AF213 FAA Practice Quiz #1 Flashcards

1
Q

Which seals are used with petroleum base hydraulic fluids?

A

Buna-N

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Where can information be obtained about the compatibility of fire-resistant hydraulic fluid with aircraft materials?

A

Fluid manufacturer’s technical bulletins.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Pressure is a term used to indicate the force per unit area. Pressure is usually expressed in

A

pounds per square inch.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Seals used with a mineral base hydraulic fluid are identified by which color code?

A

Blue dot or stripe.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

If a rigid tube is too short for the flare to reach its seat before tightening, pulling it into place by tightening

A

may distort the flare.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Hydraulic system accumulators serve which of the following functions? 1. Dampen pressure surges. 2. Supplement the system pump when demand is beyond the pump’s capacity. 3. Store power for limited operation of components if the pump is not operating. 4. Ensure a continuous supply of fluid to the pump.

A

1, 2, 3.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Pneumatic systems utilize

A

relief valves.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

In a gear-type hydraulic pump, a mechanical safety device incorporated to protect the pump from overload is the

A

shear pin

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which must be done before adjusting the relief valve of a main hydraulic system incorporating a pressure regulator?

A

Eliminate the action of the unloading valve.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Generally, the first step in removing an accumulator from an aircraft is to

A

relieve system pressure.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

(1) When servicing aircraft hydraulic systems, use the type fluid specified in the aircraft manufacturer’s maintenance manual or on the instruction plate affixed to the reservoir or unit. (2) Hydraulic fluids for aircraft are dyed a specific color for each type of fluid. Regarding the above statements,

A

both No. 1 and No. 2 are true.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

One of the main advantages of skydrol is its

A

wide operating temperature.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Which is true regarding the ground check of a flap operating mechanism which has just been installed?

A

If the time required to operate the mechanism decreases with successive operations, it indicates the air is being worked out of the system.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

After installation of a rebuilt hydraulic hand pump, it is found that the handle cannot be moved in the pumping direction (pressure stroke). The most likely cause is an incorrectly installed

A

hand pump outport check valve.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Which of the following lists only desirable properties of a good hydraulic fluid that has chemical stability?

A

Low viscosity, high flash point, high fire point.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The internal resistance of a fluid which tends to prevent it from flowing is called

A

Viscosity.

17
Q

A flexible sealing element subject to motion is a

A

Packing.