Minirae3000

Question 1

Uses PID with. 9.8 ev 10.6 ev Or 11.7 ev ____ discharge lamp

Answer 1

Gas-discharge lamp

Question 2

____ hours of continuous monitoring with rechargeable battery pack

Answer 2

16

Question 3

____ point datalogging storage capacity

Answer 3

260,000

Question 4

4.2 V/ 3300mAH ____ battery ____ batteries

Answer 4

Lithium ion battery, 4AA BATTERIES

Question 5

Less than ____ hrs full charge

Answer 5

8

Question 6

—- hours continuous

Answer 6

16

Question 7

Operating in ___ mode

Answer 7

Hygiene and search

Question 8

Humidity is ___ to ___

Answer 8

0% to 95%

Question 9

Measurement range for 10.6 ev is

Answer 9

0.1ppm to 15,000ppm

Question 10

Response time is

Answer 10

2 seconds

Question 11

Flexible ___ “ tubing

Answer 11

5

Question 12

___ VOC gasses

Answer 12

200

Question 13

Accuracy for isobutylene __ to ____ ppm

Answer 13

10 to 2000

Question 14

Sampling pump flow rate is ___ to ____

Answer 14

450 to 550

Question 15

Flashing red LEDs indicate

Answer 15

Exceeded preset limits, low battery, or sensor failure

Question 16

Turning off the instrument hold the ___ key for 3 seconds a 5 second countdown to shutoff begins

Answer 16

Mode

Question 17

Operation mode

Answer 17

Hygiene

Question 18

Pump that provides a 450 to 550cc per minute flow rate l. This pump can pull in air samples from ___ away horizontally

Answer 18

200’

Question 19

This meter is calibrated to

Answer 19

Isobutylene

Question 20

Message: HIGH, OVR, MAX, pump icon flashes, lamp, ___ beeps 1 flashes per second

Answer 20

3

Question 21

Message: TWA, STEL, CAL, NEG, battery icon flashes _ beeps 1 flash per second

Answer 21

1

Question 22

What is the max time for one event

Answer 22

24hrs 28, 800 points

Question 23

How many hours of operation will alkaline batteries have

Answer 23

12

Question 24

What is the external filter made of?

Answer 24

Teflon

Question 25

How do you enter calibration?

Answer 25

Press and hold mode and N/-

Question 26

Under basic user level you

Answer 26

Do not need a password

Question 27

Zero calibration starts a ___ second countdown and displays what message

Answer 27

30s, and zeroing

Question 28

When span calibration is done you’ll see thus message and ppm reading

Answer 28

Span 1 is done! 100.0ppm

Question 29

What is the default password?

Answer 29

0000

Question 30

STEL is expressed in

Answer 30

PPB

Question 31

How to change the gas measurement or correction factor?

Answer 31

Scroll to ppm second one in

Question 32

How to get to the datalog

Answer 32

Fourth to the right (paper looking symbol)

Question 33

The default value is 60s what is the max?

Answer 33

3600

Question 34

What three types of data can you choose?

Answer 34

Average, max, min

Question 35

The time is in

Answer 35

Military

Question 36

When powered on the instrument

Answer 36

Zeros itself

Question 37

In hygiene mode measurements are continuously running in search mode

Answer 37

It is manual start and stop

Question 38

LCD contrast min and max value

Answer 38

20/60

Question 39

How many screws are on the battery compartment

Answer 39

3 Phillips head

Question 40

What are major maintenance items of the instrument

Answer 40

Battery pack, sensor module, PID lamp, sampling pump, inlet connectors and filters

Question 41

When cleaning the PID sensor it is highly recommended that ____ for 15 minutes

Answer 41

An ultrasound bath is to be used to clean the sensor

Question 42

What causes an abnormally high or low reading

Answer 42

Dirty filter or sensor

Question 43

What key do you press and hold to turn on?

Answer 43

Mode

Question 44

Low voltage alarm you should

Answer 44

Turn off the instrument within 10 minutes