Module 15 joint and weld types Flashcards

1
Q

Five basic types of joints:
A) butt, edge, Tee, lap and groove
B) butt, Tee, lap, corner and groove
C) butt, Tee, lap, edge, and corner
D) butt, groove, Tee edge and corner Air

A

C) butt, Tee, lap, edge, and corner

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Question to page 21 what type of joint is shown in figure 27
A) plug
B) tee
C) butt
D) lap

A

D) lap

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

A butt joint is a welded joint where the joint parts:
A) lie in the same plane
B) for a corner
C) right angles to each other
D) form a Tee

A

A) lie in the same plane

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

The four main types of welds:
A) groove, fillet, plug and surfacing
B) fill it, Vee, bevel and groove
C) Vee, bevel, bead and fillet
D) groove, Vee, bevel, and plug or slot

A

A) groove, fillet, plug and surfacing

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Name the five types of groove welds

A

Square
Bevel
Vee
J
U

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

On what type of joint would you most likely find groove welds?
A) edge
B) butt
C) fillet
D) lap

A

B) butt

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

The root bead of a groove weld is the
A) last pass of the finished weld
B) widest space between two pieces to be welded
C) layer of material which is intended to fill up the joint
D) first pass or penetration bead

A

D) first pass or penetration bead

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Name the four types of fillet welds

A

Continuous
Intermittent
Chain intermittent
Staggered intermittent

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

On what joints would you find a fillet weld?
A) edge, corner, butt
B) butt, lap, Tee
C) Tee, lap, corner
D) edge, lap,Tee

A

C) Tee, lap, corner

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

The size of a fillet weld is determined by:
A) leg length of the largest leg triangle that may be drawn within the cross-section of the weld
B) measuring across the face of the weld
C) certified welding inspector
D) the thickness of the material being welded

A

A) leg length of the largest leg triangle that may be drawn within the cross-section of the weld

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

To check the size of a convex Philip welded you would measure:
A) leg length of the largest leg triangle that may be drawn within the cross-section of the weld
B) thickness of the material being welded -10% to account for welded metal convexity
C) across the face
D) length of the world

A

A) leg length of the largest leg triangle that may be drawn within the cross-section of the weld

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

The size of groove welds is determined by
A) width between toes
B) throat dimension
C) included angle
D) root radius

A

B) throat dimension

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What is the size of the groove weld in figure 28 on page 22.
A) 9.6 mm (3/8”)
B) 13 mm(1/2”)
C) 14 mm ( 9/16”)
D) 16 mm ( 5/8”)

A

B) 13 mm(1/2”)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

But maybe be done to reinforce welds made on a lap joint
A) place one more pass over the finish weld
B) avoid penetrating the root of the joint with the metal
C) produce a concave finish fillet weld
D) place plug or slot welds along the joint

A

D) place plug or slot welds along the joint

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Why is it sometimes necessary to bevel joint edges prior to welding?
A) to prevent distortion
B) to obtain complete penetration
C) to make the job last longer
D) to provide a clear line to follow one welding

A

B) to obtain complete penetration

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Edge joints are most often used on
A) sheet metal
B) pipe
C) sheet steel over 13 mm (1/2”) thick
D) castings

A

A) sheet metal

17
Q

Which of the following joint preparations on a given material thickness would require the least amount of filler metal
A) double U
B) double Vee
C) single Vee
D) single U

A

A) double U

18
Q

List three reasons why excessive convexity on a fillet weld is considered a welded fault

A

Costly overwhelming, which adds no strength to the joint

Notch affect

Can contribute to excessive distortion

19
Q

Which types of groove welds require only one member of the joint to be prepared
A) square and bevel
B) Vee & J
C) bevel &J
D) U& J

A

C) bevel &J

20
Q

What is the main advantage of the lap joint?

A

No edge preparation is required

21
Q

When using edge, corner and Tee joints, when should you consider preparing the joint edges?
A) when working with light gauge sheet metal
B) when fabricating only with non-Faas metals
C) when working with thicker materials where full penetration is desired
D) when preparing to weld the joint with GMAW

A

C) when working with thicker materials where full penetration is desired

22
Q

What does the G stand for when interpreting the 2G position?
A) grind before welding
B) groove weld
C) gas shielded wire is required
D) see note G on the drawing for welding procedure details

A

B) groove weld

23
Q

What does the three stand for when interpreting the 3F position?
A) three passes required
B) overhead position
C) a 3rd your apprentice is allowed to weld this joint
D) vertical position

A

D) vertical position

24
Q

What is the primary factor in the selection of joint type?
A) accessibility for welding
B) carbon content of the base metal
C) strength and loading requirements
D) available welding, and cutting processes

A

C) strength and loading requirements

25
Q

Selecting a joint preparation that requires the least amount of filler metal
A) but while there’s out of business
B) result in poor penetration
C) make it very difficult to weld
D) minimize distortion and lower cost factors

A

D) minimize distortion and lower cost factors