Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

march 2016 exam > Weapons Assembly > Flashcards

Weapons Assembly Flashcards

1
Q

The plastic shipping plugs are removed from the nose well and the tail fuze cavity of MK 80 GP bombs at which of the following times

A

During depalletizing procedures

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is the indication of the FMU-139 series fuze when the saving pin is removed and the red and black striping is visible on the gag rod sleeve

A

Fuze is enabled and could be armed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is the proper orientation of an MK 122 arming safety switch coaxial cable when installed in the BLU-110

A

All answers are correct
A. Left angle to the lugs
B. Forward of the lanyard
C. 45 degree angles to the lugs

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

When tightening the clamp bolt of the BSU-33 fin to the bomb body what must you ensure

A

The fin clamping ring contacts within V-groove of bomb body 360 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What component retains the firing pin assembly of the MK 76 practice bomb

A

A cotter pin

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Where is the MK 89 spotting charge adapter installed in the BDU-45

A

Bomb tail well

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What is the acronym GBU

A

Guided bomb unit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What is the first inspection step you must perform on the MXU-667 AFG once you have removed it from its container

A

Verify safety pins and streamers are installed in latch release lever and collar of wing assembly

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What must you care about when exercising the PRF switches on the MAU-169 , MAU-209 , and WCU-10

A

That switch stop limits are not exceeded

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

A complete JDAM guidance set consists of a tail assembly and _______ assembly

A

Aero surface

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

When inspecting the CBU-99 fin release band for installation of safety cotter pin what must you ensure

A

Safety cotter pin prong is bent to 15-30- degree angle

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Before a reusable rocket launcher is loaded onto an aircraft , it should be sent to AIMD for which of the following reasons

A

An electrical checkout

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

When a rocket warhead is inspected , what maximum amount of gap , if any , is allowed between the fuze adapter and the warhead

A

No gap is allowed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Which of the following devices should be in place whenever a rocket motor is removed or protrudes from a rocket launcher

A

A shielding band

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

When inspecting the SLAM-ER in the shipping container , you must inspect the interior for any evidence of damage , engine oil , fuel , ______or _______

A

Battery electrolyte , loose hardware

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What primary factor dictates the way a weapon is to be configured

A

The mission requirements

17
Q

what provides detailed information for weapons uncanning/recanning and inspection , component unpackaging/inspection , repackaging and weapons assembly , and inspection criteria for assembled weapons

A

airborne weapons assembly manual (WAM)

18
Q

regardless of how well trained an assembly crew may be , there must always be a team leader (TL) , a quality assurance (QA) inspector and what other member

A

safety observer (SO)

19
Q

the designated bomb assembly areas on the amphibious assault ship (general purpose) (LHA) and the multi-purpose amphibious assault ships (LHD) class is normally located on what deck (aviation ordnance/bomb assembly magazine) or other designated assembly areas depending on the class of ship

A

5th

20
Q

what is the term used to define the physical removal of ammunition from the magazine

A

breakout

21
Q

weapons are broken out , by direction of whom , in accordance with the load plan

A

Ordnance Handling Officer (OHO)

22
Q

bombs , with more than 56 square inches of thermally protected , and are restricted from use afloat

A

15

23
Q

the navy currently used what series of electronic bomb fuze

A

FMU-139

24
Q

when stored in original shipping/storage container , the shelf life of BSU-85 fins is how many years

A

20

25
Q

unless the BSU-86 fin is used on MK 82/BLU-111 live loaded tactical Depth bomb , ensure that the eight set crews are made of what

A

steel

26
Q

the practice bombs normally used on a routine basis are the MK 76 Mod 5 and what else

A

BDU-48

27
Q

don’t make changes or additions to any ordnance or ordnance components without explicit authority from the what

A

Naval Air Systems Command

march 2016 exam (30 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions