Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

UAL B787 Study Course > Flight Controls > Flashcards

Flight Controls Flashcards

1
Q

On the ground, above 60 knots groundspeed, the flight control system attempts to maintain a yaw rate near zero by applying rudder input. This function is only available
in: [8.90.10]

A. The NORMAL flight control mode.
B. The SECONDARY flight control mode.
C. The DIRECT flight control mode.
D. All modes.

A

A. The NORMAL flight control mode.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

With a complete loss of flight control signaling, the alternate pitch trim switches must be used to move the stabilizer. [8.90.10]

A. True.
B. False.

A

A. True.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Both the flaps and slats are driven hydraulically in which mode(s): [8.90.10]

A. ALTERNATE mode only.
B. SECONDARY MODE only.
C. PRIMARY mode only.
D. In all modes.

A

C. PRIMARY mode only.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

With the flaps and slats in the SECONDARY mode, if airspeed exceeds 225 knots for the 787-8 or 240 knots for the 787-9 with slats fully extended, they retract to the position. [8.90.10]

A. Retracted
B. 5 degree
C. Middle
D. Slat load relief not available in secondary mode

A

C. Middle

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

On the ground, all spoiler panels extend if both reverse thrust levers are raised to the reverse idle detent. [8.90.10]

A. True.
B. False.

A

A. True.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Which of the following is true when the flight control system is operating in secondary mode? [8.90.10]

A. Autopilot is available.
B. Envelope protection is available.
C. The PFCs are not available.
D. Autopilots and envelope protections are not available.

A

D. Autopilots and envelope protections are not available.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

In the NORMAL flight control mode, the autopilot system sends control surface commands: [8.90.10]

A. Directly to the ACEs.
B. Directly to the PFCs.
C. To the backdrive actuators.
D. Both B and C.

A

D. Both B and C.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

With flight control system operating in the direct mode, the primary flight computers are operative. [8.90.10]

A. True.
B. False.

A

B. False.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

The autopilot is only available in the: [8.90.10]

A. NORMAL and SECONDARY flight control modes.
B. ALTERNATE flight control mode.
C. Only if normal stab trim is available.
D. NORMAL flight control mode only.

A

D. NORMAL flight control mode only.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

The spoilers will automatically extend and the speed brake lever is driven to UP for a rejected takeoff. [8.90.10]

A. True.
B. False.

A

A. True.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

With the flaps and slats in the PRIMARY mode, uncommanded motion will: [8.90.10]

A. Cause the flaps or slats to transfer to the SECONDARY mode.
B. Cause the flap or slat system to transfer to the ALTERNATE mode.
C. Drive the slats to the mid sealed position.
D. Lock out the outboard flaps.

A

A. Cause the flaps or slats to transfer to the SECONDARY mode.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

When operating with the slats in the SECONDARY mode and positioned to the full extended position, if the airspeed exceeds 225 knots for the 787-8, or 240 knots for the 787-9: [8.90.10]

A. The slats will transfer to the ALTERNATE mode.
B. LOAD RELIEF will be displayed on the EICAS.
C. The slats will retract to the middle position.
D. Both B and C.

A

D. Both B and C.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

The primary flight control computers (PFCs) will override a pilot command. [8.90.10]

A. True.
B. False.

A

B. False.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

The flaps and slats in the SECONDARY mode are controlled separately and can be positioned by hydraulic pumps or electric motors. [8.90.10]

A. True.
B. False.

A

A. True.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

In the NORMAL flight control mode, yaw control attempts to maintain zero yaw rate due to engine failure when above: [8.90.10]

A. V1.
B. 60 knots groundspeed and airplane on the ground.
C. 150 knots IAS, with a thrust differential greater than 10%.
D. E/O acceleration height.

A

B. 60 knots groundspeed and airplane on the ground.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Can the Primary Flight Computers be selected to the SECONDARY flight control mode? [8.90.10]

A. Yes, by disconnecting the PFCs.
B. Yes, by disconnecting the autopilot.
C. No, SECONDARY selection occurs automatically.
D. Yes, by disconnecting the Stabilizer Trim.

