120101b-kB Flashcards by Megan Read

Who is ultimately responsible for ensuring the integrity of the rigging equipment prior to each shift?
A) employee
B) employer
C) supervisor
D) consultant

B) employer

How well did you know this?

Not at all

Perfectly

What must always be present on a sling before it is used?
A) protective coating
B) a label
C) and expiry date
D) a thimble

B) a label

How well did you know this?

Not at all

Perfectly

What is the minimum ultimate load ratio for a chain?
A) 1:1
B) 2:1
C) 4:1
D) 5:1

C) 4:1

How well did you know this?

Not at all

Perfectly

List 3 things synthetic web slings should be inspected for

Missing or unreadable tags
Visible signs of melting, charring, cuts, tear, chemical damage
Signs of excessive wear or fraying

How well did you know this?

Not at all

Perfectly

What does WLL stand for?

Working load limit

How well did you know this?

Not at all

Perfectly

Why have most workplaces reduced their use of synthetic ropes for lifting and hoisting?
A) they often fray or tear during the lift
B) they have a lower engineer rating
C) it is difficult to balance using them
D) there are too many types of knots

B) they have a lower engineer rating

How well did you know this?

Not at all

Perfectly

_________ a wire rope can expose broken wires in the valley between strands

Flexing

How well did you know this?

Not at all

Perfectly

Plate clamps are equipped with what type of jaw?
A) serrated
B) Knurled
C) magnetic
D) all of the above

A) serrated

How well did you know this?

Not at all

Perfectly

With regards to U-bolt, what does the phrase never saddle a dead horse refer to?
A) the saddle must always be on the live/ loaded end
B) the saddle, must always be on the dead (non loaded) end
C) the U-bolt must always be on the live ( loaded ) end
D) you must put two U-bolt on the live/loaded end

A) the saddle must always be on the live/ loaded end

How well did you know this?

Not at all

Perfectly

When using a plate clamp to pull or lift a plate make sure your line is _________ to prevent it from releasing and sliding off.

Directly overhead

How well did you know this?

Not at all

Perfectly

________ must be retorqued after the rope is subjected to a load for an hour or two and periodically after that.

Wire rope clips

How well did you know this?

Not at all

Perfectly

The ______ is the weight that can be safely lifted by a wire rope.

WLL

How well did you know this?

Not at all

Perfectly

Calculate the working load limit for a 3/4” diameter wire rope in tons.
Hint
WLL=d^2 x8

WLL=D^2 x 8
=.75 x .75 x 8
= 4.5 tons

How well did you know this?

Not at all

Perfectly

What is the safety factor for wire rope when lifting people?
A) 5:1
B)8:1
C)10:1
D)15:1

C) 10:1

How well did you know this?

Not at all

Perfectly

Explain safety factor

A safety factor is a ratio that provides a margin of extra strength so that even if extra stresses are placed on the rope, it will not fail in other words safety factor refers to

how much stronger the system is compared to what is required

How well did you know this?

Not at all

Perfectly

List the 4 steps taken to ensure that the sling angle is safe for lifting.

Measure the length of the sling leg and fittings.
Find the centre of gravity of the load.
Measure an equal distance on either side of the centre of gravity equal to half the length of the sling leg and fittings.
position the sling legs to these two points before making the lift.

How well did you know this?

Not at all

Perfectly

What is the arc radius that the rope in the sheave should be supported at?
A)60-90
B)90-120
C)120-150
D)150-180

C)120-150

How well did you know this?

Not at all

Perfectly

You provide a mechanical advantage with the use of ___________ to safely move a load that is greater in weight than the WLL of the single rope?

Blocks

How well did you know this?

Not at all

Perfectly

In what situation is it appropriate to use an anchor shackle?

When two slings are used to lift a load in a bridal sling arrangement the anchor shackle is an appropriate equipment selection

How well did you know this?

Not at all

Perfectly

List two actions that can be used to safely apply force when guiding and following a suspended load

Apply a sideways force always pushing the load away from you.
Use a rope to pull the load to avoid back screen or entrapment.

How well did you know this?

Not at all

Perfectly

A _________ must watch the load; the __________ must watch you.

Signal person
Operator

How well did you know this?

Not at all

Perfectly

If a signal person throws both arms outward, what is he signaling?

Emergency stop

How well did you know this?

Not at all

Perfectly

If a signal person has one hand out stretched and flat and the other hand giving a thumbs up signal underneath that hand, what is he signaling?

Raise the boom slowly

How well did you know this?

Not at all

Perfectly

What standard must a full body harness meat?
A) WCB
B) ULC
C) PPE
D) CSA

D) CSA

How well did you know this?

