safety Flashcards

1
Q

What type of outlet protects the technician from electrical shock?

A

GFCI or GFI outlet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

In identifying utility locate colors, What colors represent power, telecommunications, and water?

A

Red, Orange, and Blue

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is the minimum clearance between CATV and power at the house?

A

12 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What is the minimum clearance between CATV and all points above a flat roof?

A

10.5 feet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Up to how much stress can be placed on your back when a 75 pound object is lifted improperly?

A

750 pounds (3-10 times acceptable)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

When routing underground drop cable parallel to lot lines, what minimum distance must be maintained from those lines?

A

4 feet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What test is performed to determine if gaffs are properly shaped and sharpened?

A

Cut-out test

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What type of sleeves protect pole climbers against splitters and abrasions?

A

Kevlar

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

During which pole test should you be careful not to let power lines swing together?

A

Rocking Test (Push Test)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

When working on a pole with gaffs, how far from the pole should you keep for proper knee/gaff alignment?

A

8 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What is the visibility rating on a clear night for a road’s barriers’ Type B High Intensity Warning Light?

A

1000 feet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is the maximum allowable noise level before hearing protection is required?

A

90 dB

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

When it’s properly adjusted, a hard hat can absorb approximately which percent of the force of a blow?

A

75%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

At what level dBA must ear protection be worn?

A

above 90 dBA

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

How often should the lower controls of an aerial lift be tested?

A

Daily

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What is the recertification timeframe for confined space certification?

A

Every 3 years

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

Which type of sign gives notice to road users of a situation that might not be readily apparent?

A

Warning Sign

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

What term describes a detailed thorough analysis of all of the features currently existing at the customer site?

A

Site Survey

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

What is the term for the right to use another person’s real estate for a specific purpose?

A

Easement or Right-Of Way

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

How many feet should a ladder be angled per 4 feet of height?

A

1 foot

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

What are the three protection methods that should be used when working above 4 feet on a tower?

A
  1. a fixed cable system2. a double lanyard system3. a retractable device
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

What must be marked on all safety glasses to ensure that they meet ANSI requirements?

A

Z87

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

Before breaking down a ladder, how far should the feet be from the leaning surface?

A

2 feet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

If a vehicles weight and speed both double, the braking requirement increases by what factor?

A

8

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

What term describes scanning the area in front of your vehicle from sidewalk to sidewalk?

A

The 45-degree eye scan

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q

What is the formula for ascending a pole using the hitchhiking technique?

A

Belt, Step-Lock-Step, Belt

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q

What agency provides direction for state and local emergency planning officials in the EAS?

A

FEMA (Federal Emergency Management Administration)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
28
Q

Which 3 items would you look for on an OSHA inspector’s ID card?

A
  1. Photo2. Serial number3. Signature of the Secretary of Labor
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
29
Q

What is the proper angle of your safety strap when you are belted onto a pole?

A

5 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
30
Q

When pole climbing, what is the proper angle of your leg when striking the pole?

A

30 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
31
Q

How much time should be added to the 3 to 4 second rule when towing a trailer?

A

2 seconds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
32
Q

What are the three basic types of signs?

A

Warning, Guide, and Regulatory

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
33
Q

What construction practice consists of a wall or floor assembly, a penetrating item passing through an opening in the assembly, and materials designed to prevent the spread of a fire?

A

Firestop System

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
34
Q

What are the 2 “short distance” methods for carrying a ladder?

A

Half-Vertical / Half-Horizontal and Side Vertical (LH)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
35
Q

When a ladder is extended to 20 feet, how far from the base of the pole should its feet be positioned?

A

5 feet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
36
Q

Which parts of a ladder bear all of its weight and pressure when properly positioned on the pole?

A

Ladder feet and the V-rung

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
37
Q

Name 3 of the 4 decals placed on your aerial lift truck.

A

Caution, Danger, Warning, Operating Instructions/Notice

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
38
Q

What are the four ways to carry a ladder?

A
  1. Horizontal carry at the shoulder2. Horizontal carry at the hip3. Half-vertical, Half-horizontal carry4. Side vertical carry
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
39
Q

What is the position of the base section of the ladder when it is properly loaded onto a vehicle?

A

Facing down or on the bottom

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
40
Q

When do the 2 foot-15 foot rule apply?

A

When setting up a road side workzone - 2 feet from curb or 15 feet from the edge of a roadway.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
41
Q

Relative to time and “eye lead time”, how far in advance is the recommended scan while driving?

