Standard Calls Revision Flashcards
When do you call ‘SPEED’ during final approach
‘SPEED’ If speed decreased below target by -5kts or above by +10kts
When do you call ‘SINK RATE’ during final approach
‘SINK RATE’ When descent rate exceeds -1000ft/min
WHen do you call ‘BANK’ during final approach
‘BANK’ when bank angle becomes greater than 7 deg
When do you call ‘PITCH’ during final approach
‘PITCH’ when pitch attitude is lower than -2.5 deg or higher than +10 deg
When do you call ‘LOC’ or ‘GLIDESLOPE’ during final approach
‘LOC’ when deviation is greater than 1/4 Dot
‘GLIDESLOPE’ when deviation is greater than 1 Dot
When do you call ‘VASIS’ or ‘PAPI’ during final approach
‘VASIS’ or ‘PAPI’ when deviation is greater than 1 light.
When do you call ‘COURSE’ during final approach
‘COURSE’ when greater than 1/2 dot or 2.5 deg (VOR)
‘COURSE’ when greater than 5 deg (ADF)
When do you call ‘__ FT HIGH (LOW)’ during final approach
‘___ FT HIGH (LOW)’ at altitude check points
When do you call ‘LDEV’ on a RNAV Approach with LNAV/VNAV Minima
‘LDEV’ when LAT DEV 1 Dot or XTK is greater than 0.1nm if LDEV is not available
When do you call ‘LDEV GO AROUND’ on a RNAV Approach with LNAV/VNAV Minima
‘LDEV GO AROUND’ when LAT DEV > 2 Dots
When do you call ‘VDEV’ on a RNAV Approach with LNAV/VNAV Minima
‘VDEV’ when VERT DEV > 1/2 dot below * (50 ft)
When do you call ‘VDEV GO AROUDN’ on a RNAV Approach with LNAV/VNAV Minima
‘VDEV GO AROUND’ when VERT DEV > 3/4 dot below * (75 ft)
When do you call ‘LDEV’ during the Final approach of an RNAV (RNP)
‘LDEV’ when LDEV is 1/2 Dot
Applicable inside the IAF
When do you call ‘LDEV GO AROUND’ during the Final approach of an RNAV (RNP)
‘LDEV GO AROUND’ when LDEV > 1 Dot
Applicable inside the IAF
When do you call ‘VDEV’ during the Final approach of an RNAV (RNP)
‘VDEV’ When VERT DEV is 1/2 dot below *(50ft)
Applicable inside the FAF
When do you call ‘VDEV GO AROUND’ during the Final approach of an RNAV (RNP)
‘VDEV GO AROUND’ when VERT DEV > 3/4 dot below * (75ft)
Applicable inside the FAF
When do you call ‘SINK RATE’ during the Final approach of an RNAV (RNP)
‘SINK RATE’ when VS is greater than -1200 ft/min
(different to normal approach)
When do you call ‘BANK’ during the Final approach of an RNAV (RNP)
‘BANK’ when bank angle above 30 Deg
When do you call ‘PITCH PITCH’ during Landing
‘PITCH PITCH’ if Pitch attitude approaches the tail strike pitch limit indicator or reaches 10 deg
When do you call ‘BANK BANK’ during landing
‘BANK BANK’ if bank angle reaches 7 deg
When do you call ‘BANK’ during a Go Around
‘BANK’ if the bank angle becomes greater than 7 deg
When do you call ‘PITCH’ during a Go Around
‘PITCH’ if the pitch attitude becomes greater than 20 deg up OR less than 10 deg nose up
When do you call ‘SINK RATE’ during a Go Around
‘SINK RATE’ if there is no climb rate.