Not at all

Perfectly

How often must you inspect your fall arrest equipment? A) before use on the first shift of the week B) before use on the first shift of the month C) before use on each shift D) only after the equipment was used to protect you from a fall

C) before use on each shift

What is the minimum distance a ladder must protrude above the intended landing point? A) .3m (1ft) B) 1m (3ft) C) 1/4 the length of the ladder D) 1/4 the distance of the base of the ladder from the base of the wall or structure

B) 1m (3ft)

The safety factor for scaffold must be designed and constructed to support at least? A) three times the load that may be imposed on it B) four times the load that may be imposed on it C) five times the load that may be imposed on it D) six times the load may be imposed on it

B) four times the load that may be imposed on it

At what height must the employer have a guard rail erected for a temporary work area? A) 2.4 M or 8’ B) 3.0 M or 10’ C) 3.7 M or 12’ D) 4.2 M or 14’ going to be 3.7 m

B) 3.0 M or 10’

When conducting a hazard assessment related to lifting and handling a load, your employer must consider the A) weight size, and shape of the load B) cost of renting moving equipment C) insured value of the load to be moved D) number of people required to move the load

A) weight size, and shape of the load

What is not an example of a recommended lifting technique? A) avoid awkward postures B) lift loads smoothly C) lift no higher than eye level D) Begin lifting at knee level

C) lift no higher than eye level

What is the goal of proper lifting technique? A) to constantly practice lifting to become more skilled B) to increase lifting efficiency and capacity with practice C) to increase the number of lifts performed each day D) to eliminate loading stress on the soft tissue of your lower back

D) to eliminate loading stress on the soft tissue of your lower back

How is working load limit defined? A) breaking strength divided by the safety factor B) safety factor divided by the breaking strength C) the ultimate tensile strength (UTS) D) the safest way to move and lower a load

A) breaking strength divided by the safety factor

What does the term shock loading mean when applied to rigging equipment? A) a stray spark from a work operation occurs when the sling has load applied to it B) the sling is exposed to stress from the load, suddenly starting or stopping C) the sling contacts and electrical conductor when the sling is loaded D) the sling is used as an electrical conductor to connect to a load sensor in the lifting equipment

B) the sling is exposed to stress from the load, suddenly starting or stopping

What rigging factor of safety is to be used when lifting and transporting workers? A) 2:1 B) 5:1 C) 10:1 D) 20:1

C) 10:1

How often should rigging be inspected?

At the beginning of each work shift

What is the recommended sling angle when rigging a load? A) must never be greater than 45* B) must never be less than 45* C) must never be greater than 60* D) must never be less than 60*

D) must never be less than 60*

Before attempting to lift an object, you should determine its? A) length B) Width C) Weight D) Height

C) Weight

If you must carry a heavy object, what is the best way to hold it?

Close to your body

What should you do if you’re helping to move a suspended load

Guide and follow the load

What is the safest method of storing loose materials? A) put them in containers or bins B) pile them into the shape of pyramid C) stack them according to size on shelves D) stack them against the wall, according to length

A) put them in containers or bins

What is the hand signal for an emergency stop when hoisting a load?

Both arms straight out from your shoulders.

Which signal indicates boom down? A) arm position, horizontal and thumb pointing down B) arm position, horizontal, and thumb pointing up C) arm position, horizontal, and fingers pointing down D) arm position, vertical and thumb pointing down.

A) arm position, horizontal and thumb pointing down

Which signal indicates hoist load? A) arm straight out with thumb pointing upwards B) arm, vertical with fingers pointing upwards C) both arms straight up in a vertical position D) forearm, vertical forefinger pointing up small circles.

D) forearm, vertical forefinger pointing up small circles.

Which signal indicates to lower the boom and raise the load? A) thumb pointing down and other hand under thumb B) thumb pointing up other hand above thumb C) thumb pointing down and fingers moving back-and-forth D) pointing up and fingers moving back-and-forth

C) thumb pointing down and fingers moving back-and-forth

A knot in a fibre rope can reduce the strength of the rope by approximately A) 5% B) 15% C) 50% D) 85%

C) 50%

A Clovehitch A) can be used to attach rope to a post or pipe B) can be used to hold personnel C) reduces the fibre rope to 25% of its working strength D) is a good non-slip knot

A) can be used to attach rope to a post or pipe

A bowline knot A) slips easily when load is applied B) can be used for hoisting safety personnel C) is easy to tie an untie when a load is applied D) is a hitch knot

C) is easy to tie an untie when a load is applied

What hitch would be best used as a back up to other knots/hitches? A) Timberhitch B) cats paw C) Halfhitch D) Carrick bend

