emulator supports virtual RAM
D. verify the emulator supports virtual processor
E. verify the emulator supports NAT and bridged network connections

A

A. Verify the system requirements of the hypervisor
B. Verify the hypervisor software supports the emulator needed for testing

61
Q

What printer issue is most likely resolved by performing a calibrate function on a laser or inkjet printer?
A. Misaligned colors on printed page
B. gradual fading over time as the pages are printed
C. misfeeds (no paper being pulled from the paper tray)
D. multiple sheets pulled from the paper tray at one time
E. viods in one or more colors on a printed page

A

A. Misaligned colors on printed page

62
Q

A company is utilizing servers, data storage, data backups, and software development platforms over an internet connection.
What describes the company’s approach to computing resources?
A. Cloud computing
B. thick client computing
C. client-side virtualization
D. internal shared resources

A

A. Cloud computing

A+ Certification (2022) (21 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions