Practice test C Flashcards

1
Q

You are configuring a new desktop and need to implement full desktop encryption. As you begin the process, you get an error that says that the device cannot be encrypted. Without adding Any hardware, Which of the following should you enable on the desktop computer so that the Drive can be encrypted?

A) TPM
B) secure boot
C) UEFI
D) HSM
E) BIOS
F) EFS

A

TPM

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

You think that the power supply in your PC might be failing, causing issues with a s a t a drive. You decide to test the SATA drive. Which of the following are the standard voltages of a SATA connection on an ATX power supply?

A) 3.3, 5, 12v
B) -3.3, 5, -12v
C) - 5, 5, 12v
D) 5, 12v

A

3.3, 5, 12v

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Which of the following is defined as movement of electrical charge?

A) voltage
B) wattage
C) amperage
D) impedance

A

Amperage

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Which of the following should be used to clean a Laser Printers rubber rollers?

A) soap and water
B) WD-40
C) isopropyl alcohol
D) a moist cloth

A

A moist cloth

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

A co-worker at a satellite office reports that a new replacement shared work group printer has arrived. It is the same model as the old one. Your co-worker replaced the old printer and connected all the cables to the new printer. Which of the following is the easiest way to ensure that all the client computers can connect to the printer via ipp?

A) name the new printer with the old printer name
B) allow the printer to acquire a DHCP address
C) in dhcp, set a reservation by Mac address
D) have your co-worker print the configuration page

A

In dhcp, set a reservation by Mac address

In this scenario, the clients are most likely connecting to the printer using the IP address. Internet printing protocol can be used in this manner. By default, the moment the new printer is connected to the network, it acquires an IP address from the DHCP server, this is a new IP address that is different from the one used by the old printer. This causes the clients to fail when attempting to connect and print to the new printer. To prevent this problem, you can go to the router for another DHCP device and configure a MAC address reservation.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Which of the following protocols can be used to configure and monitor network printer device status?

A) SMTP
B) SNMP
C) TCP/IP
D) IPP
E) DNS

A

SNMP - simple Network management protocol can be used to monitor remote computers and printers. This requires the installation of SNMP on the appropriate hosts. Be sure to use the latest version of SNMP across all devices.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Which of the following symptoms would indicate a power supply issue?

A) the CPU is overclocking
B) the Wi-Fi range is reduced
C) the storage drives fail frequently
D) USB drives are not recognized by Windows

A

The storage drives fail frequently

An indication of a power supply issue is frequent failure of storage drives. If the power supply fails to provide clean power to the 3.3, 5, 12v lines to the drives, those drives will fail frequently. These are often the first devices to fail when a power supply starts having intermittent problems. You should test such issues with a power supply tester or multimeter

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

You are building a new gaming PC and want to select a motherboard that supports the scalable link interface SLI technology so you can install two SLI video cards connected by a bridge. Which of the following expansion slots should the motherboard have for your two video cards?

A) two PCIe version 3 slots
B) two PCIe version 4 slots
C) a PCIe x1 slot and a PCIe x16 slot
D) a USB port and PCIe slot

A

Two PCIe version 4 slots

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which of the following raid arrays is Fault tolerant and allows you to do striping with parity?

A) RAID 0
B) RAID 1
C) RAID 5
D) RAID 10

A

RAID 5

Raid 5 is Fault tolerant and allows for striping with parity if you have at least three drives to dedicate to the array. It is the parody information that makes it fault tolerant

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

A customer wants you to daisy chain 3 monitors. When purchasing the monitors, which of the following video types should you make sure is available?

A) DisplayPort
B) VGA
C) HDMI
D) DVI
E) USB C

A

DisplayPort

The monitors would have to be equipped with DisplayPort version 1.2 or higher or thunderbolt. The computer GPU would have to support DisplayPort 1.2 or higher as well as multi-stream transport mst.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

You are trying to deploy multiple virtual machines to several Intel based desktop computers. Some of the installations are failing because a CPU function is disabled in the bios-uefi. Which of the following should be enabled so that the installations will succeed?

A) TPM
B) hyper threading
C) Intel virtualization
D) VNC

A

Intel virtualization

Intel CPU virtualization is named VT-x. AMD CPU virtualization is named AMD-V

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

A co-worker notices that the battery light on a laptop is flashing when the laptop is in a docking station. Which of the following steps should be performed first to fix the problem?

A) replace the laptop battery
B) reinstall the operating system
C) reseat in the docking station
D) remove and reseat the battery

A

Reseat in the docking station

The laptop probably does not have a sturdy connection and the blinking battery light is telling you that the laptop is not charging properly or at all.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Which of the following steps should be taken to connect a Bluetooth headset to a smartphone? Select the two best answers.

A) pair the device to the phone
B) install Bluetooth drivers
C) enter a passcode
D) disable Wi-Fi

A

Pair the device to the phone
enter a passcode

CompTIA Bluetooth pairing process:
- enable Bluetooth
- enable pairing
- find a device for pairing
- enter the appropriate PIN code
- test connectivity

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Joe’s printer is printing hundreds of pages, and he cannot get it to stop. He has tried to delete the job by double clicking the printer and deleting the print job. Which of the following steps would be the best way to stop the printer?

A) clear The Print Spooler
B) unplug the printer
C) reset the printer
D) turn off the printer

A

Clear The Print Spooler

You do this by stopping The Print Spooler service in computer management or in the Powershell command prompt by entering
net stop spooler
and then deleting the files in the path
C:\Windows\System32\Spool\Printers

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

You are troubleshooting a co-worker’s computer. When you ping the loop back address, you received no response. Which of the following is the most likely cause of the problem?

A) the l a n is unresponsive
B) the DHCP server is down
C) the ethernet cable needs to be replaced
D) the TCP IP protocol is not functioning

A

The tcp/ip protocol is not functioning

Pinging the loopback address should return results even if you are not physically connected to the network.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

A customer brings in a computer that does not display anything when it is turned on. You verify that the computer and monitor are receiving power and that the monitor is securely connected to the computers only video port. Which of the following is the most likely cause of this problem? Select all that apply.

A) motherboard
B) ram
C) storage drive
D) DVD ROM
E) CPU
F) power supply
G) video card

A

Motherboard, ram, cpu, video card

17
Q

While troubleshooting a network problem, you discover that one set of LED lights on a switch is blinking rapidly even when all the other nodes are disconnected. Which of the following is the most likely cause of this problem? Select the two best answers.

A) a switch that is not plugged into a server
B) a defective storage Drive in the computer
C) a defective network card in the computer
D) and unplugged server
E) a defective port on the network switch

A

A defective network card in the computer
A defective port on the network switch

18
Q

You are called to a school lab to fix a computer. The computer supposedly worked fine yesterday, but now it does not power on. The computer is plugged into a power strip with another computer. The other computer works fine. Which of the following are the most likely causes of this problem? Select the two best answers.

A) the power cable is unplugged from the computer
B) the power strip is overloaded
C) the monitor is unplugged
D) the voltage switch on the power supply is set incorrectly
E) the power strip is unplugged

A

The power cable is unplugged from the computer
The voltage switch on the power supply is set incorrectly
A & D

19
Q

You have been tasked with setting up a Wi-Fi thermostat for a customer. The customer has concerns about iot devices getting hacked and possibly acting as gateways to other devices and computers on the network. Which are the best ways to address the customers concern? Select the two best answers.

A) upgrade the customer’s router to the latest firmware version
B) disable wireless access to the thermostat to make it unhackable
C) upgrade the customers wireless network to WPA
D) separate the iot thermostat by placing it in a screened subnet
E) use the latest encryption standard on the wireless network and set a strong password
F) unable to factor authentication for the iot devices cloud account

A

D & E
Separate the iot thermostat by placing it in a screened subnet
Use the latest encryption standard on the wireless network and set a strong password

20
Q

A user reports that a laser printer is printing poorly. You observe that the pages have wrinkles and random patterns of missing print. Which of the following is most likely the cause of this problem?

A) the fuser needs to be replaced
B) the toner cartridge is defective
C) the Corona wire is frayed
D) there is high humidity in the room

A

The fuser needs to be replaced

The wrinkled pages are the number one indicator that the fuser needs to be replaced. Random patterns of missing print further indicate that the fuser is not working properly. Toner not being fused to the paper is the last clue. The fuser usually needs to be replaced every 200,000 Pages or so on a laser printer.

21
Q

Which of the following should be checked when a laptop fails to turn on? Select the four best answers.

A) power LED
B) sound port
C) AC adapter
D) inverter
E) hibernation mode
F) function key
G) power button

A

Power LED, AC adapter, hibernation mode, power button

22
Q

A computer just had a memory upgrade installed. After the computer is booted, it does not recognize the new memory, even though it is listed as being compatible on the manufacturer’s website. Which of the following steps should be performed to resolve the issue?

A) BIOS/UEFI update
B) adjust jumper settings
C) OS update
D) new CMOS battery

A

BIOS /UEFI update

23
Q

A computer has a raid 1 array. S a t a drive 0 failed and now the computer will not boot. You need to boot the computer temporarily to access the data quickly. Which of the following steps would most likely allow the computer to boot again?

A) replace SATA drive one
B) Mark SATA drive one as active
C) replace SATA drive zero
D) replace the arrays controller

A

Mark SATA drive one as active

A raid 1 array is a mirroring array with two drives. The second drive keeps an exact copy of the first drive in real time. If drive one doesn’t take over automatically when drives 0 fails, you have to set it to active. Remember that a partition with an operating system must be set to active, otherwise, the computer will not be able to boot to the partition

24
Q

You are troubleshooting what you believe to be a power issue. Which of the following should be tested first?

A) power supply
B) 24 pin power connector
C) IEC cable
D) AC outlet
E) circuit breaker

A

IEC cable

That is the power cable for the computer, make sure it is connected to the computer and the AC outlet