C) Halfhitch

Which synthetic fibre rope is the strongest A) nylon B) polyester C) polypropylene D) polyethylene

A) nylon

What is the approximate weight of a piece of steel that is 305mm x 305mm and 25.4mm thick (1 foot x 1 foot & 1” thick) ? A) 4.5 KG or 10 LB B) 18.5 KG or 40 LB C) 37 KG or 80 LB D) 45.5 KG or 100 LB

B) 18.5 KG or 40 LB

Where is the centre of gravity of an object located? A) at the point where it weighs the least B) at the point where it lands when dropped C) at the point that causes it to top over D) at the point where the object balances

D) at the point where the object balances

What can happen if you lift a load with the centre of gravity above the lifting points?

It could tip over or shift

What is the safety factor for wire rope when lifting people? A) 5:1 B) 8:1 C) 10:1 D) 15:1

C)10:1

The working load limit for wire rope is D^2 x 8 = WLL in tons. What is the WLL of 3/4” diameter wire rope A) 4.5 tons B) 5.6 tons C) 10.6 tons D) 12 tons

A) 4.5 tons

Which statement is true with respect to synthetic web slings? A) they are heavier than wire rope slings B) they are lightweight and very flexible C) they can lift on corners without padding D) irregularly shaped loads, cannot be lifted

B) they are lightweight and very flexible

What is the approximate maximum working load for a 3“ wide nylon sling (8000lb/in material) using a single choker hitch? A) 2400 lb B) 3600 lb C) 4800 lb D) 9600 lb

B) 3600 lb

What is the maximum number of plates that can be lifted safely using a plate clamp with a locking grip? A) 1 B) 2 C) 3 D) as many as well fit between the jaws

A) 1

When U-Bolt type clips are used for wire rope fastening where is the U-bolt section applied? A) on either side of the rope B) alternating on each side C) on the live end of the rope D) on the dead end of the rope

D) on the dead end of the rope

What does WLL stand for

Working Load Limit

What does SWL stand for

Safe working load

Describe the term splice.

Made by joining the ends of two rope by making an eye splice from a single rope and doubling it back on itself

How much is a rope strength reduced after a knot or bend has been added?

50%

What is the normal safety factor when lifting objects?

5:1

What is the safety factor for hoisting personnel

10:1

What is the safety factor for lifting the public ( elevator)

20:1

Describe the benefits of a bowline knot.

Easy to tie & untie Does not slip easily Used for hoisting safety lines and hitching around posts

Describe the benefits of a Figure 8 knot.

knot does not slip easy to untie when a load is applied used for safety lines when personnel are tying into a safety harness

Describe the benefits of a Catspaw hitch.

Used to attach a rope to a hook for transport and not hoisting

Which type of rope material provides the greatest strength?

Nylon

List 2 reasons why polypropylene is the most popular rope available

Economical $ light weight doesn't absorb moisture & floats retains flexibility when cold resistant to most acids, alkalis withstands impact loading excellent non conductor

What material are wire rope slings made of?

Carbon or stainless steel

Why is a thimble added to wire rope slings?

extends the life of the sling by preventing wear on the eye of the sling while in use

What are 3 signs of damage to tag out a sling

Valley Breaks Broken Wires Excessive surface wear

What is shock loading?

any sudden movement of the load by the hoisting equip

Why are synthetic slings so popular?

Lightweight Great flexibility Allows the rigger to fasten the sling quickly and safely

What are 3 reasons you may tag out a chain sling?

Bent Links Twisted Links Stretched Links beyond 10% of length of a new chain of the same size

Who is responsible for inspecting of all rigging equip prior to the start of each shift

The employer

What must always be present on a sling before its used

A label

What is the min ultimate load ratio for a chain

4:1

What is the saying for how to attach a U-Bolt or Single Saddle

Never saddle a dead horse

Plate clamps are equipped with what type of jaw a) serrated b) Knurled c) Magnetic d) all of the above

A) serrated

What does the term never saddle a dead horse refer to a) The saddle must always be on the live & loaded end b) the saddle must always be on the dead end ( non loaded) c) The u-bolt must always be on the live end d) you must put 2 U-bolts on the live end

a) The saddle must always be on the live & loaded end

_________ must be re-torqued after the rope is subjected to a load for an hour or two and periodically after that

Wire rope clips

Practice calculating WLL page 28

Explain Safety factor

how much stronger a system is compared to what is required

What is the recommended sling angle?

60%

Brainscape's Knowledge GenomeTM

120101b-kB Flashcards

Brainscape's Knowledge Genome^TM