A

12 to 15 seconds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
42
Q

What is the first thing you do if you are involved in an automobile accident on the job/

A

Protect/Secure the scene

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
43
Q

Commtech work shirts should be made of what material?

A

100% Cotton

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
44
Q

Which rule determines how far you should lean laterally when working on a ladder?

A

Belly-button rule

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
45
Q

What is the maximum number of tool loops OSHA allows on a body belt used for climbing?

A

4

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
46
Q

Which two vehicle accessories should be addressed before lowering the ladder with a sidewinding rack?

A

Mirror and Antennae

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
47
Q

Which piece of PPE should only be cleaned with soap and water?

A

Hardhat

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
48
Q

What term describes having your view of the road blocked by another vehicle?

A

Billboarding

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
49
Q

What is the national “Call Before You Dig” number?

A

811

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
50
Q

Where should your eyes be focused while ascending or descending your ladder?

A

Your feet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
51
Q

Which is directly impacted by space for the vehicle and visibility for the driver?

A

Response time

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
52
Q

When climbing, what should the proper angle of your ladder be in degrees?

A

75 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
53
Q

“Safety Is _________ ______________.”

A

Everyone’s Responsibility

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
54
Q

Vehicle Tip #1: How far ahead should you look while driving?

A

At least two blocks ahead of you, and even up to a quarter of a mile ahead on higher speed roadways.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
55
Q

Vehicle Tip #2:What should you do before entering an intersection?

A

Look both ways, even if you have the right of way.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
56
Q

Vehicle Tip #3:When stopped at a red light before entering the intersection you should?

A

Count to two or three -especially if there is a car in front of you.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
57
Q

Vehicle Tip #4:Use the _____ - or - ____ - second rule when following a vehicle.

A

three - or - four

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
58
Q

Vehicle Tip #5:Increase your following distance to ___ or ____ seconds in wet or snowy weather.

A

six or more

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
59
Q

Vehicle Tip #6:When you’re at a signal light or stop sign you should?

A

Stop where you can see the tires of the vehicle in front of you touching the ground. (If in a van stay about 10’ back.)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
60
Q

Vehicle Tip #7:Where should cones be placed when your vehicle is parked?

A

In front and behind. You will need both in most situations depending on how you’re parked.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
61
Q

Vehicle Tip #8:What are the first, second, and third parking choice

A

1st Choice- Drive In / Drive Out2nd Choice- Back In / Drive Out3rd Choice- Drive In / Back Out

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
62
Q

Vehicle Tip #9:When you back up, have a “_______” guide you, if possible.

A

“spotter”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
63
Q

Vehicle Tip #10:When you must back up you should?

A

Only back the necessary distance to get out of the parking area, and minimize disturbance of traffic flow.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
64
Q

Circle of Safety

A

Place cones upon exiting vehicle.Walk completely around (360 degrees) when picking up cones.Look under vehicle for children, pets, and toys.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
65
Q

“Standard Wear Safety Gear”

A

hard hat, safety glasses, and work boots

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
66
Q

Foreign voltage is?

A

Any AC voltage that may be present on a conductor that is not designed to carry, or would not normally carry, a current.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
67
Q

Your FVD allows you to?

A

Test potential conductors as you move towards them.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
68
Q

An employee working from a pole shall NOT?

A

Leave the pole or transfer one’s weight to an adjacent object (e.g., ladder, aerial lift, tree, fence or any other object).

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
69
Q

While working aloft secure yourself to the LADDER & POLE. Ensure the safety strap is?

A

Around the pole and through the ladder, under the top rung.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
70
Q

While working aloft secure yourself to the LADDER & STRAND. Ensure the safety strap is?

A

Around the strand and through the ladder, under the top rung.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
71
Q

When securing yourself to the strand, the _______ method is recommended and will help prevent the ladder from sliding.

A

1-1-1

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
72
Q

1-1-1 method is: From the D-ring

A

1- Wrap the safety strap around the strand outside the ladder.1- Wrap it again between the rails including the strand and top rung.1- Wrap it a third time around the strand outside of the opposite rail and then back to the opposite D-ring.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
73
Q

When placing ladder on midspan with drop,

A

place ladder on opposite side of drop to reduce tension on drop line.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
74
Q

When replacing a mid-span drop

A

1) Disconnect at house first.2) Place ladder opposite drop / house.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
75
Q

While placing the ladder on the mid-span with multiple drops on either side of the span you should?

A

Disconnect drops (after informing customers) on at least one side of the span. Place the ladder opposite any remaining drops that could not be disconnected.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
76
Q

Work zone setup will vary depending on?

A

Work durationWork locationRoadway type

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
77
Q

Older transformers may contain _______________ _________ which are a cancer-causing agent.

A

polychlorinated biphenyls (PCBs)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
78
Q

Work should not be conducted within __ feet of a roof edge unless fall arrest systems are in place.

A

6 feet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
79
Q

____ __________may be used as fall protection provided they meet the regulatory requirements for top and midrails, toeboards, and strength.

A

Roof guardrails

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
80
Q

No COMCAST employee is required to administer_____ ___.

A

first aid

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
81
Q

If you are working on strand and see lightning,

A

get down from the ladder/pole and wait 15 minutes inyour vehicle. If no lightning is observed, return towork. If you see another bolt, wait another 15minutes.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
82
Q

Traffic cones shall be predominantly ______ in color.

A

orange

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
83
Q

Traffic cones shall be made of?

A

A material that can be struck without causing damage to the impacting vehicle.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
84
Q

Cones must be a minimum of __ tall and be _____________ if used at night.

A

28”reflectorized

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
85
Q

Cones-

A

28” tall, reflectorized

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
86
Q

Drums-

A

36”tall, 18” wide, orange with white 4-6” wide alternating stripes(top stripe must be orange)

87
Q

Barricades-

A

Type 1 24”wide with 1 horizontal 8” bar. Type 2 24” wide with 2 horizontal 8” bars. Type 3 is 4 feet wide with three 8” horizontal bars.

88
Q

Warning lights-

A

Typically mounted on barricades, drums, vertical panels and signs and should be yellow in color. All warning lights should be mounted at a minimum of 30” from ground to the bottom of the lens.

89
Q

Type A Channelizing Device-

A

Low intensity flashing visible at 3000 feet on clear night (Night use only)

90
Q

Type B Channelizing Device-

A

High intensity flashing should be visible at 1000 feet on a sunny day. (Day or night use)

91
Q

Type C Channelizing Device-

A

Steady burn visible at 3000 feet on clear night. These are used to mark the edge of the traveled way. If used to mark a curve, use only on the outside edge of the curve.

92
Q

4 parts of traffic control zones

A

Advanced warning areaTransition areaActivity areaTermination area

93
Q

5 types of traffic control zones

A

Long Term StationaryIntermediate Term StationaryShort Term StationaryShort DurationMobile

94
Q

Long Term Stationary-

A

Any work that occupies a location more than 3 days.

95
Q

Intermediate Term Stationary-

A

Daytime work that occupies a location for more than 1 and up to 3 days or any nighttime work lasting longer than 1 hour.

96
Q

Short Term Stationary-

A

Daytime operation that occupies a location for more than oneday but less than 12 hours.

97
Q

Short Duration -

A

Work that occupies a location up to one hour.

98
Q

Mobile -

A

Work that moves intermittently or continuously.

99
Q

ANSI rating for hardhats?

A

Z89

100
Q

When a Comcast employee causes minor damage in a customer’s home ($1,500 or less), what phone number should be called to start a claim?

A

1-800-UNIcall

101
Q

Each CommTech’s vehicle is required, at a minimum, to have what safety equipment?

A

A. The number of traffic cones required by applicable lawB.1 Class 2 High visibility safety vest per personC. 1 approved fire extinguisherD. 1 Portable lanternE. 1 First aid kit meeting ANSI requirementsF. 1 Set of emergency triangles(or 3 reflective cones)G. 1 Revolving beacon light (or strobe) mounted securely on the ladder rack

102
Q

3 requirements for technician work pants.

A

A.straight leggedB.no cuffC.either 100% cotton or denim

103
Q

5 of 10 situations in which a hardhat must be worn

A
  1. On a pole2. On a ladder3. In the bucket of an aerial lift4. In an attic or crawl space5. In a confined space6. In a street with traffic7. Below an aerial lift or person on a ladder8. While operating a fork lift9. On a task with the potential for falling or flying objects or where there is a potential for a head injury10. While on a construction site
104
Q

what two types of eye protection should be in field personnel’s vehicles at all times?

A

clear and tinted

105
Q

Name 6 of the 12 tasks in which eye protection should be worn.

A
  1. While using any type of drilling or cutting tool2. While working in trees3. While climbing poles or ladders4. While soldering5. While grinding6.While working in crawl spaces or attics where conditions exist which may expose the eyes to potential injury7. While digging8. While trenching9. While using chain saws10. While splicing fiber optic cable11. While working on construction or line maintenance12. While performing any type of work where the eyes may be exposed to accidental or foreign objects
106
Q

What type of PPE must be worn when handing batteries?

A

A face shield, eye protection, an apron, and rubber gloves

107
Q

6 Characteristics of suitable work boots

A
  1. Lace-up type boot that measures at least 6 inches from the top of the heel2. Steel or fiberglass shank3. Leather construction4. A heel that meets the sole at 90degrees and measures 3/4 inch from sole at purchase and 1/2 of an inch at any time5. A toe that meets the impact and compression protection rating for a nominal impact for 75 foot-pounds, the rating is identified as I/75 C/75 compression ratings6. Meets the electrical hazard protection rating, the rating is identified as EH
108
Q

Name 3 situations when ear protection must be worn

A
  1. when a noise level exists above 90 d.b.a2. Operating light to medium machinery3. Operating a chain saw
109
Q

What is the minimum length a gauntlet must be on gloves when climbing or descending poles?

A

4 inches

110
Q

New Natural Rubber Insulating gloves should be tested by a certified lab after how long?

A

12 months

111
Q

New Synthetic Rubber Insulating gloves should be tested by a certified lab after how long?

A

18 months

112
Q

Re-issued Natural Rubber gloves should be tested by a certified lab after how long?

A

9 months

113
Q

Re-issued Synthetic Rubber gloves should be tested by a certified lab after how long?

A

15 months

114
Q

When should a technician inspect their Insulating gloves?

A

A. When issuedB. Before each useC. After each useD. At least once per month

115
Q

What are the requirements for a Glove Bag for insulated gloves?

A

1.A glove bag is waterproof, flame retardant, and ventilated for air circulation2. the glove bag should have a hook on the rear for attachment to the body belt

116
Q

What test should be performed to verify effectiveness of rubber gloves?

A

The air test

117
Q

4 instances when a shock hazard could occur

A
  1. Grounding to a common ground at a customer’s house or while grounding at the pole.2. when working on a metal sided building, mobile homes and trailers, or aluminum siding3. Whenever there is reason to suspect damage to any utility (test enclosures, pedestals, above ground vaults, etc) before accessing4. Whenever there is a foreign plant on our workspace, including telephone, down guys, etc
118
Q

3 Basic guidelines that need to be followed for climbing.

A
  1. Do not climb any structure, ladder or pole until you have been properly trained2. When climbing towers, you must be connected to the fall protection device and tower at all times.3. All fall protection equipment must be inspected prior to use and at intervals recommended by the manufacturer.
119
Q

When working from an aerial lift, where must the deceleration strap by attached?

A

to the bucket or the boom

120
Q

MUTCD

A

Manual on Uniform Traffic Control Devises

121
Q

FHWA

A

Federal Highway Administration

122
Q

7 goals of proper traffic control techniques

A
  1. Reduce Accidents2. Minimize injury to Comcast Employees and the public3. Reduce damage to private and public property4. Minimize the possibility of claims and litigation arising from work zone accidents5. Reduce confusion to motorist6. Expedite traffic flow7. Improve public image
123
Q

What 3 things should be visually inspected on a power cord before each day’s use?

A
  1. External defects (i.e. deformed or missing pins)2. Insulation damage3. Potential internal damage
124
Q

What should be done with a damaged, bent or broken ladder?

A

It should be tagged immediately and disposed of or repaired as soon as possible

125
Q

How far past the point of support must a ladder be able extend to gain access to a roof?

A

At least 3 feet

126
Q

5 tests to be performed before working on a pole.

A
  1. FVD test2. Sound test3. Prod Test4. Visual Inspection5. Rocking Test
127
Q

What shall be placed on climbers when not being worn?

A

Gaff guards

128
Q

Inadvertently viewing an unterminated or damaged fiber can cause damage if it is how close to an unaided eye?

A

less than 5 to 6 inches

129
Q

What information should be contained in a fiber lock out tag?

A

a. Name of the Technician performing the disconnectb. Date the disconnect is madec. Reason for the disconnect

130
Q

Where can a technician locate a lockout-tagout kit?

