Foam Pro Class “A” Foam System Flashcards

1
Q

The minimum Foam Pro operation rate is what PSI?

A

30 PSI

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

The foam pro has a ___ digit display.

A

5

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

When changing the Foam Pro percentage setting hold the button down for ____ seconds.

A

2

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

The Foam Pro CAL/INJECT valve handle shall be ____ for Normal Operation.

A

In line

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

The Foam Pro CAL/INJECT valve handle shall be _____ for Calibration operation.

A

90 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

The KME uses a Foam Concentrate refill wand that is 1” in diameter and how long?

A

6’

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

The KME Foam tank can be filled through the “power fill” system. The red button places the pump in what mode?

A

Manual mode

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

The KME Foam tank can be filled through the “power fill” system. The green button places the pump in what mode?

A

Automatic refill mode

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

The KME has an automatic refill system. Do not press and hold the button for too long or else?

A

The tank could overfill

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

The Foam Pro proportions at what percentage ranges?

A

.1 % to 3%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

True or false

Do not open foam strainers with Foam Pro System “ON”

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Automatic Refill Operation:

Press the GREEN button once. The pump will start filling the foam tank. The GREEN light will flash on and off while the pump is in operation.
5. When the foam tank is full, the GREEN light will…

A

illuminate solid and the pump will stop.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

The pump will run for ____ seconds and then shut down if no flow is detected by the flow switch. After ____ seconds, the pump will shut down immediately after no flow is detected.

A

20

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

The Foam Pro is a _____ side, direct injection foam system.

A

Discharge

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The Foam Pro system is solely based upon what?

A

Water flow

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

The “ON” status lamp will ______ when foam is injected.

A

Flash

17
Q

The maximum operation pressure of the Foam Pro Model 2001 Foam System is ____ psi.

A

400 psi

18
Q

The foam button is located in the upper-left screen corner. The button is what color?

A

Red

19
Q

Motor stall protection is provided. In the event that the pump motor will not run or stalls for 10 seconds, the display will show “______” to indicate that the pump is producing no feedback to the control signal. The system will return to off status to protect the electric motor and components.

A

ERR.EL

20
Q

Can different brands of “Class A” form or different types of foam such as “Class B” be mixed together in the same tank?

A

Never

21
Q

How do you clear and reset the functions?

A

Using the “SELECT” button, select either “TOTAL WATER” or “TOTAL FOAM”.
By pressing and holding both the and buttons at the same time, the value shown is cleared and displayed as zero.