Maintenance Flashcards

1
Q

Pierce Cab full tilt height: ___

A

15’ 10”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

The __ must be set for the hydraulic lift system to operate.

A

brakes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

To raise cab manually
The pump may need
to be cycled ____ before the cab begins to lift.

A

20 or more strokes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Lower cab for an additional ___ after it makes contact with the chassis.

A

5 seconds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

When the pads are new, the floating pin will be exposed ___.

A

3⁄4”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

When the pads are worn to replacement conditions, the floating pin will be nearly flush to the bushing or within ___ of the edge of the rubber bushing (approximately the thickness of a quarter).

A

1/16”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

To manually release the spring brake chamber, unscrew (turn counter- clockwise) the____ located at the end of the spring brake chamber utilizing a ___ or socket assembly.

A

1⁄2” diameter bolt / 3⁄4” box end wrench

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

A Cold Check may be made when the fluid temperature is _____

A

60ºF – 120ºF.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Perform a Hot Check at the first opportunity after normal operating temperature (_____) is reached.

A

160ºF – 200ºF

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

The alternator is a Niehoff ___ and is of the self-energizing type.

A

340 amp

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

The Pierce apparatus has a special receptacle located underneath on the ____ of the apparatus just adjacent to the battery box for connecting to electrical jumper cables.

A

left side

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

The apparatus has a ____ ground electrical system.

A

12V negative

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

To avoid damage to vehicle electronic components, voltage supplied to a vehicle’s electrical system must not exceed ____

A

16.0 volts.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

With the jumper cables properly attached, start the engine of the vehicle with the good (charged) batteries. Run the engine at moderate speed (_____).

A

1000 to 1500 rpm

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The 2005 Pierce Arrow XT utilizes the Kwik-Raze Magnafire 3000 Series H.I.D. Lighting for the 12-volt floodlights on the apparatus. Each light contains a_____.

A

70-watt Metal Halide bulb

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The 70-watt metal halide lamps have an average life expectancy of____, operate at high temperatures and at pressures up to 50 psi.

A

10,000 hours

17
Q

Due to the nature of its attributes, the halide lamp can ___ because of internal or external factors such as ballast failure of particles or misapplication.

A

rupture

18
Q

Turn off/unplug and allow to cool (wait at least___) before replacing bulb.

A

5 minutes

19
Q

Check system voltage with engine off and all electrical accessories off _____

A

(12.9 Volts minimum).

20
Q

Start and run engine, engage high idle and check voltage again ____

A

(13.7 Volts minimum).

21
Q

Weekly

Run engine for _____ at high idle with air conditioning at maximum cool and all electrical accessories activated.

A

10 minutes

22
Q

Check brake lining thickness: Rear at ____ and front pin at ___ note and report.

A

1⁄4” / 1/16”

23
Q

Check pressures by gauge (___ front, ___ rear).

A

120-psi / 90-psi