A

The HeadendThe Hubsite, and in each fiber restoration kit

131
Q

MSDS

A

Material Safety Data Sheets

132
Q

If there is a hazardous substance spill (such as battery acids, mercury, hydraulic fluids and gasoline) what two steps must an employee take?

A
  1. Clearly identify and protect the area2. Notify your manager/supervisor
133
Q

3 features that define a confined space

A
  1. Large enough and so configured that an employee can bodily enter and perform work2. Has limited or restricted means for entry or exit3. Not designed for continuous human occupancy
134
Q

3 features that define a confined space

A
  1. Large enough and so configured that an employee can bodily enter and perform work2. Has limited or restricted means for entry or exit3. Not designed for continuous human occupancy
135
Q

Before entry into vaults and manholes what tests must be completed?

A

1.Test for combustible gas2. Test for oxygen deficiency ( where continuous forced ventilation is not provided)

136
Q

What 6 conditions require continuous ventilation for vaults and manholes when work is being performed?

A
  1. When an oxygen deficiency is found2. when combustible or explosive gas vapors have been initially detected and reduced to a safe level by ventilation3. When a toxic gas is found4. Where organic solvents are used in the work procedure5. Where the manhole is located in that portion of a public right of way6. open to vehicular traffic and or exposed to seepage of gas or gasses
137
Q

If working in joint power and telecommunications manholes, what procedures must be followed in addition to standard safety precautions?

A
  1. A trained CPR and first aid employee will be available in the immediate vicinity to render emergency assistance as required2. If host employer (company owning the manhole or vault) tests the atmosphere, Comcast’s employee must ensure it is done according to Comcast regulation prior to entry.
138
Q

How often are safety meetings required for field personnel?

A

weekly

139
Q

What field personnel are required to attend safety meetings?

A

installers, technicians, construction, and warehouse

140
Q

How often should a Vehicle Inspection Report be included in safety meetings?

A

Once a month

141
Q

How often should office personnel attend an Employee Safety Meeting?

A

At least once per quarter

142
Q

When was OSHA established?

A

1970

143
Q

OSHA

A

Occupational Safety and Health Administration

144
Q

What is OSHA’s goal?

A

to assure so far as possible every working man and woman in the nation, safe and healthful working conditions and to preserve our human resources.

145
Q

Which OSHA article covers Telecommunications?

A

1910.268

146
Q

Which OSHA article covers Telecommunications?

A

1910.268

147
Q

According to OSHA guidlines, how often should first aid kits be inspected?

A

At least once a month

148
Q

What are the general hardware requirements for body belts, safety straps and lanyards?

A

dropped forge or pressed steel and have a corrosion resistant finish tested to meet the requirements of the American Society for Testing and Materials BI 17-64 (50 hour test)

149
Q

What is the acceptable leakage current for fabric and leather used in safety belts.

A

It may not be used if the leakage current exceeds 1 milli-ampere when a potential of 3,000 volts is applied to the electrodes positioned 12 inches apart.

150
Q

What are the minimum requirements for fabric used in safety straps in an A.C. dielectric test?

A

Must be capable of withstanding an A.C. dielectric test of not less than 25,000 volts per foot “dry” for 3 minutes without visible deterioration

151
Q

what are the safest types of pants to wear when climbing a pole?

A

Straight-legged

152
Q

what is the recommended length of a gaff?

A

1 1/4 inches.

153
Q

how many points of contact should you keep on the pole when you are ascending or descending?

A

3

154
Q

What are the minimum requirements for fabric used in safety straps in an A.C. dielectric test?

A

Must be capable of withstanding an A.C. dielectric test of not less than 25,000 volts per foot “dry” for 3 minutes

155
Q

A conductor or system of conductors through which an electric current is intended to flow

A

Circuit

156
Q

what accessories should be removed before climbing?

A

Metal watchesringskey chainsother simular conductors

157
Q

What are the stitching requirements for body belts, safety straps, and lanyards?

A

minimum 42-pound weight nylon or equivalent thread and shall be locked stitched. Stitching parallel to an edge may not be less than 3/16 inch from the edge of the narrowest member caught by the thread. The use of cross-stitching on leather is prohibited.

158
Q

A conductive connection, whether intentional or accidental, by which an electric circuit or equipment is connected to referenced ground.

