[Hand, Power, and Measuring Tools] Flashcards

1
Q

Which combination square is used to determine depth?

A

Square head

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

How many blades does a double-tip offset screwdriver have?

A

4 blades

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Which screwdrivers have a thin, round blade and are used to reach and drive or remove screws in deep, counter-bored holes?

A

Common cabinet screwdrivers

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Hammer used like the cross peen but differs from the cross peen since its peening edge is turned ninety degrees to keep the handle parallel to the struck surface

A

Straight peen hammer

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Hammer used as a chisel for removing rivet heads and for stretching or bending metal

A

Cross peen hammer

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Which chisel is used for cutting round stock?

A

Machinist’s cold chisel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What are the two most common types of screw-holding screwdrivers used for working in close quarters, overhead, and hard-to-reach places?

A

1) Clip

2) Sliding collar

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What are the five parts of a file?

A

1) Point
2) Edge
3) Face or cutting teeth
4) Heel or shoulder
5) Tang

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What are the two basic types of screw extractors?

A

1) Straight-flute (requires twist drill, drill guide, and turn nut)
2) Spiral-tapered (requires twist drill)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Which type of file is used for filing circular openings or concave surfaces?

A

Round file

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What type of hammers have a flat striking surface on one end of the head for striking punches and chisels?

A

Machinist’s peens

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Which type of file is used for filing rectangular slots and keyways?

A

Square file

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Which combination square is used to determine an angle?

A

Protractor head

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Which type of wrench is used to connect or break pipe joints or to turn cylindrical parts, and what are the 3 types?

A

Pipe wrench

1) Stillson wrench
2) Strap wrench
3) Chain wrench

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Which screwdrivers are used for working in closer quarters where conventional screwdrivers will not fit?

A

1) Close quarter

2) Stubby common screwdriver

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Which combination square can be used to find the diameter of a cylinder?

A

Center head

16
Q

Cross-tip screwdrivers range in sizes from ___ to ___.

A

1 to 8 inches

18
Q

Which chisel is used for cutting off rivet heads?

A

Rivet buster chisel

19
Q

Cross-point screwdrivers range in sizes from ___ to ___.

*Screw slots meet at an exact right angle at their intersection.

A

3 to 8 inches

20
Q

Hammer used for driving and pulling nails and tapping wood chisels

A

Carpenter’s hammer

21
Q

Which type of file is used to sharpen mill or circular saws, and for draw-filing or finishing metals?

22
Q

Which screwdrivers are used to drive clutchbit screws?

A

Clutch head screwdrivers (old style and new style)

25
Q

Which type of file is used to file in slots and keyways?

A

Pillar files

26
Q

Which type of file is used for filing internal angles and for cleaning out square corners?

A

Three-square file

27
What are used for cutting, smoothing off, or removing small amounts of metal, wood, plastics, or other material?
Files
28
Hammer used for forming soft metal, peening rivet heads, and striking metal in out-of-the-way places
Ball peen hammer
28
What is used to hold or clamp nuts and bolts which have been rounded off by using the wrong size wrench?
Clamp pliers
29
What are the grades of coarseness for the American pattern files?
1) Bastard cut for heavier work 2) Second-cut and smooth-cut for finishing work 3) Dead smooth-cut for extra fine finish
30
Which types of wrenches are used to install or remove odd size nuts and bolts?
Monkey and auto wrenches
32
What are used to remove broken screws without damaging the threads or surrounding material?
Screw extractors
33
What type of wrench is designed to measure the specific degree of tightness of nuts or bolts? What are the two types?
Torque wrench 1) Dial torque 2) Scale torque
33
Which type of files are generally used for fast removal of material and where a precision finish is not required?
American pattern files
34
How quickly should you saw with a hacksaw?
At a rate not to exceed 40-50 strokes per minute
35
What type of extractor is usually a flute type and is used for removing taps with no external area?
Tap extractor
35
Which type of file is used for filing saws having 60 degree angle teeth?
Taper file
36
What is the proper way to select and use a screwdriver?
1) Match the size to the job | 2) Match the type to the head
37
What are the three types of taps? What is used to drill them?
1) Taper, plug, and bottom | 2) Tap wrench