Specialty Hand Tools Flashcards

1
Q

Tubing used in hyraulic brake lines must be made from:

A

double-wrapped, brazed steel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Two styles of tubing flares used by most vehicles manufacturers are

A

SAE double and SI (ISO) bubble flare

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Tubing should be cut with a

A

tubing cutter

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

The drill point angle for a twist drill should be

A

59 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

The lip clearance angle for a twist drill should be

A

12 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Twist drill sets may be sized using

a) fractions
b) letters and numbers
c) metric
d) all of the above

A

d) all of the above

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Three taps commonly found in a set of imperial taps are

a) metric, imperial and pipe
b) ISO, HSS and HBO
c) taper, plug, bottoming
d) UNC, UNF and NPT

A

c) taper, plug and bottoming

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

A tap marked 5/16 x 24 UNF will create threads with

a) 24 threads per inch
b) 1/24 pitch
c) a maximum diamet of 5/16”
d) all of the above

A

d) all of the above

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Technician A says that when using a tap, it should be backed up 1/2 a turn after each 1/4 turn of cutting. Technician B says that using a tap handle is not necssary and that the square drive on the end of a tap may be driven with a crescent wrench. Who is correct/

A

Technician A

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

To remove a broken stud you could use a

A

screw extractor

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Damaged internal threads may be repaired using

a) helicoil
b) tap-loc insert
c) neither a or b
d) either a or b

A

d) either a or b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What tools do you need to properly form a tubing flare?

A

1) tubing cutter
2) tubing reamer
3) tubing flaring tool kit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What does a tubing flaring kit consist of?

A

1) gripping or flaring bar
2) rod handle
3) yoke
4) adapters

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What are the three main parts of a twist drill

A

shank, body and point

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What information can be found on the shank of a twith drill

A

size and the material its made of

HSS - High speed steel

HC - High Carbon

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

How do you measure the diameter of a twist drill bit?

A

a) across the margins along the flutes.

b) read the identifying marks on the shank
c) use a drill gauge

17
Q

What is the included angle of a standard twist drill bit?

A

118 degrees

18
Q

The larger the drill bit, the _____ the speed

A

slower

19
Q

The harder the material you are drilling the _______ the speed

A

slower

20
Q

What do you use cutting fluid for when drilling?

A

cools the drill and retains the cutting edge

cools the work piece

helps wash away the chips

allows for faster cutting speeds

improves the finish of the hole

21
Q

What is tapping

A

the process of cutting internal threads in a previously drilled hole

22
Q

How do we determine what size hole to drill when tapping a hole

A

1) Use a tap dril chart
2) Calculate using

Bolt size minus Pitch