A

Ground (as a noun)

159
Q

At what depth is a ladder required to enter/exit a manhole

A

Manholes exceeding 4 feet in depth

160
Q

An electrical connection from one conductive element to another for the purpose of minimizing potential differences or providing suitable conductivity for fault current or for mitigation of leakage current and electrolytic action

A

Bond

161
Q

A material, usually in the form of wire, cable, or buss bar, suitable for carrying an electric current

A

Conductor

162
Q

That conductive body, usually earth, to which an electric potential is referenced.

A

Ground (reference)

163
Q

The connecting or establishment of a connection, whether by intention or accident, of an electric circuit or equipment to referenced ground

A

Ground (as a verb)

164
Q

A subsurface enclosure, which personnel may enter and which is used for thepurpose of installing, operating, and maintaining submersible equipment and/or cable.

A

Manhole

165
Q

what are potential hazards on a pole for gaffing.

A

Knots and knot holesCracks and weathered crackscreosoteexcessive gaff cutsshell rot, other fungus growthlighting or fire damage

166
Q

White is used to indicate what in locating underground utilities?

A

Proposed excavation route

167
Q

What does Pink indicate on an underground locate?

A

Temporary Survey Markings

168
Q

what is a chemical that is put on the poles a a preservative that should be avoided.

A

Creosote

169
Q

What Does Yellow indicate on an underground locate?

A

Gas, Oil, Steam, Petroleum, or Gaseous Materials

170
Q

Each Safety Leader and Field Supervisor will ride along with, or perform job site safety reviews with technicians how often?

A

At least once per quarter, per technician

171
Q

What are the three levels of Comcast safety committees?

A
  1. The corporate-level safety committee2. The divisional-level safety committee3. The system-level safety committee
172
Q

What does Purple indicate on an underground locate?

A

Reclaimed Water, Irrigation and Slurry Lines

173
Q

What are the three recognized categories that accidents can be grouped into?

A

1.Employee Injury2.Motor Vehicle Accident3.General Liability (including property damage and bodily injury to a third party, but excluding injuries sustained as a result of a motor vehicle accident.

174
Q

What does Red indicate on an underground locate?

A

Electric Power Lines, Cables, Conduit and Lighting Cables

175
Q

What does Orange indicate on an underground locate?

A

Communication, Alarm or Signal Lines, Cables or Conduit

176
Q

What does Blue indicate on an underground locate?

A

Potable Water

177
Q

What does purple indicate on an underground locate?

A

Reclaimed Water, Irrigation and Slurry Lines

178
Q

What does Green indicate on an underground locate?

A

Sewer and Drain Lines

179
Q

When you first get to the job site,what should you do before settingup or extending your ladder?

A

Double check the groundwhere the ladder will be set up and checkfor voltage at the pole.

180
Q

when looking at the ground to set up a ladder where should you be looking?

A

Where the ladder will end upafter you apply the 4 to 1 rule.

181
Q

name 5 things to inspect on a ladder?

A

 Rung locks – operate freely Feet are on tight and have theproper protective grips/pads Rungs are solidly in place – notloose, worn, broken or missing Fiberglass rails are solidly in place –no cracks, splinters, dents or wornspots Rope – not frayed, worn or rotten Rung lock flippers – working andnot worn or bent Pulley and mount bracket – notworn or cracked and wheel movesfreely Strand hooks are solidly in place –not bent or cracked Annual inspection tag – in placeand current.

182
Q

what is the foreign voltage test

A

Using avoltage detector, check the pole andany connecting hardware for stray orforeign voltages. If voltage ispresent, contact your supervisor.

183
Q

what is the sound test?

A

Strike the pole with ahammer in several locations fromground level to the highest reachingpoint. If it sounds solid, it should be agood pole. If it sounds hollow, it isprobably a bad pole.

184
Q

what is the prod test?

A

Using a screwdriver atleast 5 inches long or similar proddingtool, attempt to penetrate into thepole just below ground level in acouple of different spots below thesoil surface around the base of thepole. If the tool goes into the polemore than ½ inch, the pole could berotten and may not support theweight of you and your ladder.

185
Q

what is visual inspection?

A

Inspect thepole(s) carefully for conditions, suchas rot, impact damage, cracks,foreign attachments, etc. Look forbee or hornet nests on the bottom oftransformers, phone splice housingsor other attachments.

186
Q

what is the rocking test?

A

attempt to rock thepole back and forth. Caution must beexercised to avoid causing power linesto swing together. If the pole makesa cracking sound during the test, itshall be considered unsafe. Be sureto wear your gloves wheneveryou touch the pole.

187
Q

Which is the safest ladder carry on windy days?

A

Horizontal carry at the hip

188
Q

Which ladder carry should you use if youare traveling more than 15 feet tothe work site and have firm, dryground and little wind?

A

Horizontal carry at the shoulder

189
Q

Which carry can you use for shortdistances, under 15 feet?

A

Half-vertical, half-horizontalcarry

190
Q

Why wouldn’t you use the halfvertical,half-horizontal carry forlonger distances?

A

The ladder isn’t as stable andcarrying it this way puts more strain onyour arms and back

191
Q

Which carry would you use if theground were slippery or unstable?

A

Horizontal carry at the hip

192
Q

When would you use the sidevertical carry?

A

When you are moving theladder just a short distance down thesame leaning surface, like the side of ahouse.

193
Q

Which is the most commonly usedcarry?

A

Horizontal carry at the shoulder

194
Q

What would you do if the pole you areworking on were right next to asidewalk where pedestrians could be?

A

Place cones in a wide areaaround the base of the ladder to steer anypedestrians away from the ladder.

195
Q

What should you do if there is adoorway where you want to placeyour ladder?

A

If it absolutely cannot beavoided, alert the occupants and makesure the door is locked or blocked off. Ifyou can’t ensure your safety, find anotherway.

196
Q

What if you are working on a ladder nearwindows?

A

Don’t put ladders in front ofwindows. Although there is less danger toyou, it is too easy to damage or break awindow with the ladder or another pieceof equipment. For the same reason,never put your ladder against anyequipment or riser on a house or pole.

197
Q

If your ladders are equipped with icetoes, when and how are they used?

A

Ice toes are to be used whenslippery conditions exist. In thesesituations, be sure that the ice toes flipoutward and upward. Gravity will keepthe ladder in position and will keep the icetoes from unintentionally flipping out ofposition.

198
Q

Your ladder is set up against a pole,but before you start ascending, thereare two things you should do. Whatare they?

A

Boots are clean and safety strapis over your shoulder and out of the way.

199
Q

What are some other guidelines youshould keep in mind when you startascending a ladder?

A

Face the ladder; keep bothhands free to grasp the ladder; step onthe arch of the foot with heels snugagainst the rung.

200
Q

What does keeping three points ofcontact mean?

A

Two feet and 1 hand or 2 handsand 1 foot in contact with the ladder at alltimes.

201
Q

We want you to constantly be awareof your overhead clearances,especially power lines, but we alsowant you to be cautious when you arechecking clearances. What shouldyou do?

A

Stop with both feet on theladder whenever you need to look up.Otherwise, keep your focus on your feet.

202
Q

How far from the top of the laddershould you stop?

A

Three rungs from the top.

203
Q

Once you reach the top of the ladder,what should you do prior to beltingon?

A

Lean into the ladder; slide yourfoot forward to lock your heel on therung; spread your feet to the rails; testfor voltage.

204
Q

What must you do before starting totake a ladder down?

A

Put on my work gloves toprotect me against rope burn andfiberglass splinters.

205
Q

When you finish your work, can youjust pick up the ladder and head backto the truck?

A

No, you need to check the pathback and make sure it’s clear, especially ifyou’ve been up there awhile. You mayhave to open some gates or remove someobstacles that have appeared since youwere last there.

206
Q

True of False: the only risk associated with operating an aerial lift is electrocution?

A

False

207
Q

There are _______, ______, ______, and company rulesand regulations governing the safe operation of aeriallifts.

A

Local, State, and Federal

208
Q

It is essential to know the _______ _______ ofan aerial lift vehicle to avoid hitting overheadobstacles while in motion.

A

clearance requirements

209
Q

When working on an incline, what is required toavoid overturning an aerial lift vehicle?

A

extra precautions

210
Q

A malfunction of the ______ _______ may cause the aerial lift to stop functioning?

A

Hydraulic System

211
Q

Prior to operating from an aerial lift bucket at thebeginning of the day, what must first always be tested?

A

The lift controls from the ground.

212
Q

While working in an aerial lift bucket, what must always be worn?

A

An Approved Deceleration Fall Arrest System

213
Q

Who keeps records of all reported work placeincidents?

A

OSHA