Maintenance Forms and Records Flashcards
Where is the record of compliance with Airworthiness Directives or manufacturers’ service bulletins normally indicated?
Aircraft Maintenance Records
If work performed on an aircraft has been done satisfactorily, the signature of an authorized person on the maintenance records for maintenance or alterations performed constitutes
approval for return to service only for the work performed
During an Annual Inspection, if a defect is found which makes the aircraft unairworthy, the person disapproving must
provide a written notice of the defect to the owner
After an annual inspection is performed, any defect found must be listed and provided to the own and kept for how long?
Until the defects are corrected
What is the means by which the FAA notifies aircraft owners and other interested persons of unsafe conditions and prescribes the condition under which the product may continue to be operated?
AIrworthiness Directives
Which is an appliance major repair?
Overhaul of a hydraulic pressure pump
Where should you find this entry?
“Removed right wing from aircraft and removed skin from outer 6 feet. Repaired buckled spar 49 inches from tip in accordance with figure 8 in manufacturer’s structural repair manual No.28-1”
FAA Form 337
Which maintenance action is an airframe major repair?
The repair of portions of skin sheets by making additional seams
Which aircraft record entry is the best description of the replacement of several damaged heli coils in a casting?
Eight 1/4 (20-inch standard heli-coil were replaced. The damaged inserts were extracted, the tapped holes gaged, then new inserts installed and tangs removed
Which maintenance record entry best describes the action taken for a control cable showing approximately 20 percent wear on several of the individual outer wires at a fairlead?
Wear within acceptable limits, repair not necessary
Which maintenance record entry best describes the action taken for a .125-inch deep dent in a straight section of 1/2 inch aluminum alloy tubing?
Dented section removed and replaced with identical new tubing flared to 37 degrees
Which statement is true regarding the requirements for maintenance record format?
Any format which provides record continuity and includes the required information may be used
When a 100-hour inspection is completed, if separate maintenance records for the airframe, powerplant and propellers are maintained, where is the entry for the inspection recorded?
In each record
For aircraft operated under Part 91, when is aircraft total time required to be recorded in aircraft maintenance
After satisfactory completing inspections
For aircraft operated under Part 91, what difference is there, if any, between record entry requirements for maintenance (e.g repair or alteration) and the record entry requirements for inspections (beyond the description of the work performed and the type and extent of inspection)?
Aircraft total time is required to be included only in the inspection entry
If more space is needed for a work description entered on FAA Form 337, what information should be included on the attached sheets in addition to the rest of the work description?
Aircraft nationality and registration mark and the date the work was accomplished
A person installing a product, part or appliance on a type certificated product must take certain that the items record document what type of statement?
Product, part or material meets FAA airworthiness standards
Which aircraft record entry best describes a repair of a dent in a tubular steel structure dented at a cluster?
Welded a reinforcing plate over the dented area
Who is responsible for making entry in the maintenance records after an annual, 100 hour or progressive inspection?
The person approving and disapproving for return to service
For aircraft operated under 91, which of the following records must be retained for at least one year, or until the work is repeated or superseeded?
Records of maintenance, alterations, preventative maintenance, 100 hour, annual and progressive inspections
A certificated mechanic without an inspection authorization who signs the appropriate block on FAA Form 337 is doing what?
Certifying that the work was done in accordance with the requirements of 14 CFR part 43
For aircraft operated under 91, which of the following records must be retained and transferred with the aircraft when it is sold?
Records of current status of applicable AD’s, and date and time when recurring AD’s are next due
If you do an annual on the 15th of the month, when would the next one be due?
The last day of the 12 month
An aircraft owner was provided with a list of discrepancies on an aircraft that was not approved for return to service after an annual inspection. Which of the following statements is/are true concerning who may correct the discrepancies?
- An appropriately rated mechanic
Only 2.
When a discrepancy list is provided to an aircraft owner or operator after an inspection, it says in effect that
except for these discrepancies, the item inspected is airworthy
In order to reconstruct lost or destroyed aircraft maintenance records, what is necessary to establish it?
Total time in service of the airframe
When approving for return to service after maintenance or alteration, the approving person must enter in the maintenance record of the aircraft
a description (or reference to acceptable data) of work performed, date of completion, the name of the person performing the work (if someone else), signature, certificate number, and kind of certificate held
What is/are the appropriate actions concerning minor repairs performed on a certificated aircraft?
- Entries must be made in the aircraft’s maintenance record
2.
When work is performed on an aircraft that necessitates the use of FAA Form 337, who should prepare the form?
The person who performs or supervises the work
What is the status of data used as a basis for approving major repairs or alterations for return to service?
Data must be FAA-approved prior to its use for that purpose
Which statement is true regarding the use of FAA Form 337?
FAA Form 337 is not authorized for use with other than US registered aircraft
After making a certain repair to an aircraft engine that is to be returned to service, an FAA Form 337 is prepared. How many copies are required and what is the disposition of the completed forms?
Two; one copy for the aircraft owner and one copy for the FAA
Who is responsible for upkeep of the required maintenance records for an aircraft?
The aircraft owner
What is Ispec 2000?
Information standards for aviation maintenance
An aircraft was not approved for return to service after an annual inspection and the owner wanted to fly the aircraft to another maintenance base. Which statement is correct?
The owner must obtain a special flight permit
Under what circumstances may the FAA refuse to issue a special flight permit under the provisions of Title 14 CFR Part 21.197?
For conducting customer demonstrating flights in new production aircraft that have not satisfactorily completed production flight tests
Each person performing an annual or 100 hour inspection shall use a checklist that contains at least those items in the
14 CFR Part 43 (could say Appendix D)
An FAA Form 337 is used to record and document
major repairs and major alterations
Major repairs and major alterations to a light sport aircraft requires
an entry into the maintenance records and a FAA Form 337 in duplicate
After a mechanic holding an airframe and powerplant rating completes a 100-hour inspection, what action is required before the aircraft is returned to service?
Make the proper entries in the aircraft’s maintenance record
Which of the following may a certified airframe and powerplant mechanic perform on aircraft and approve for return to service?
1. 100-hour inspections
3. Progressive inspections
1, 3
What is ATA iSpec 2200?
Standardized electronic documentation for aircraft models
