Carpentry

Question 1

Using a 1/4”: 1’ scale, 3 1/2” will represent

Answer 1

14’

Question 2

Lines that terminate with arrows

Answer 2

Dimension line

Question 3

Show building with boundaries

Answer 3

Plot or Site Plan

Question 4

Designates brand and model number of window

Answer 4

Window schedule

Question 5

Concrete is made of four parts

Answer 5

Water, sand, cement, aggregate

Question 6

Affects the weight of concrete the most

Answer 6

Aggregate

Question 7

Added to concrete to slow set up

Answer 7

Retarder

Question 8

Added to concrete to control durability

Answer 8

Water

Question 9

The wetter the concrete, the ____ the slump

Answer 9

greater

Question 10

To remove air from concrete

Answer 10

Vibrate

Question 11

The #5 rebar is ____ inch thick

Answer 11

1 = 1/8”

5/8”

#4 = 4/8”
#6 = 6/8”

Question 12

Measures horizontal angles only

Answer 12

Builders level or dumpy level

Question 13

Starting point for laying out a building

Answer 13

Benchmark

Question 14

If layout for a rectangular building is square

Answer 14

Diagonals are equal

Question 15

Install batter boards when

Answer 15

The grade and the corners have been established

Question 16

Minimum placement of batter boards from the point of excavation

Answer 16

4’

Question 17

If rod “A” reads 5’ and “B” reads 5’6”

Answer 17

A is 6” higher than B

Question 18

Estimating concrete in cubic yards

Answer 18

L x W x D / 27

Question 19

Footings do not directly support

Answer 19

Headers or lintels

Question 20

Used over window and door openings in concrete block wall

Answer 20

Lintels

Question 21

A standard mortar joint in block construction is

Answer 21

3/8”

Question 22

Nominal size of a standard block CMU

Answer 22

8x8x16”

Question 23

Unused mortar should be discarded after

Answer 23

2.5 hours

Question 24

When lumber dries, it tends to shrink

Answer 24

More in width than length

Question 25

When a piece of umber is cut along the natural age ring, it is called

Answer 25

Shake

Question 26

Place crown on glulam beams
(camber / steel)

Answer 26

Up or on top

Question 27

Minimum quality of plywood used for a concrete form

Answer 27

B-B

Question 28

Horizontal members that carry the heaviest load of attached horizontal members

Answer 28

Girder

Question 29

If joist depth is D, what is the maximum size hole that can be drilled in it?

Answer 29

D/3

Question 30

A hole drilled into a joist must be at least ____ from the top or bottom

Answer 30

2”

Question 31

A notch in a joist may not be located in the

Answer 31

middle third of the joist

Question 32

A notch in a joist must not be larger than

Answer 32

D/6

Question 33

A corner notch in a joist must not be larger than

Answer 33

D/4

Question 34

Subfloor plywood underlayment spacing is

Answer 34

1/8” on ends and sides

Question 35

Support under a wood deck is

Answer 35

Girder

Question 36

Standard height for interior doors

Answer 36

6’8” or 80”

Question 37

Correct order for hanging bi-fold door

Answer 37

Top track first, then fasten the lower track to the floor directly under the top track

Question 38

Door hinge size for a 1 3/8” interior door

Answer 38

3 1/2”

Question 39

Door installations call for install the door stop _____ first

Answer 39

Lock side

Question 40

Installation of drip edgeL

Answer 40

Under underlayment at the eaves but over the underlayment at the rake

Question 41

Starter course of shingles

Answer 41

Over the eaves flashing

Question 42

Ventilation for a hip roof

Answer 42

Soffit vents

Question 43

Strip nailed to the ends of the rafter

Answer 43

Fascia

Question 44

Installation plywood soffit, nails should be installed

Answer 44

6” apart