A

C. No, SECONDARY selection occurs automatically.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Disconnecting the primary flight control computers (PFCs) places the airplane: [8.90.10]
A. In the SECONDARY and DIRECT modes.
B. In the ALTERNATE mode.
C. In the DIRECT mode.
D. Out of control

A

C. In the DIRECT mode.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Wheel to rudder cross-tie is available in which mode(s)? [8.90.10]

A. Secondary and Direct Modes.
B. All modes.
C. Direct mode.
D. Normal mode

A

A. Secondary and Direct Modes.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

The three flight control modes are: [8.90.10]

A. NORMAL, SECONDARY, DIRECT.
B. PRIMARY, SECONDARY, ALTERNATE.
C. NORMAL, SECONDARY, STANDBY.
D. There are only two modes of operation for the Primary Flight Control System.

A

A. NORMAL, SECONDARY, DIRECT.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

With a total hydraulic failure, how are the Pitch and Roll modes controlled? [8.90.10]

A. Electrically using the control wheel.
B. Primary pitch trim switches.
C. Alternate pitch trim switches.
D. All of the above.

A

D. All of the above.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Why is the 787 provided with an electrical flight control backup system? [8.90.10]

A. In case of a dual AC bus failure.
B. In case of a complete hydraulic loss.
C. In case both FMCs are lost.
D. A and C.

A

B. In case of a complete hydraulic loss.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

After landing, the flight control system automatically self-tests: [8.90.10]

A. When the left and right hydraulic systems are depressurized.
B. During engine shutdown, before external power can be connected.
C. When the flaps and speed brakes are retracted and groundspeed less than 30 knots.
D. When the PFCs are disconnected.

A

C. When the flaps and speed brakes are retracted and groundspeed less than 30 knots.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

With the autopilot disengaged, when is manual trimming necessary? [8.90.10]

A. For configuration changes.
B. For airspeed changes.
C. Never, the autopilot trims the airplane.
D. A and B are correct

A

B. For airspeed changes.

17
Q

During takeoff, the rudder becomes aerodynamically effective at approximately 40 knots. [8.90.10]

A. True.
B. False.

A

B. False.

17
Q

The stabilizer green band is calculated by: [8.90.10]

A. The nose gear pressure switch.
B. FMC inputs of CG.
C. FMC Gross weight
D. Both B and C

A

D. Both B and C

18
Q

In the NORMAL mode, pitch trim operates differently on the ground than it does in flight. [8.90.10]

A. True.
B. False.

A

A. True.

19
Q

Both primary and alternate pitch trim switches may be used with the autopilot engaged. [8.90.10]

A. True.
B. False.

A

B. False.

20
Q

The EICAS advisory message STAB GREENBAND is displayed when: [8.90.10]

A. The nose gear pressure transducer and greenband data disagree.
B. The FMC determines the stabilizer is in takeoff low mode.
C. Either nose gear transducer fails.
D. A and C are correct.

A

D. A and C are correct.

20
Q

The ailerons are ___ during high-speed flight. [8.90.10]

A. Locked out
B. Fully deflected position
C. Locked out in low-speed flight
D. Are never locked out

A

A. Locked out

21
Q

Pitch trim is not available if BOTH the L2 and R2 stabilizer control switches are placed to CUTOUT while in the NORMAL flight control mode. [8.90.10]

A. True.
B. False.

A

B. False.

21
Q

Stall protection limits the speed to which the airplane can be trimmed.
[8.90.10]

A. True.
B. False.

A

A. True.

22
Q

Each hydraulic system is dedicated to a different set of spoiler pairs; therefore,
symmetric operation is maintained in the event of hydraulic system failure. [8.90.10]

A. True.
B. False.

A

A. True.

23
Q

The 787 has a single rudder having a hinged section that deflects twice as far to provide additional yaw authority. [8.90.10]

A. True.
B. False.

A

B. False.

23
Q

Some of the benefits of an electronically controlled flight control system (fly-by-wire) are: [8.90.10]

A. Increased fuel economy.
B. Enhanced handling qualities.
C. Reduced pilot workload.
D. All of the above.

A

D. All of the above.

23
Q

When is the slat auto gap function available? [8.90.10]

A. Flaps are in the primary mode with the slats in the middle position.
B. Airspeed below 225 KIAS for the 787-8.
C. Airspeed below 240 KIAS for the 787-9.
D. All of the above.

A

D. All of the above.

24
Q

Which of the following are limitations on the use of speed brakes? [1.30]

A. Do not use the speed brakes with flaps 25 or 30.
B. Do not use speed brakes with the gear down.
C. Speed brakes can be used at any altitude.
D. Do not use the speed brakes inflight below 1000 feet.

