Fire Alarm CH 2 Flashcards

1
Q

signaling line circuits monitor for integrity by?

A

polling or interrogation of circuit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

wiring between enclosures is not required to be monitored for integrity if the enclosures are less than 10 inches apart and the wiring is _________

A

installed in conduit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

initiating device circuits and notification appliance circuits monitor for integrity by?

A

a small current through the circuit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

list 3 examples of an installer who is “qualified and experienced” under the requirements of NFPA 72

A

Nicet certified
IMSA certified
Certified by state or local authority

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Opens and grounds on a fire alarm circuit will result in a _______ signal.

A

trouble

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

if a system standby load is 350 milliampers and the alarm load is 1.100 amperes what is the required capacity of a battery used for a secondary power supply

A

10.19A

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

secondary power supplies must supply power to protected premises fire alarm systems for a minimum of?

A

24 hours of standby power followed by 5 min of alarm

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

the code requires the maximum normal operating temperatures for most fire alarm equipment to be between

A

32 and 120 degrees F

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

notification appliances commonly us a ______ to prevent monitoring current to pass through the notification appliance circuitry>

A

blocking diode

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

upon detection of a trouble condition, fire alarm systems controls must initiate a trouble signal within _________ seconds

A

200 seconds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

conductors returning to the control unit from the last field device on the circuit might indicate?

A

Class A

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

which circuit class is considered as “fail-safe”?

A

class D

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

the disconnecting means (branch circuit) for the primary power of a fire alarm system must be _____ in color

A

red

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Class ______ circuits are not required to be monitored for integrity

A

class E

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

where an engine-driven generator is used to provide secondary power a minimum of ______ hours of batteries are required. why?

A

4 hours in case generator does not start

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Duct smoke detectors are sometimes permitted to cause a _________ signal in place of an alarm signal

A

supervisory

17
Q

all devices on signaling line circuits have ____________.

A

unique addresses

18
Q

secondary power supplies must supply power to an in -building fire emergency voice/alarm communications fare alarm system for a minimum of?

A

24 hours of standby followed by 15 min of alarm

19
Q

an emergency communication system can be used to warn occupants of a _____, _______, or _______>

A

fire
terrorist attack
tornado

20
Q

Fire alarm control equipment requires a smoke detector for protection when the controls are _______.

A

Located in an area that is not continuously occupied

21
Q

wiring between enclosures is not required to be monitored for integrity if the enclosures are less than _______ apart and the wiring is installed in conduit

A

10 inches

22
Q

section _______ of NFPA 72 requires all circuits to be monitored for integrity.

A

12.6

23
Q

why is t-tapping not permitted on initiating device circuits, notification appliance circuits, and class a signalling line circuits?

A

not monitored for integrity.

24
Q

a valve tamper switch, when actuated, will produce a ______ signal.

A

supervisory

25
Q

list three signals produced by a fire alarm system.

A

alarm - GTFO
supervisory - something is off normal
trouble - something is wrong with the wire

26
Q

alarm signals are indicative of a ______.

A

fire or other life threatening emergency.

27
Q

which of the following documentation must be provided to the authority having jurisdiction at the completion of a fire alarm installation

A

record of completion