RIG CH.7 Flashcards

1
Q

What should be done before using any piece of equipment?

A

Pre-trip inspection

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is the purpose of the outriggers?

A

To stabilize and level the truck

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

T or F: The outriggers are not intended to raise the truck off the ground, they are meant for leveling and stabilization.

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

The boom should only be operated at the lowest half of the swing pattern if the truck is at or greater than this angle?

A

5 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What are the three turret configurations for a digger derrick?

A

Rear center, forward center, and corner mount

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What should any operator refer to prior to using the digger ?

A

boom operational chart

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What is the digger derrick operational zone?

A

The zone in which the boom should be operated.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What should the operator refer to before lifting any load with the boom?

A

load angle chart

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

When is a boom at its strongest?

A

When it is fully retracted and at its highest possible angle.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

When is the load angle chart accurate?

A

When the equipment is level.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

The digger derrick’s ability to lift an object that is within the maximum lift capacity depends on what two factors?

A

Hook radius and sheave height

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is the hook radius?

A

the horizontal distance the hook is from the center of the turret

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What is the sheave height?

A

the vertical distance the sheave is from the height of the turret base

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

How often should AC dielectric tests be performed on material handler booms?

A

Annually

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

T or F: Material handlers can be used even if it is not in a safe working condition.

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

T or F: Material handler trucks have to be level to operate at optimal levels.

A

True

17
Q

T or F: Soil conditions do not affect outriggers and truck setup.

A

False, Soil must be firm enough to allow stability during operation of equipment.

18
Q

What do all aerial lifts have near the turret base?

A

override controls

19
Q

Who is responsible for safety when operating equipment?

A

The operator

20
Q

What is the number of occupants backhoes are designed for?

A

One

21
Q

When driving, operating, and excavating with heavy equipment what is a good general idea on safety?

A

Think about what you are doing and think ahead. Ask yourself how your actions could put others in harm and avoid or change those actions in order to be as safe as possible. Have situational awareness.

22
Q

T or F: Prior to excavation all underground utilities shall be located and marked.

A

True

23
Q

What is the swing radius in regards to heavy equipment?

A

The area the boom moves within.

24
Q

When digging on a slope where should the spoils go?

A

on the uphill side

25
Q

When you leave a backhoe at anytime what should you do?

A

turn the backhoe off and take the keys with you