A

D. Do not use the speed brakes inflight below 1000 feet.

24
Q

The ___ are locked out during high-speed flight. [8.90.10]

A. Ailerons
B. Ailerons and spoilers 5 and 10
C. Ailerons and spoilers 4, 5, 10, and 11
D. Spoilers 5 and 10

A

A. Ailerons

24
Q

The Wheel to Rudder Cross-Tie system operates in conjunction with the Thrust Asymmetry Protection function and is effective both on the ground and in the air. [8.90.10]

A. True.
B. False.

A

B. False.

25
Q

The yaw control function for asymmetry compensation is inoperative in the Secondary and Direct flight control modes. [8.90.10]

A. True.
B. False.

A

A. True.

25
Q

Which of the following functions are not available in the Secondary Mode? [8.90.10]

A. Wheel to rudder cross-tie.
B. Envelope protection.
C. Auto speed brakes.
D. B and C.

A

D. B and C.

26
Q

If the flap placard speed is exceeded with flaps in the position for the 787-8/-9/-10, LOAD RELIEF is displayed and the flaps automatically retract to a position appropriate for the airspeed. [8.90.10]

A. 15 through 30
B. 1 through 30
C. 5 through 30
D. A and B are correct

A

A. 15 through 30

27
Q

Tail strike protection cannot be overridden by pilot input. [8.90.10]

A. True.
B. False.

A

B. False.

27
Q

Roll control wheel input beyond 35° of bank causes: [8.90.10]

A. The control wheel force rolls the airplane back to level flight.
B. The PFD bank indicator turns amber.
C. The control wheel force will not allow the pilot to override its inputs.
D. Both A and B are correct.

A

B. The PFD bank indicator turns amber.

28
Q

Automated yaw and roll control for engine failure, crosswind, or turbulence is an integral part of the flight control system. [8.90.10]

A. True.
B. False.

A

A. True.

29
Q

On landing automatic or manual trim inputs are zeroed after landing. [8.90.10]

A. True.
B. False.

A

A. True.

30
Q

Autodrag operates only when on an electronic glideslope or FMC generated glidepath is captured. [8.90.10]

A. True
B. False

A

B. False

31
Q

Wheel to rudder cross tie is not provided in the ___ flight control mode because the flight control system automatically controls sideslip and fin loads. [8.90.10]

A. Secondary
B. Direct
C. Normal
D. Alternate

A

C. Normal

31
Q

In the air, the spoilers automatically retract and the speed brake lever is driven forward to the DOWN position when either thrust lever is approximately 70% of full travel. [8.90.10]

A. True.
B. False.

A

A. True.

32
Q

Pre-Gap functions when: [8.90.10]

A. The flaps are operating in secondary mode
B. Airspeed is below 225 on the -8 and below 240 on the -9/-10
C. The flap lever is out of up
D. All of the above conditions exist

A

D. All of the above conditions exist

32
Q

Rudder trim is automatic in all flight phases in the ___ flight control mode,
including during engine failure. [8.90.10]

A. Secondary and Direct
B. Secondary
C. Direct
D. Normal

A

D. Normal

33
Q

FLAP LOAD RELIEF protects flaps from excessive airload by: [8.90.10]

A. Retracting flaps back to a setting based on current speed, not to exceed flaps 5
B. When speed is reduced, the flaps will return to the flap handle setting
C. Only when operating in the Secondary and Direct flight control modes
D. Both A and B

A

D. Both A and B

34
Q

Land Attitude Modifier (LAM) is an automatic function used to increase: [8.90.10]
A. Pitch attitude.
B. Air speed.
C. Nose gear height.
D. both A and C.

A

D. both A and C.

35
Q

With Autopilot engaged, moving any pitch trim switches will disengage the autopilot [8.90.10]

A. True
B. False

A

B. False

36
Q

Stall Protection reduces the likelihood of inadvertently exceeding the stall angle of attack by: [8.90.10]

A. Providing enhanced pilot awareness of the approach to a stall.
B. Limited the speed to which the airplane can be trimmed.
C. Allowing the airplane to be trimmed in a nose up attitude.
D. Both A and B.

A

D. Both A and B.

37
Q

The EICAS advisory message STAB GREENBAND is displayed if the following occurs: [8.90.10]

A. Computed green band disagrees with pressure transducer data.
B. The 2 transducer values are not within the set tolerance.
C. Either transducer has failed.
D. Any of the above.

A

D. Any of the above.

38
Q

Autodrag function operates by deflecting the ailerons downward in conjunction while stowing the outboard spoilers. [8.90.10]

A. True
B. false

A

B. false

UAL B787 Study Course (19 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions